• Journal of the Korean Geotechnical Society
• /
• v.35 no.6
• /
• pp.5-15
• /
• 2019

Usually, the cyclic shear stress ratio (CSR) for the assessment of liquefaction has been determined by performing ground response analysis or adopting simplified method suggested by Seed & Idriss with some modifications. In order to analyze the applicability of the CSR evaluation methods, the present study performed one-dimensional equivalent linear analysis and evaluated CSR based on design codes from FHWA, JRA, and KDS. The comparison of the CSR obtained from each code showed that the CSR from KDS showed the largest error with the analysis results. The reason is because KDS has an error, which defines the stress reduction coefficient applying the maximum acceleration at each depth, not the maximum cyclic shear stress mobilized in the soil.

• The Journal of Advanced Prosthodontics
• /
• v.13 no.1
• /
• pp.12-23
• /
• 2021

Purpose. The aim of the study was to compare the lingualized implant placement creating a buccal cantilever with prosthetic-driven implant placement exhibiting excessive crown-to-implant ratio. Materials and Methods. Based on patient's CT scan data, two finite element models were created. Both models were composed of the severely resorbed posterior mandible with first premolar and second molar and missing second premolar and first molar, a two-unit prosthesis supported by two implants. The differences were in implants position and crown-to-implant ratio; lingualized implants creating lingually overcontoured prosthesis (Model CP2) and prosthetic-driven implants creating an excessive crown-to-implant ratio (Model PD2). A screw preload of 466.4 N and a buccal occlusal load of 262 N were applied. The contacts between the implant components were set to a frictional contact with a friction coefficient of 0.3. The maximum von Mises stress and strain and maximum equivalent plastic strain were analyzed and compared, as well as volumes of the materials under specified stress and strain ranges. Results. The results revealed that the highest maximum von Mises stress in each model was 1091 MPa for CP2 and 1085 MPa for PD2. In the cortical bone, CP2 showed a lower peak stress and a similar peak strain. Besides, volume calculation confirmed that CP2 presented lower volumes undergoing stress and strain. The stresses in implant components were slightly lower in value in PD2. However, CP2 exhibited a noticeably higher plastic strain. CONCLUSION. Prosthetic-driven implant placement might biomechanically be more advantageous than bone quantity-based implant placement that creates a buccal cantilever.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.328-332
• /
• 1993

Single overload tests are carried out for SS41. Specimens are used hollow type and solid type that stress condition prevail plane stress and plane strain at surface crack. According to the crack initiation and propagation period, single overload applies to three regime and overload ratios change into 1.5, 2.0. Crack retardation zones at initation range aren't different in both specimens respectively, however at propagation range come into large scale in hollow specimen. Delayed load cycles come into large scale in solid type. And the more the overload ratio increase, the larger the retardation zone increase but the magnitude doesn't exactly equal to the expected from the overload ratio.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.11a
• /
• pp.263-269
• /
• 2002

Design method for Involute bevel gears is developed. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is MS(matrix search) which is developed from this study. Design variables are pressure angle 20, transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Design method developed this study can bd applide to the plane, machine tools, automobiles.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.71-77
• /
• 1984

Stress analysis of split ring with four different radius ratios under the compressive load is made by the photoelastic experiment and the numerical analysis through the FEM. The results of the two methods agreed well. Above results are also compared with those of the theoretical formula in order to confirm the range in which the formula of the curved bar is applied in connection with the radius ratio. The results of the two methods agreed well with those of the formula for the radius ratio, 3/2 and 9/7 within small errors of around 7% and 5% respectively.

• Proceedings of the KWS Conference
• /
• 1999.05a
• /
• pp.288-291
• /
• 1999

Fatigue crack propagaion rates and characteristics of the SA516-70 steel which is used for the low temperature pressure vessels, were studied in the room temperature of 1$0^{\circ}C$ and low temperature ranges of -1$0^{\circ}C$, -3$0^{\circ}C$, -5$0^{\circ}C$, -7$0^{\circ}C$ with stress ratio of R＝0.05.

• Journal of Ginseng Research
• /
• v.3 no.2
• /
• pp.168-186
• /
• 1979

Three hundred gram of Korean ginseng root was extracted with 95% ethanol on a boiling water bath for about 300 hr. Evaporation of alcohol yieled 50.2g of dark brown residue which was used by dissolving 4 mg of the residue in 1 ml of physiological saline. The ginseng group and the saline group received each day 0.5 ml per 100 g body weight of ginseng extract and physiological saline, respectively. Both the ginseng and saline group with stress were exposed to positive radial acceleration (1∼29g), cold (5$^{\circ}C$, 0$^{\circ}C$ &-10$^{\circ}C$) and heat (35$^{\circ}C$) environment, and surgical stress. After termination of the last stress, the tolerance, body weight, visceral organ weight, basal metabolism rate, rectal temperature, the number of erythrocyte and leucocyte, hemoglobin level, hematocrit ratio, total serum protein content and it's fraction and the content of adrenal ascorbic acid in the experimental animal exposed to stress were measured and at the corresponding periods, the same measurements were also carried out with the ginseng and the saline groups without stress exposure (serving as control). Results obtained were as follows. 1. Administration of ginseng does depressed the decrease of the tolerance, body weight, visceral organ weight, basal metabolism rate, the number of erythrocyte, hemoglobin value, hematocrit ratio and the A/G ratio in the mice and rats exposed to various stress. 2. The change of the rectal temperature, eosinophile counts, total serum protein content and the content of adrenal ascorbic acid of ginseng group that exposured to various stress facilitates the reaction to, and accelerates the recovery from the stress. 3. Even after hypophysectomy which served the link between the central and the peripheral portion of the stress mechanism, the adrenal ascorbic acid content of ginseng group decreased significantly more than that of the saline group 30 min. after administration of ACTH, while the value approached the normal level significantly closer in the ginseng group than in the saline group 1 and 2 hr after ACTH administration. Judging from the above results, it is concluded that administration of ginseng extract tolerated the experimental animals under the environment of stressfu1 stmuli, although the ginseng has no significant influence upon the stress mechanism in the absence of stressful stimuli. The site of action of the ginseng appears to be in the peripheral portion of the stress mechanism.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.318-324
• /
• 2005

Theoretical efforts are performed to extend the formulation of NSLT(New Shear Lag Theory) for the prediction of the elastic modulus in short fiber composite. The formulation is based on the elastic stress transfer considering the stress concentration effects influenced by elastic modulus ratio between fiber and matrix. The composite modulus, thus far, is calculated by changing the fiber aspect ratio and volume fraction. It is found that the comparison with FEA(Finite Element Analysis) results gives a good agreement with the present theory (NSLT). It is also found that the NSLT is more accurate than the SLT(Shear Lag Theory) in short fiber regime when compared by FEA results. However, The modulus predicted by NSLT becomes similar values that of SLT when the fiber aspect ratio increases. Finally, It is shown that the present model has the capability to predict the composite modulus correctly in elastic regime.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.69-77
• /
• 1996

This study aims to analyze the S. I. F. K value upon Mode I cracks in a finite-width plate of varying thickness, which is expressed in terms of width ratio ($\omega$), thickness ratio ($\beta$) and non-dimensional crack length (λ) by using the 2-dimensional finite element method. Then, by comparing the effectiveness of the results obtained by the two finite element methods, it is seen that the 2-dimensional finite element method can be used in order to analyse the S. I. F. K values upon a various thickness model. A model is developed in order to analyze the effects of initial residual stress upon the fatigue crack growth behavior in various thickness welded specimens. In this model, crack growth rate da/dN appears to be come small as the thickness ratio with the same ΔK is increased. Also, in the initial step, as ΔK is increased with crack growth rate is decreased and then increased because the repeated compressive residual stress retards crack growth rate.

• Textile Coloration and Finishing
• /
• v.15 no.6
• /
• pp.33-38
• /
• 2003

This study surveys the effects of POY physical properties and processing conditions of belt texturing machine to the textured yarns. The various textured yarns are made with the variations of 1st heater temperature, draw ratio, velocity ratio, and the physical properties of these specimens such as yam linear density, tenacity, breaking strain, and wet and dry thermal shrinkages are measured and analysed with the various processing conditions of texturing machine. Especially, the thermal characteristics of the textured yarns, which are affected at the fabric hands and the determination of the processing conditions in the dyeing and finishing processes, are investigated through the thermal stress analyser and DSC experiments.