기존의 블록식 보강토옹벽의 경우 블록과 보강재 연결을 핀, 커텍터 등으로 연결하므로 전면부에 응력집중이 발생하여 블록의 균열이나 보강재 파단파괴가 발생할 수 있는 단점이 있다. 이에 본 연구는 보강재의 침하를 허용하는 새로운 연결시스템을 개발하여 연구대상지역에 일반형 블록식 보강토옹벽 구간과 보강재 침하형 보강토옹벽 구간으로 나누어 시험시공을 실시하였다. 시공과정 및 이후의 현장계측결과 전면블록에 인접한 부분에서 최대인장력으로부터 구한 인장력비가 일반형 보다 침하형이 전면블록 전면부의 음력집중이 크게 감소하는 것으로 나타났다.
도수 또는 중력 외회전 부하 방사선 검사는 족관절 양과 유사 골절과 단독 외과 골절을 구별할 수 있는 기준이 된다. 부하 방사선 검사상 내측 관절 간격이 넓어지면 삼각인대 손상을 진단할 수 있고 비골 골절에 대한 수술적 처치가 권장된다. 비골 골절에 대하여 관혈적 정복술 후 Cotton test를 시행하여 경비원위인대가 벌어질 경우 이에 대한 고정을 시행한 후 삼각인대의 봉합술 시행 여부는 술자의 선호도 및 수술장 내 소견에 의하여 결정된다. 삼각인대 봉합술은 내과에 suture anchor를 삽입하고 심부와 천부 삼각인대에 대하여 중첩술 후 내과에 anchor를 통하여 고정함으로써 시행한다. 유일하게 무작위로 시행된 족관절 골절에서의 삼각인대 봉합술의 유용성 평가 연구에서는 삼각인대 봉합술의 유용성에 대하여 긍정적인 결론을 도출하지 못하였으나 연구 자체의 제한점이 많아 해석을 하는 데 있어 한계가 있었다. 추후 이에 대한 심도 있는 연구가 필요하리라 판단된다.
Objectives: The authors tried to analyze the results of carotid artery sacrifice with or without preoperative carotid evaluation. Materials and Methods: Thirteen patients undergone carotid sacrifice were evaluated. Carotid balloon occlusion test (BOT) and single-photon emission computed tomography (SPECT) with technetium-99m-labeled hexamethylpropyleneamineoxime ($^{99m}Tc-HMPAO$) were used for preoperative carotid evaluation. Results: The causes of carotid artery sacrifice consisted of the neck mass involving the carotid artery, spontaneous aneurysmal rupture, and traumatic pseudoaneurysm. Five patient had postoperative neurologic complications and two of them had permanent neurologic deficits. Conclusion: The authors stress that the preoperative evaluation in carotid artery sacrifice is imperable, and the BOT with SPECT can be used in selecting the method of treatment. But since these tests cannot predict the postoperative outcome perfectly, careful perioperative care of the patients should be exercised regardless of the results of the preoperative evaluation.
경량 골재 콘크리트의 역학적 특성에 대한 천연모래 치환율과 경량 굵은 골재 최대 크기의 영향을 평가하기위해 15배합의 실험이 진행되었다. 경화된 경량 골재 콘크리트의 공극률 및 기건 단위 질량, 재령에 따른 압축강도 발현, 인장저항성능, 탄성계수, 파괴계수 및 응력-변형률 관계를 측정하였다. 측정된 역학적 특성들은 ACI 318-08, EC2 및 CEB-FIP 기준 또는 Slate 등, Yang 등 및 Wang 등의 제안모델들과 비교하였다. 실험 결과 경량 골재 콘크리트의 압축강도는 굵은 골재 최대 크기가 클수록 그리고 경량 잔골재 양이 증가할수록 감소하였다. 경량 골재 콘크리트의 압축강도 발현에 대한 상수는 굵은 골재의 비중과 천연모래 치환율의 함수로서 제시될 수 있었다. 한편, 측정된 경량 콘크리트의 파괴계수 및 인장강도는 설계기준 및 제안모델들에 비해 일반적으로 낮았는데, 이는 경량 콘크리트의 인장저항성은 압축강도뿐만 아니라 기건 단위 질량에 의해서도 영향을 받기 때문이다.
본 연구는 폴리머 기반 보수모르타르에 미분쇄된 플라이애시 치환율의 영향을 평가하였다. 주요변수는 양생온도와 미분쇄된 플라이애시의 치환율이다. 양생온도는 $40^{\circ}C$, $20^{\circ}C$ 및 $5^{\circ}C$로, 미분쇄된 플라이애시 치환율은 결합재 대비 0~35%로 변화하였다. 굳지 않은 모르타르에서는 플로우를, 굳은 모르타르에서는 재령별 압축강도, 응력-변형률 관계 및 탄성계수, 파괴계수를 측정하고, 주사전자현미경 및 엑스선회절기 분석을 수행하였다. 실험결과 보수모르타르의 플로우, 탄성계수 및 파괴계수는 미분쇄된 플라이애시 치환율 20~30%에서 가장 높은 성능을 발휘하였다. 또한 재령별 압축강도는 미분쇄된 플라이애시 치환율과 양생온도에 현저한 영향을 받았는데, 미분쇄된 플라이애시 치환율 20%에서 초기강도 발현율이 가장 높았다. ACI 209에서 제시하고 있는 콘크리트 재령별 압축강도예측모델에서 초기 및 장기재령 강도발현 계수는 미분쇄된 플라이애시 치환율과 양생온도의 함수로 일반화할 수 있었다. 미분쇄된 플라이애시가 첨가된 페이스트는 수화생성물을 나타내는 피크(peak)의 수와 강도(intensity)가 증가되고 플라이애시 입자주변에 CSH 겔이 형성되었다.
목적: 슬관절의 후방십자인대 파열시 잔존하는 절단단 또는 이완된 인대를 유지하면서 신선 동결 동종 아킬레스건을 이용하여 재건술을 시행한 결과를 후향적으로 분석해 보고자 하였다. 대상 및 방법: 2004년 10월부터 2010년 3월까지 후방십자인대 완전 파열로 진단되어서 동종 아킬레스건을 이용한 재건술을 시행한 환자 중에서 최소 1년 이상 추시가 가능하였던 22례를 대상으로 하였다. 평균 추시는 3년 7개월(1년~6년 4개월)이었다. 수술시 연령은 평균 31.5세 이었으며, 성별은 남자가 14례, 여자가 8례였다. 운동 가능 범위, 후방 전위 검사, Telos stress 방사선 검사, Lysholm knee score, Tegner activity score, International Knee Documentation Commiittee (IKDC)의 판정 기준을 이용하여서 술 후 기능 평가, 2차적 관절경 검사 등을 시행하여 주관적 및 객관적 지표로 삼았다. 결과: 슬관절 안정성에 대한 이학적 검사인 후방 전위 검사, 최종 추시 시에 후방 스트레스 방사선 사진, Lysholm knee score, Tegner activity score, IKDC score 등은 통계학적 의의가 있는 좋은 결과를 보였다. 결론: 후방십자인대 파열시 잔존하는 인대의 절단단 또는 이완된 인대를 유지하면서 신선 동결 동종 아킬레스건을 이용한 재건술은 양호한 슬관절의 안정성과 기능 회복을 얻을수 있는 좋은 수술 방법으로 사료된다.
이 연구의 목적은 국내생산이 가능한 자철석을 이용한 중량 콘크리트의 유동성 및 역학적 특성을 평가하고 설계기준의 안전성을 확인하는 것이다. 주요변수로는 물-시멘트 비와 보통중량 굵은골재(화강석)의 치환율이다. 배합된 콘크리트 기건 단위용적질량은 $2446{\sim}3426kg/m^3$ 범위에 있었다. 측정된 역학적 특성들은 압축강도, 응력-변형률관계, 탄성계수, 쪼갬인장강도, 파괴계수 그리고 철근과의 부착응력-미끄러짐 관계 등이다. 실험 결과, 자철석 중량 콘크리트의 초기 슬럼프는 보통중량 굵은골재 치환율이 증가할수록 향상하였다. 압축강도, 인장저항성 등의 역학적 특성은 굵은골재 치환율에 따른 영향이 미미하였으나, 응력-변형률 관계와 탄성계수는 콘크리트 단위용적질량에 중요한 영향을 받았다. ACI 349-06 및 CEB-FIP 제안모델들은 일반적으로 자철석 중량 콘크리트의 역학적 특성들에 대해 안전측에 있지만, 탄성계수 및 쪼갬인장강도에 대해서는 콘크리트 단위용적질량을 고려하여 보완될 필요가 있었다.
Cu have been widely used as signal transmission materials for electrical electronic components owing to its high electrical conductivity. However, it's size have been limited to small ones due to its poor mechanical properties, Until now, strengthening of the copper at toy was obtained either by the solid solution and precipitation hardening by adding alloy elements or the work hardening by deformation process. Adding the at toy elements lead to reduction of electrical conductivity. In this aspect, if carbon nanofiber is used as reinforcement which have outstanding mechanical strength and electric conductivity, it is possible to develope Cu matrix nanocomposite having almost no loss of electric conductivity. It is expected to be innovative in electric conduct ing material market. The unidirectional alignment of carbon nanofiber is the most challenging task developing the copper matrix composites of high strength and electric conductivity In this study, the unidirectional alignment of carbon nanofibers which is used reinforced material are controlled by drawing process in order to manufacture the intermediary materials for the carbon nanofiber reinforced Cu matrix nanocomposite and align mechanism as well as optimized drawing process parameters are verified via experiments and numerical analysis. The materials used in this study were pure copper and the nanofibers of 150nm in diameter and of $10~20\mu\textrm{m}$ In length. The materials have been tested and the tensile strength was 75MPa with the elongation of 44% for the copper it is assumed that carbon nanofiber behave like porous elasto-plastic materials. Compaction test was conducted to obtain constitutive properties of carbon nanofiber. Optimal parameter for drawing process was obtained by experiments and numerical analysis considering the various drawing angles, reduction areas, friction coefficient, etc Lower reduction areas provides the less rupture of cu tube is not iced during the drawing process. Optimal die angle was between 5 degree and 12 degree. Relative density of carbon nanofiber embedded in the copper tube is higher as drawing diameter decrease and compressive residual stress is occurred in the copper tube. Carbon nanofibers are moved to the reverse drawing direct ion via shear force caused by deformation of the copper tube and alined to the drawing direction.
To study the evolution mechanism of cracks in rocks with multiple defects, rock-like samples with multiple defects, such as strip-shaped through-going cracks and cavity groups, are used, and the crack propagation law and changes in AE (acoustic emission) and strain of cavity groups under different inclination angles are studied. According to the test results, an increase in the cavity group inclination angle can facilitate the initial damage degree of the rock and weaken the crack initiation stress; the initial crack initiation direction is approximately 90°, and the extension angle is approximately 75~90° from the strip-shaped through-going cracks; thus, the relationship between crack development and cavity group initiation strengthens. The specific performance is as follows: when the initiation angle is 30°, the cracks between the cavities in the cavity group develop relatively independently along the parallel direction of the external load; when the angle is 75°, the cracks between the cavities in the cavity group can interpenetrate, and slip can occur along the inclination of the cavity group under the action of the shear mechanism rupture. With the increase in the inclination angle of the cavity group, the AE energy fluctuation frequency at the peak stress increases, and the stress drop is obvious. The larger the cavity group inclination angle is, the more obvious the energy accumulation and the more severe the rock damage; when the cavity group angle is 30° or 75°, the peak strain of the local area below the strip-shaped through-going fracture plane is approximately three times that when the cavity group angle is 45° and 60°, indicating that cracks are easily generated in the local area monitored by the strain gauge at this angle, and the further development of the cracks weakens the strength of the rock, thereby increasing the probability of major engineering quality damage. The research results will have important reference value for hazard prevention in underground engineering projects through rock with natural and artificial defects, including tunnels and air-raid shelters.
This study was conducted to investigate the main factors that contain a rotating velocity ratio between wheel and conveyor belt, a tilt angle of conveyor belt and a rotating velocity of a dick cutter for mechanization of Chinese leek harvest. In the survey on the cultivation of Chinese leek, row spacing of 350 m and cutting height of 10 mm from the ground were set up for field tests. Test equipment was designed to cut, pick up and convey Chinese leek one row by one row. From the results of material tests, pick-up height of conveyor belt was set up at $60\~90m$ from the bottom, and the strain and stress at rupture of Chinese leek was 0.487 m/m and 0.01078 MPa. An elastic coefficient of the rubber (Neoprene) of conveyor belts was 1.1077 under the strain of 0.3 nym. from the results of field tests, the tilt angle of conveyor belt was the range of $25^{\circ}\~30^{\circ}$ under consideration far space of container, the velocity ratio between vehicle and conveying belt was 1 to 2.4~1.7 at 0.1~0.3 m/s of vehicle, and optimum rotating velocity of the disk cutter was 34.8 m/s or more under consideration for soil friction.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.