• 한국안전학회지
• /
• 제16권2호
• /
• pp.44-50
• /
• 2001

The rotated bending fatigue test was conducted in air md in 3.5% NaCl salt solution to investigate the fatigue fracture behaviour of raw material and F.E.M dual phase steel made from raw material(SS41) by a suitable heat treatment. This study has compared the initial microcrack creation of material by tensile test with that by fatigue test. And the rotated bending test of cantilever type under the condition of 3.5% NaCl salt solution and air has investigated the corrosion fatigue fracture behaviour with the variation of stress concentration factor determined by each of notch shapes. The initial microcrack have been developed in fragile grainboundary with general corrosion occurring in raw material : in the pits built up by corrosion in F.E.M. dual phase steel because pits bring out stress concentration. It is small that the degree of decrease in corrosion fatigue life for F.E.M. dual phase steel compared with raw material because the notch sensitivity of F.E.M. dual phase steel is lower than raw material in reason of characteristics with two-phase construction.

• 대한기계학회논문집A
• /
• 제38권2호
• /
• pp.167-175
• /
• 2014

가동중검사 동안 가압중수로 압력관에서 탐지된 베어링 패드 프레팅 결함, 이물질 프레팅 결함 등 체적결함에 대해서는 CSA N285.8-05 에 따라 탄성 응력집중계수 수식을 이용하여 피로균열 및 수소지연균열이 개시되는 것을 평가하여야 한다. CSA N285.8-05 에는 이물질 프레팅 결함에 대해서는 선형파괴역학 기반한 개략적인 수식만이 제시된다. 본 연구에서는 이러한 이물질 프레팅 결함에 대해 2 차원 유한요소 해석과 일부 수정된 Kinectrics 사의 공학적 절차를 통해 이물질 프레팅 결함의 기하학적 특성이 좀더 상세히 고려된 탄성 응력집중계수 수식을 도출하였다. 도출된 수식을 적용한 결과와 3 차원 유한요소 해석 결과를 비교한 결과, 도출된 수식은 유한요소 해석과 잘 일치하는 결과를 얻을 수 있음을 확인하였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 춘계학술발표회요약집
• /
• pp.341-341
• /
• 2001

• 지질공학
• /
• 제1권1호
• /
• pp.68-84
• /
• 1991

A numerical analysis using Universal Distinct Element Code program for the nuclear waste disposal cavern has been performed for a typical Korean crystalline rock condition with same geometry of Swedish low and intermediate nuclear waste disposal repository(S.F.R). The stress concentration, displacement and safety factor for the typical single cross section of cavern, 5 caverns and a silo are analyzed.

• 대한기계학회논문집A
• /
• 제38권10호
• /
• pp.1163-1169
• /
• 2014

본 연구에서는 자동차 서스펜션 구조에 일반적으로 사용되는 용접부 형상에 대하여 굽힘 하중에 의한 피로수명을 예측할 수 있는 절차를 개발하였다. 이종 재료로 이루어진 실제 제품 용접 연결부의 피로수명 예측을 위해, 복잡한 형상의 제품을 단순화한 용접 시편을 설계하고 이에 대한 굽힘 피로 시험을 진행한 후 모멘트-피로수명(M-N) 선도를 제시하였다. 응력 집중에 의한 영향을 분석하기 위해 시편의 형상을 모델링 한 후 정적 하중에 대한 유한요소해석을 수행하여 균열 발생부의 응력을 구하고 응력-피로수명(S-N) 선도를 제시하였다. 유한요소해석을 통해 구한 응력과 이론 계산을 통해 구해준 응력을 이용하여 응력집중계수를 계산하였고, 응력집중부의 피로평가 방법 개선을 위해 보편적으로 사용되는 피로노치계수 평가법과 굽힘 피로 시험 결과를 비교 검토하였다. 그 결과, 이종 재질 용접 연결부의 정확한 피로 수명평가를 위해서는 기하형상을 고려한 피로노치계수 평가 분석뿐만 아니라 두 소재의 맞대기 용접 시편에 대한 피로 시험을 수행해 주어야 할 것으로 판단된다.

• Journal of Welding and Joining
• /
• 제32권2호
• /
• pp.37-42
• /
• 2014

In this study, non-load-carrying fillet welded joints fabricated using EH grade-steel are evaluated with the structural stress approach. The thickness effect was investigated by a study on welded steel joints with thickness ranging from 25 to 80mm. As-welded joint for main plate thickness of 25 to 80mm, the fatigue strength is reduced gradually. On the other hand, in case of main plate thickness of 25 to 80mm, the structural stress concentration factor increases gradually. As a result, for structural stress approach, thickness effect is not required for correction. Based on these results, a new evaluation fillet welded joint for fatigue design purposes has been proposed FAT 125.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.290-296
• /
• 2012

Cold-rolled carbon steel sheets are commonly used in railroad car or commercial vehicles such as the automobile. These are mainly fabricated by spot welding which is a kind of electric resistance welding. But fatigue strength of spot welding joint is lower than that of base metal due to high stress concentration at nugget edge of the spot welded part. And fatigue strength of them is especially influenced by not only geometrical and mechanical factors but also welding conditions of the spot welded joint. So for fatigue design of gas welded joints such as TS-type joints, it is necessary to obtain design information on stress distribution at the weldment as well as fatigue strength of spot welded joints. And also, the influence of the geometrical parameters of spot welded joints on stress distribution and fatigue strength must be evaluated. And analysis approach for fatigue test using design of experiment are evaluated optimum factor in TS-type welded joint and geometrical parameters of materials. Using these results, that factors applied to fundamental information for automation of fatigue design.

• 한국지반공학회지:지반
• /
• 제12권1호
• /
• pp.87-110
• /
• 1996

터널굴착시, 막장부근의 3차원 효과를 반영하기 위해 주로 경험적인 하중분담률 개념을 도입한 2차원 유한차분법 수치해석이 수행된다. 본 논문에서는 3차원 수치해석을 수행하고 그 해석 결과와 2차원 수치해석 결과를 비교함으로써 합리적인 하중분담률의 적용 가능성 및 막장 부근의 음력집중 문제를 규명하고자 하였다. 무지보 굴착길이, 초기지중응력, 지반종류, 단면크기와 터널심도등의 하중분담률에 주된 영향을 미치는 인자들에 대한 매개변수 연구를 수행하고, 그 결과를 토대로 서울지하철의 대표적인 단면에 대해 적용가능한 하중분담률을 추천하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.497-497
• /
• 2013

Semiconducting amorphous InGaZnO (a-IGZO) has attracted significant research attention as improved deposition techniques have made it possible to make high-quality a-IGZO thin films. IGZO thin films have several advantages over thin film transistors (TFTs) based on other semiconducting channel layers.The electron mobility in IGZO devices is relatively high, exceeding amorphous Si (a-Si) by a factor of 10 and most organic devices by a factor of $10^2$. Moreover, in contrast to other amorphous semiconductors, highly conducting degenerate states can be obtained with IGZO through doping, yet such a state cannot be produced with a-Si. IGZO thin films are capable of mobilities greaterthan 10 $cm^2$/Vs (higher than a-Si:H), and are transparent at visible wavelengths. For oxide semiconductors, carrier concentrations can be controlled through oxygen vacancy concentration. Hence, adjusting the oxygen partial pressure during deposition and post-deposition processing provides an effective method of controlling oxygen concentration. In this study, we deposited IGZO thinfilms at optimized conditions and then analyzed the film's electrical properties, surface morphology, and crystal structure. Then, we explored how to generate IGZO thin films using DC magnetron sputtering. We also describe the construction and characteristics of a bottom-gate-type TFT, including the output and transfer curves and bias stress instability mechanism.

• 대한조선학회논문집
• /
• 제52권5호
• /
• pp.372-379
• /
• 2015

The blade root fillets which have strong influences on the performance of propellers in the both structural and hydrodynamic points of view, are mechanical parts for smooth connection surface with a blade and a hub. A few related researches (Sabol, 1983; Kennedy, 1997) have noted that 3T-T/3 double radius section design would be suitable for reducing Stress Concentration Factor(SCF) and increasing Cavitation Inception Speed(CIS). In this paper, it is confirmed that this compound cross-section design has come close to the optimum solution in the shape optimization standpoint so that it could protect the propeller blade under the frequent and various loading cases. On that basis, we suggest the definite and simple fillet design methodology that has the cross-section with nT-T/n compound radius and elliptic shape which could sustain the given derivatives information as well as the offsets at the boundary and all inner region of the fillet surface. In addition, the result of design is presented in form of IGES file format in order to connect with NC machine seamlessly.