• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.76-82
• /
• 2015

A hybrid fiber-optic sensor system which combines fiber Bragg grating sensors and a Michelson interferometer has been constructed and evaluated for condition monitoring of large scale wind turbines. In order to measure multiple stresses applied to wind turbines such as strain, temperature and vibration, the system uses single broadband light source. It addresses both types of sensors, which simplifies the optical setup and enhances the cost-effectiveness of condition monitoring system. An athermal-packaged FBG is used to supply quasi-coherent light, of which coherence length is about 3.28mm, for the Michelson interferometer demodulation. Experimental results demonstrated that the proposed fiber-optic sensor system was capable of measuring strain and temperature with measurement accuracy of 1pm. Also 500~2000Hz vibration signals were successfully analyzed by applying FFT signal processing to interference signals.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3334-3338
• /
• 2012

본 연구는 프로펠러 주조시 사용되는 지그를 개선하기 위하여 수행된 것으로, 주조시 주형을 지지하는 강관 지그에 발생하는 응력을 실험적, 해석적인 방법을 사용하여 평가한 결과 주형의 높이방향 변형을 방지하기 위하여 사용된 수직 지그는 작용하는 응력수준이 낮고 주형 상부 지지대에 추가적으로 하중을 가하고 있기 때문에 주형에 적용할 필요가 없다. 또한 주형의 회전을 방지하기 위하여 수평방향으로 설치한 측면 강관 지그도 작용하는 응력수준이 낮아 부착할 필요가 없으며, 주형 모서리 부분에 설치한 강관 지그는 압축력이 크게 작용하는 상부 주형 강관 지그를 제외하고 하부 주형에 설치된 강관 지그는 적용할 필요가 없다는 것을 알 수 있다.

• 비파괴검사학회지
• /
• 제19권1호
• /
• pp.16-24
• /
• 1999

잔류응력은 공학적 구조물에 결함을 야기하는 유해한 응력이므로 산업현장에서는 이를 측정하기 위한 많은 관심을 가지고 있다. 현재 잔류응력 측정은 일반적인 방법을 사용하고 있지만 이러한 방법들은 어느정도 문제점을 내포하고 있다. 그러므로 레이저 스페클 간섭법에 유한요소법과 점 가열법을 혼합하여 산업 현장에 유해한 잔류응력을 측정할 수 있는 새로운 기법을 개발하였다. 이 기법에서 사용된 레이저 스페클 간섭계는 측정 시편의 응력이 풀릴 때의 면내 변형을 측정하기 위해서 사용되어 졌으며, 유한요소법은 응력 풀림을 위한 가열부의 온도와 그 밖의 변수들을 결정하기 위해서 사용되어 졌다. 잔류응력은 측정하고자 하는 부위의 가열 냉각에 의한 변형률에 의해 결정되어지며, 이에 대한 간단한 모델링을 제시하였다. 또한 본 실험은 변형의 3차원 정량화를 수행하기 위해서 레이저 스페클 간섭계의 전자 광학적 기법 중의 하나인 위상이동법을 이용하여 수행되어졌다.

• Elastomers and Composites
• /
• 제42권4호
• /
• pp.201-208
• /
• 2007

본 연구에서는 충전된 고무재료의 온도 변화에 대한 치수 안정성을 고찰하기 위해 카본블랙 또는 실리카가 충전된 NR과 SBR의 열변화시 발생하는 수축력과 팽창력을 측정하였다. 일정 길이로 인장된 시편의 온도를 올렸을 때 고무사슬의 엔트로피적 변화에 의해 수축력이 발생하였다. 카본블랙이나 실리카가 첨가된 NR의 경우 충전제 함량이 증가함에 따라 최대 열수축력 값이 감소하였으나, SBR의 경우는 30 phr 함량에서 미충전 고무보다 높은 열수축력 값을 보였다. 압축된 시편의 열팽창력 측정의 경우, 카본블랙을 첨가한 NR의 열팽창력은 거의 변화가 없었으나, SBR은 카본블랙 양의 증가와 함께 최대 팽창력 값이 증가하였다. 실리카를 첨가했을 경우 NR, SBR시편 모두 첨가량이 증가할수록 최대 열팽창력 값이 증가하였다.

• Composites Research
• /
• 제26권3호
• /
• pp.182-188
• /
• 2013

본 연구의 목적은 silorane 기질의 치아 수복용 복합레진의 중합수축과 수축응력의 동력학을 평가하고 전통적인 methacrylate 기질의 복합레진과 비교하기 위함이다. 두 종의 methacrylate 기질의 복합레진(Z250, Z350 flowable)과 silorane 기질 복합레진(P90)이 사용되었다. 아르키메데스 원리를 응용해 자체 제작한 중합수축 측정 장치를 사용하여 광중합 중 일어나는 복합레진의 체적 중합수축을 측정하였고 스트레인게이지로 중합수축응력을 측정하였다. Silorane 기질 복합레진인 P90의 중합수축과 최대 중합수축률이 가장 낮았고 methacrylate 기질 복합레진인 Z350 flowable이 가장 높았다. Methacrylate 기질의 복합레진과 비교하여 silorane 기질의 복합레진 P90이 최대 수축률에 이른 시간은 더 길었고 중합수축응력은 낮았다.

• 한국세라믹학회지
• /
• 제35권8호
• /
• pp.813-818
• /
• 1998

A simple method to measure the elastic modulus E and Poisson's ratio v of diamod-like carbon (DLC) films deposited on Si wafer was suggested. Using the anisotropic etching technique of Si we could make the edge of DLC overhang free from constraint of Si substrate. DLC film is chemically so inert that we could not on-serve any surface damage after the etching process. The edge of DLC overhang free from constraint of Si substrate exhibited periodic sinusoidal shape. By measuring the amplitude and the wavelength of the sinu-soidal edge we could determine the stain of the film required to adhere to the substrate. Since the residual stress of film can be determine independently by measurement of the curvature of film-substrate com-posite we could calculated the biaxial elastic modulus E/(1-v) using stress-strain relation of thin films. By comparing the biaxial elastic modulus with the plane-strain modulus E/(1-{{{{ { v}^{2 } }}) measured by nano-in-dentation we could further determine the elastic modulus and Poisson's ratio independently. This method was employed to measure the mechanical properties of DLC films deposited by {{{{ { {C }_{6 }H }_{6 } }} rf glow discharge. The was elastic modulus E increased from 94 to 169 GPa as the {{{{ { V}_{ b} / SQRT { P} }} increased from 127 to 221 V/{{{{ {mTorr }^{1/2 } }} Poisson's ratio was estimated to be abou 0.16∼0.22 in this {{{{ { V}_{ b} / SQRT { P} }} range. For the {{{{ { V}_{ b} / SQRT { P} }} less than 127V/{{{{ {mTorr }^{1/2 } }} where the plastic deformation can occur by the substrate etching process however the present method could not be applied.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제45권4호
• /
• pp.199-206
• /
• 2019

Objectives: In mandibular edentulism, the treatment option with a two-interforaminal implant-retained bridge and a removable partial denture is rarely evaluated in literature. The aim of this in vitro study was to evaluate the stress distribution of this treatment option by comparing it with traditional treatment options with interforaminal implants in the edentulous mandible. Materials and Methods: Two interforaminal implants were placed in a formalin-fixed cadaver mandible, and overdentures with three different types of attachments were fabricated: (1) two ball attachments and an overdenture, (2) a Dolder bar and an overdenture, and (3) screw-retained two-implant inter-canine porcelain fused to a metal bridge and an implant-assisted removable denture (IARD) with precision attachments. Three biting conditions were generated for each denture type, and the strains were documented under vertical loading of 100 N. Results: The calculated strain values from measured strains in all measurement sites and loading conditions for the screw-retained two-implant intercanine porcelain fused to a metal bridge and a cast framework partial denture with precision attachments situation were lower than in the other scenarios (P<0.05). Conclusion: Within the limitations of the present study, it can be concluded that an IARD may be a reasonable and valuable alternative to ball attachments or a bar in two interforaminal implants, especially when the patients prefer to be able to show their teeth even when they take out their removable dentures.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.19-24
• /
• 2011

The operational efficiency of domestic gas turbine is about 25% and it is now in the trend of the gradual growth in spite of the severe temperature, frequent starting and shutdown according to the environmental management and the energy-efficient use. Rotor bolts of gas turbine in power plants have been the cause of defects because these gas turbines have been operated for a long time under the high pressure and temperature environment experiencing the aging change and stress concentration of the bonded part. The connection parts of the bolt revealed various failure shape and these parts were elongated under very low pressure when operated in the relaxed condition. The cause is in the lack of the metal distribution in the bottle lack area and the cap screw of the bolt is broken totally in case that the nut is fastened in most cases. Gas turbine rotor bolts are connected to the rotor wheel and these bolts caused the vibration, the bulk accident of the rotor in the event that the coupling power among these bolts was relaxed. Therefore, we would like to evaluate the soundness of the main part of the gas turbine rotor bolt through the measurement of the inner condition change along with the mechanic deterioration and temperature, stress in the gas turbine rotor material.

• 소성∙가공
• /
• 제27권5호
• /
• pp.301-313
• /
• 2018

In this paper, tensile test was performed on pure titanium sheet (CP Ti sheet) with HCP structure in each direction to evaluate mechanical and surface properties and analyze microstructural changes during plastic deformation. We also evaluated forming limits of Ti direction in dome-type punch stretching test using a non-contact three-dimensional optical measurement system. As a result, it was revealed the pure titanium sheet has strong anisotropic property in yield stress, stress-strain curve and anisotropy coefficient according to direction. It was revealed that twinning occurred when the pure titanium sheet was plastic deformed, and tendency depends differently on direction and deformation mode. Moreover, this seems to affect the physical properties and deformation of the material. In addition, it was revealed the pure titanium sheet had different surface roughness changes in 0 degree direction and 90 degree direction due to large difference of anisotropy, and this affects the forming limit. It was revealed the forming limit of each direction obtained through the punch stretching test gave higher value in 90 degree direction compared with forming limit in 0 degree direction.

• Structural Engineering and Mechanics
• /
• 제75권5호
• /
• pp.595-605
• /
• 2020

In this study, the flexural behaviors of full-scale prestressed concrete box girders are experimentally investigated. Four girders were fabricated using two types of concrete (compressive strengths: 50 MPa and 70 MPa) and tested under four-point bending until failure. The measured parameters included the deflection, the stress and strain in concrete and steel bars, and cracks in concrete. The measurement results were used to analyze the failure mode, load-bearing capacity, and deformability of each girder. A finite element model is established to simulate the flexural behaviors of the girders. The results show that the use of high-performance concrete and reasonable combination of prestressed tendons could improve the mechanical performance of the box girders, in terms of the crack resistance, load-carrying capacity, stress distribution, and ductility.