• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1003-1008
• /
• 2001

It is recently reported that bond failure can be initiated in the region where maximum bending moment and shear force is acted by accompanying shear deformation after flexural crack in full-scale RC beams strengthened by CFRP. Such a shear deformation effect causing bond failure is relatively little in the case of small-scale specimens. So, additional reinforcing details to the critical beam section where maximum moment and shear were acted is required to prevent the bond failure caused by the shear deformations. The U-type wrapping methods by CFRP to the critical beam section is proposed and tested in this paper. Also, the applicability of design bond strength derived from the tests of small-scale beam was investigated by the full-scale RC beam strengthened by CFRP.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.817-822
• /
• 2002

In this paper, the strengthening analysis by strut-tie model for strengthened shear failed RC deep beam by the so-called the Steel Clamping Unit (SCU), which is a strengthening equipment, is carried out. The analysis considers the span-to-depth ratio, the existence of prestressing and stirrup, the shape of shear crack, and the strengthening position of the SCU. Based on analytical results, optimized strengthening analysis and design are carried out by investigating the behavior of the strengthened deep beams. The comparison between analytical results and experimental results shows that optimum strengthening effect by the SCU can be obtained when compressive strut zone created by SCU is away from major shear crack of the beam as far as possible.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.470-473
• /
• 2006

Past experiences from recent earthquakes indicate that shear failures of beam-column connections were one of the main reasons causing significant damages and collapses of RC structures subjected to earthquake loadings. Many researchers and engineers have conducted to propose an effective way to improve the joint shear strength of RC connections. This paper presents an analytical model for the RC exterior beam-column joints strengthened with CFRP sheets. In the analytical model, the effect of shear behavior of the RC beam-column joint, bond slip of the beam longitudinal reinforcements and CFRP sheets were considered and incorporated into the non-linear structural analysis program. Final analytical results were compared with those from the experiment of eight exterior RC beam-column specimens. The analytical results showed that the developed connection model is very useful to investigate the hysteretic joint behavior and overall load-displacement response of the RC beam-column connections strengthened with CFRP sheets.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.621-626
• /
• 1997

Recently, TYFO glassfibers have been used for strengthening n aged RC bridge slabs because of low material cost and easy repairing work. The purpose of this study is to experimentally and analytically investigate the effect of TYFO glassfibers for enhancing the capacity of aged RC bridge slabs. Tes result shows that yield and ultimate strength of RC slabs with TYFO are increased as 11~18% and 25~35% comparing with those for RC slabs without TYFO, respectively, Also, ductility of RC slabs strengthened with TYFO have been significantly increased. Further tests have been performing on aged RC bridge slabs strengthened with carbon fiber strips.

• Structural Engineering and Mechanics
• /
• v.53 no.6
• /
• pp.1067-1081
• /
• 2015

This study investigates structural and mechanical behaviors of RC (Reinforced concrete) beams strengthened with tapered CFRP (Carbon fiber reinforced polymer) sheets having various configurations. Toward this goal, experiments are performed on RC beams strengthened with four layers of CFRP sheets and each layer of the CFRP is prepared to have different length. Experimental results show that tapered CFRPs have better strengthening effect than non-tapered CFRP sheets and maximum loads of the beams with tapered CFRPs are governed by the length of first CFRP layer rather than total length of CFRP layers. In addition, analyses are performed using FE (Finite Element) models including cohesive elements to predict debonding behaviors between FRP and concrete elements. The predicted results from the FE models show good agreement with the experimental results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.473-476
• /
• 2004

Carbon Fiber Reinforced Polymer(CFRP) composites are widely applied to strengthen deteriorated concrete structures. This paper presents the experimental results of the performance of reinforced concrete(RC) beams strengthened with Near Surface Mounted T-shape CFRP. Simple beams with 3m span length were tested to investigate the effect of CFRP reinforcement shapes on the flexural behavior of strengthened RC beams. The test results were analyzed with the special emphasis on the failure mode and the maximum load.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.521-526
• /
• 2001

The flexural behavior of a strengthened beam that is a reinforced concrete beam with externally bonded carbon fiber sheets, is theoretically and experimentally investigated. A rectangular beam having a width of 20cm depth of 30cm and effective depth of 25cm is chosen. In order to have a variety of beams analyzed, three reinforcement ratios are chosen for the analysis: 1)$\frac{1}{2}$$\rho$$_{max}$, which is the most suitable reinforcement ratio for deflection consideration and the highest reinforcement ratio for practical designing beams as well; 2)$\rho$$_{max}$, which is the lowest reinforcement ratio for design purposes; and 3)the reinforcement ratio halfway from 1) and 2). Carbon fiber sheets with width of 15cm are externally bonded at the bottom fiber of the beam. The effect of the amount of carbon fiber sheets varying from 1 to 4 plies on the flexural capacity of the strengthened beam are also examined. Yield loads, ultimate loads, and flexural rigidities of the strengthened beam from the experimental results are composed with theoretical ones.nes.

• Steel and Composite Structures
• /
• v.15 no.6
• /
• pp.605-621
• /
• 2013

CFRP strips are widely used nowadays for repair/strengthening or capacity increase purposes. Sharp bending at the ends of the CFRP strips is frequently encountered at these applications. In this study, Reinforced Concrete (RC) beam specimens that were produced with 10 MPa compression strength concrete were strengthened by using bonded CFRP strips with end anchorages to tension region. The parameters that were investigated in this study are the width of the strip, the number of applied fan anchorages and whether additional layer of CFRP patch is used or not at the strip ends. Specimens were strengthened with 100 mm wide CFRP strips with one or two anchorages at the ends. In addition CFRP patch with two and three anchorages at the ends were tested for investigating the effect of the patches. Specimens that were strengthened with three anchorages at the ends with patches were repeated with 60 and 80 mm wide CFRP strips. The most successful result was obtained from the specimen that was strengthened with 80 mm wide CFRP strips with 3 end anchorages and patches among the others at the experimental program. The numbers of anchorages that were applied to ends of CFRP strips were more effective than the width of the CFRP strips onto strength and stiffness of the specimens. Due to limited space at the ends of the strips at most three anchorages could be applied.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.2 s.20
• /
• pp.123-129
• /
• 2006

Recently, many researches have been conducted about reinforced concrete structures strengthened with FRP plates. In case of structures strengthened with FRP plates, the issue of premature debonding FRP plate has been raised through many previous researches. The purpose of this paper is what structural behavior and flexaural capacity of reinforced concrete beams which are strengthened for flexure is investigated about the using secondary ironware in the method of external bonded CFRP plate, and the method of near surface mounted CFRP-Rod. Also, in order to evaluate flexural capacity, experiments of the reinforced concrete beams with exteranl bonded CFRP plate and near surface mounted CFRP-Rod have been compared and investigated.

• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.25-43
• /
• 2016

This paper presents the results of an experimental study investigating the effects of anchorage systems used in externally bonded steel plates on the strength and ductility of reinforced concrete structures. In the literature, diagonal steel plates bonded to frames were designed to be more flexible than the connections to eliminate the possible effect of the connection flexibility. However, to better evaluate the performance of the strengthened structures, the strength and behavior of connections should also be considered. The purpose of this study was to experimentally investigate the effects of different connection types of steel plates bonded to the frame using anchors on the strengthened RC structures. For this purpose, eleven specimens were designed to simulate the interior and exterior connection behavior. Two of these were used as the control beams and remaining nine for the investigation of the functionality of the end steel plates. Experimental results show that the load carrying capacity of the strengthened beams is directly related to the connection types of the steel plates. For the interior connections, L-shaped end plates that were strengthened using steel anchors must have adequate stiffness to prevent its shape. While, for the exterior connections, the connection with three anchors carried more load than the other exterior connections.