• Korean Journal of Materials Research
• /
• v.12 no.7
• /
• pp.560-567
• /
• 2002

Titanium (Ti) is a bioinert material and has lower elastic coefficient and better strength/volume property than other metals. Ferroelectric materials show alignment of positive and negative charges by poling treatment. This study was purposed to develop a new implant system by combining the advantages of Ti and ferroelectric property of $BaTiO_3$ (BTO). It was performed with the assumption that the $Ca^{2+ }$ ions would be easily attracted on negatively charged surface and the attracted cation might behave as nuclei for bone-like crystal growth in biological solutions. A ferroelectric BTO thin film on Ti was fabricated and the effect of poling treatment on the improvement of calcium phosphate (Ca-P) formation in biological solutions was evaluated. After immersion in Eagle’s minimum essential media (MEM) solution, NaCl was formed on Ti, and Ca-P layer containing NaCl was formed on Ti-O. Weak and sparse Ca-P layers were formed on BTO, while thick, homogeneous, and dense Ca-P layer was formed on negatively polarized BTO (N-BTO), which was confirmed by FE-SEM and EDX. In summary, these results demonstrate that poling the ferroelectric BTO surface negatively is effective for the formation of Ca-P layer in MEM solution, and that N-BTO coating on Ti could be used as a possible alternative method for enhancing the osseointegration of the implants.

• Journal of Periodontal and Implant Science
• /
• v.38 no.4
• /
• pp.595-602
• /
• 2008

Purpose: Ti-6Al-4V alloy is widely used as an implant material because of its good biocompatibility and good mechanical property compared with commercial pure titanium. Otherwise, toxicity of aluminum and vanadium in vivo has been reported. Ti-8Ta-3Nb alloy is recently developed in the R&D Center for Ti and Special Alloys and it was reported that this alloy has high mechanical strength, no cytotoxicity and similar biocompatibility to commercial pure titanium, but many studies are needed for its clinical use. In these experiment, we carried out different surface treatment on each Ti-8Ta-3Nb alloy disks, then cultured cell on it and assessed biological response. Materials and Methods: cpTi, Ti-6Al-4V, Ti-8Ta-3Nb alloy disks were prepared and carried out sandblasting and acid etching (SLA) or alkali-heat treatment (AH) on the Ti-8Ta-3Nb alloy disks. We cultured primary rat calvarial cells on each surface and assessed early cell attachment and proliferation by scanning electron microscopy, cell proliferation, alkaline phosphatase activity. Result: The rates of cell proliferation on the cpTi, Ti-8Ta-3Nb AH disks were higher than others (p<0.05) and alkaline phosphatase activity was significantly enhanced on the Ti-STa-8Nb AH disks(p<0.05). Conclusion: Most favorable cell response was shown on the Ti-8Ta-3Nb AH surfaces. It is supposed that alkali-heat treatment of the Ti-8Ta-3Nb alloy could be induced earlier bone healing and osseointegration than smooth surface.

• Asian-Australasian Journal of Animal Sciences
• /
• v.11 no.5
• /
• pp.463-469
• /
• 1998

Factor analysis was applied as a multivariate statistical technique to official genetic evaluations of type classification traits for 1,265,785 Holstein cows and 10,321 sires computed from data collected between August 1982 and June 1994 in Canada. Type traits included eighteen linear descriptive traits and eight major score card traits. Principal components of the factor analysis showed that only five factors explain the information of the genetic value of linear descriptive traits for both cows and sires. Factor 1 included traits related to mammary system, like texture, median suspensory, fore attachment, fore teat placement and rear attachment height and width. Factor 2 described stature, size, chest width and pin width. These two factors had a similar pattern for both cows and sires. In constrast, Factor 3 for cows involved only bone-quality, while in addition for sires, Factor 3 included foot angle, rear legs desirability and legs set. Factor 4 for cows related to foot angle, set of rear leg and leg desirability, while Factor 4 related to loin strenth and pin setting for sires. Finally, Factor 5 included loin strength and pin setting for cows and described only pin setting for sires. Two factors only were required to describe score card traits of cows and sires. Factor 1 related to final score, feet and legs, udder traits, mammary system and dairy character, while frame/capacity and rump were described by Factor 2. Communality estimates which determine the proportion of variance of a type trait that is shared with other type traits via the common factor variant were high, the highest ${\geq}$ 80% for final score, stature, size and chest width. Pin width and pin desirability had the lowest communality, 56% and 37%. Results indicated shifts in emphasis over the twelve-year period away from udder traits and dairy character, and towards size, scale and width traits. A new system that computes fmal score from type components has been initiated.

• Archives of Plastic Surgery
• /
• v.39 no.2
• /
• pp.113-117
• /
• 2012

Background : Nasal pyramid fractures accompanied by saddle nose deformities are not easily corrected by closed reduction. We used an absorbable plate as a perpendicular strut to support the collapsed "keystone area" and obtained good results. Methods : Between September 2008 and June 2011, 18 patients who had nasal pyramid fractures with saddle nose deformities underwent surgery. Pre- and postoperative facial computed tomographic images and photographs were taken to estimate outcomes. The operative technique included the mucoperichondrial dissection of the nasal septum, insertion of an absorbable plate prepared to an appropriate length to support the "keystone area", and fixation of the absorbable plate strut to the cartilaginous septum. Results : Functional and esthetic outcomes were satisfactory in all patients. Eleven patients assessed the postoperative appearance of the external nose as 'markedly improved' and 7 patients as 'improved'. The 5 surgeons scored the results as a mean of 4.5 on a 5-point scale. Conclusions : The use of an absorbable plate as a perpendicular strut requires no additional procedures because the plate is gradually absorbed. The mechanical strength provided by a buttress between the "keystone area" and the maxillary crest lasts for a long time before the strut is absorbed.

• Computers and Concrete
• /
• v.3 no.4
• /
• pp.213-233
• /
• 2006

Over the past years techniques for non-linear analysis have been enhanced significantly via improved solution procedures, extended finite element techniques and increased robustness of constitutive models. Nevertheless, problems remain, especially for real world structures of softening materials like concrete. The softening gives negative stiffness and risk of bifurcations due to multiple cracks that compete to survive. Incremental-iterative techniques have difficulties in selecting and handling the local peaks and snap-backs. In this contribution, an alternative method is proposed. The softening diagram of negative slope is replaced by a saw-tooth diagram of positive slopes. The incremental-iterative Newton method is replaced by a series of linear analyses using a special scaling technique with subsequent stiffness/strength reduction per critical element. It is shown that this event-by-event strategy is robust and reliable. First, the model is shown to be objective with respect to mesh refinement. Next, the example of a large-scale dog-bone specimen in direct tension is analyzed using an isotropic version of the saw-tooth model. The model is capable of automatically providing the snap-back response. Subsequently, the saw-tooth model is extended to include anisotropy for fixed crack directions to accommodate both tensile cracking and compression strut action for reinforced concrete. Three different reinforced concrete structures are analyzed, a tension-pull specimen, a slender beam and a slab. In all cases, the model naturally provides the local peaks and snap-backs associated with the subsequent development of primary cracks starting from the rebar. The secant saw-tooth stiffness is always positive and the analysis always 'converges'. Bifurcations are prevented due to the scaling technique.

• Animal Bioscience
• /
• v.37 no.4
• /
• pp.555-566
• /
• 2024

Objective: This study aimed to assess the genetic parameters and accuracy of genomic predictions for twenty-four linear body conformation traits and overall conformation scores in Korean Holstein dairy cows. Methods: A dataset of 2,206 Korean Holsteins was collected, and genotyping was performed using the Illumina Bovine 50K single nucleotide polymorphism (SNP) chip. The traits investigated included body traits (stature, height at front end, chest width, body depth, angularity, body condition score, and locomotion), rump traits (rump angle, rump width, and loin strength), feet and leg traits (rear leg set, rear leg rear view, foot angle, heel depth, and bone quality), udder traits (udder depth, udder texture, udder support, fore udder attachment, front teat placement, front teat length, rear udder height, rear udder width, and rear teat placement), and overall conformation score. Accuracy of genomic predictions was assessed using the single-trait animal model genomic best linear unbiased prediction method implemented in the ASReml-SA v4.2 software. Results: Heritability estimates ranged from 0.10 to 0.50 for body traits, 0.21 to 0.35 for rump traits, 0.13 to 0.29 for feet and leg traits, and 0.05 to 0.46 for udder traits. Rump traits exhibited the highest average heritability (0.29), while feet and leg traits had the lowest estimates (0.21). Accuracy of genomic predictions varied among the twenty-four linear body conformation traits, ranging from 0.26 to 0.49. The heritability and prediction accuracy of genomic estimated breeding value (GEBV) for the overall conformation score were 0.45 and 0.46, respectively. The GEBVs for body conformation traits in Korean Holstein cows had low accuracy, falling below the 50% threshold. Conclusion: The limited response to selection for body conformation traits in Korean Holsteins may be attributed to both the low heritability of these traits and the lower accuracy estimates for GEBVs. Further research is needed to enhance the accuracy of GEBVs and improve the selection response for these traits.

• The Korean Journal of Food And Nutrition
• /
• v.22 no.4
• /
• pp.577-586
• /
• 2009

Aging is associated with decreased energy expenditure, thermogenesis and energy requirements. Maintenance of physical fitness of the elderly has been reported to reduce the rate at which the basal metabolic rate, muscle strength, skeletal muscle mass and bone density deteriorate. Skeletal muscle disease is known to increase the risk of physical disability and psychological problems. This study was conducted to investigate changes in disability, emotional problems, body compositions, obesity indices and nutrient intake levels according to physical fitness with the elderly in rural areas. According to the results, physical fitness was negatively related with Activities of Daily Living(ADL, p<0.05), Instrumental Activities of Daily Living(IADL, p<0.001), Body Mass Index(BMI, p<0.001) and abdominal obesity(p<0.05), while it showed a positive correlation with the General Self Efficacy Scale(GSES)(p<0.001) and nutrient intake(p<0.05). When changes in these factors were compared according to the range of quartile of the Fullerton Advanced Balance Scale(FAB Scale), GSES(Q1=35.3, Q2=43.5, Q3=53.2, Q4=51.9, p<0.001), BMI(Q1=36.1%, Q2=34.7%, Q3=33.2%, Q4=28.6%, p<0.01), abdominal obesity(Q1=1.02, Q2=0.99, Q3=0.97, Q4=0.94, p<0.001) and nutrient intake(Q1=71.1%, Q2=75.4%, Q3=80.6%, Q4=80.2%, p<0.05) differed significantly. Taken together, these results suggested that better physical fitness would lead to a reduction in negative factors including physical disability and obesity indices, but to an increase in positive factors such as GSES and nutrient intake. The results of this study are expected to be used as basic data for the development of programs to promote the health of the elderly in a local society.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.9
• /
• pp.1299-1304
• /
• 2005

An experiment was conducted to study the production performance of broiler breeder females (25 to 40 weeks of age) fed either reference diet or low non-phytate phosphorus (NPP) diet with or without microbial phytase (500 FYT/kg) supplementation. A weighed (160 g/b/d) quantity of feed from each diet was offered daily to 40 replicates of one bird each housed in California type cage having individual feeders. Each cage was considered as a replicate. A continuous 16-h light per day was provided using incandescent bulbs. Body weight, egg production, egg weight, feed per egg mass, egg specific gravity, egg breaking strength, shell thickness, tibia ash and serum Ca and protein concentrations were not affected by reducing the NPP level from 0.30 to 0.18% in the broiler breeder diet. Supplementation of phytase (500 FYT/kg) enzyme to the diet containing 0.18% NPP had no added advantage on any of the above production parameters. The serum inorganic P was increased significantly (p<0.05) by either enhancing the NPP content from 0.18 to 0.30% or supplementing phytase @500 FYT/kg to the diet containing low P which were found comparable. Retention of Ca and P was positive on all the diets. P retention decreased significantly (p<0.05) with either increase in NPP content or phytase supplementation in the diet. Neither NPP nor phytase supplementation influenced bone mineralization in terms of tibia ash and strength. The hatchability was not influenced by either increasing the NPP content or supplementing the enzyme phytase. Similarly, the P concentration in the egg yolk and day old chick, day old and 14th day body weight and leg score was not altered by increasing the level of NPP or supplementing phytase enzyme. The mortality was within the normal limits in all the three dietary groups. Thus, it can be concluded that 0.18% NPP (288 mg NPP intake/b/d) in the broiler breeder' diet is adequate in sustaining the optimum performance from 25 to 40 wks of age. Enhancing the NPP content or supplementation of phytase (500 FYT/kg diet) to diet containing 0.18% NPP had no added advantage on performance.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.1
• /
• pp.149-156
• /
• 2018

Objective: Broilers show clear preference towards red color light (RL). However setting of an optimum light intensity is difficult since dim intensities that favor growth reduce welfare. This experiment was conducted to test the most effective RL intensity regimen (Dim [5 lux; DI] vs high [320 lux; HI]) in combination applied at different growth stages that favors for both performance and welfare. Methods: Complete randomize design was adopted with 6 replicates. Treatments were; T1 = early DI (8-21 d)+latter HI (22-35 d); T2 = early DI (8-28 d)+latter HI (29-35 d), T3 = early HI (8-21 d)+latter DI (22-35 d), T4 = early HI (8-28 d)+latter DI (29-35 d) and T5 = control (white light; WT) (8-35 d) at medium intensity (20 lux). Body weight (BW), weight gain (WG), water/feed intake and ratio, feed conversion ratios (FCR) were assessed. Common behaviours (15) were recorded by scan sampling method. Lameness, foot pad dermatitis, breast blisters, hock burning damage were assessed as welfare parameters. Fear reactions were tested using Tonic Immobility Test. Ocular and carcass evaluations were done. Meat and tibiae were analyzed for fat and bone ash respectively. Results: On 35 d, the highest BW ($2,155.72{\pm}176g$), WG ($1,967.78{\pm}174g$) were recorded by T2 compared to WT ($BW_{WT}=1,878.22{\pm}155$, $WG_{WT}=1,691.83{\pm}160$). But, application of RL, either DI, or HI during early/latter stage had no significant effect on FCR. Under HI, birds showed much higher active behaviours. DI encourages eating. Though LI changed from DI to HI, same trend could be seen even under HI. The highest leg strength ($218.5{\pm}120s$) was recorded by T2. The lowest leg strength ($64.58{\pm}33s$) and the highest ocular weight ($2.48{\pm}1g$) were recorded by T1. Significantly (p<0.05) the highest skin weight ($162.17{\pm}6g$) but the lowest fat% in meat ($13.03%{\pm}5%$) was recorded by T2. Conclusion: Early exposure to DI-RL up to 28 days followed by exposure to HI-RL is the most favorable lighting regimen for optimizing production, better welfare of broilers and improving health benefits of meat.

• Journal of the Korean Arthroscopy Society
• /
• v.3 no.1
• /
• pp.30-34
• /
• 1999

We report the case of a 30-year-old man who was presented with transient calcification on the graft shortly after anterior cruciate ligament(ACL) reconstruction using a autogenous bone patellar tendon. The patient underwent ACL reconstruction with two incisional technique and six month later, calcific density was seen radiologically around the graft. On postoperative 13 months follow-up radiographic films, the calcific density disappeared. After two months of operation, Lachman and pivot shift test were negative and one millimeter side to side difference was detected in KT-1000 with 20 Ibs strength. But 6 months after the reconstruction, mild anterior instability was detected with the calcific density around the grafted tendon. However the anterior stability was recovered according to the disappearance of calcific density.