• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.3
• /
• pp.39-47
• /
• 2015

In this study, the properties of strength and drying shrinkage of alkali-activated slag cement (AASC) with magnesium oxide (MgO) contents between 0 and 16 wt% were investigated. The ground granulated furnace blast slag (GGBFS) was activated by potassium hydroxide (KOH) and dosage of activator was 2M and 4M. The MgO was replaced with 2% to 16% of GGBFS by weight. The water-binder ratio (w/b) was 0.5. In the result, the higher MgO content leads to a slightly higher degree of reaction and thus to a higher compressive strength at all ages. The compressive strength and ultra sonic velocity (UPV) increased with increases MgO contents. The drying shrinkage of AASC was decreased as the contents of MgO increases. The results from SEM confirmed that there were densified reaction product of higher MgO content specimens.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.294-300
• /
• 2001

The effectiveness of bottom ash on the mechanical and physical properties of Controlled Low-Strength Material(CLSM) is investigated in this study, CLSM is defined by the ACI Committee 229 as a cementitious material that is in a flowable state at the time of placement and having a specified compressive strength of 83 kgf/$\textrm{cm}^2$ or less at the age of 28 days. This study was undertaken on the use of bottom ash as a fine aggregate in CLSM. Four different levels of bottom ash with fly ash contents, 25%, 50 %, 75%, 100%, are investigated. Laboratory test results conclude that inclusion of bottom ash increases the demand for mixing water in obtaining the required flow. However, the sand was reduced because it was adjusted to maintain a constant total volume. Miかe proportions were developed for producing CLSM at three 28-day strength levels: removal with tools (less than 7 kgf/$\textrm{cm}^2$), mechanical means (less than 20 kgf/$\textrm{cm}^2$), and power equipment (less than 83 kgf/cm\`). The physical and mechanical properties supports the concept that by-product bottom ash can be successfully used in CLSM.

• Journal of the Korean GEO-environmental Society
• /
• v.3 no.2
• /
• pp.23-33
• /
• 2002

Examined a practical use possibility of paper fly ash that is industrial by-product as a stabilization/hardening agent. Performed unconfined compression test, scanning electron microscopy and pH analysis etc. for 100% paper fly ash-soil mixtures and each paper fly ash-soil mixtures that add cement as the second addition and sulfate component of small quantity for strength promotion and so on. In all cases, strength of admixtures increased according as curing time and mixing ratio increases but almost strength is revealed at mixing early and expressed maximum strength increase efficiency at mixing ratio 9% with raw soil. Compare with the case that use paper fly ash only, in case of cement amount 10~30% was included in paper fly ash, strength of admixtures increases two times and 40% was included, that increases from five to eight times.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.685-688
• /
• 2008

Concrete is strong on the compressive property, but weak on the tensile and flexural properties. To improve these problems, the reinforcing bar is used in concrete. But porous concrete with steel fiber has a weak point when exposed to air, because porous concrete has the vast continuous void on its inside and steel fiber is easily rusted by air. For these reasons, this study investigated the void ratio, compressive strength, bending strength and bending toughness as steel fiber mixing ratio and target void ratio. From test results, actual void ratio and strength properties increased as the mixing ratio of steel fiber increase. In case the mixing ratio of steel fiber over the fixed ratio, strength is decreased. And from the toughness evaluation, compared to the porous concrete which isn't mixed with steel fiber, the deflection variation efficiency is remarkably improved. Consequently we can confirm the possibility of porous concrete with steel fiber for the secondary product and pavement material to improve strength and bending resistance efficiency.

• Journal of Distribution Science
• /
• v.17 no.1
• /
• pp.105-115
• /
• 2019

Purpose - Previous research has shown that a very high level and a very low level of job scope can both be more stressful than intermediate levels of job scope. This study investigates the potential positive and negative effects of the number of accounts handled by sales personnel. The primary objective of this paper is to examine how the number of accounts salespeople handle affects their stress and performance. Research design, data, and methodology - This research conducted the data collection using a survey of salespeople in the pharmaceutical industry. I sent the survey to 420 salespeople, and received 318 usable responses. To assess measurement reliability and validity, I ran an exploratory and confirmatory factor analysis. I also employed structural equation modeling (SEM) to test all hypothesized effects in AMOS and also measured the interaction variable using Ping's (1996) approach. Results - These results show that there are linear and non-linear effects of the number of accounts handled by the salesperson on both role ambiguity and role conflict. First, the number of accounts handled by a salesperson is positively related to role ambiguity and role conflict. Second, the effect of the number of accounts handled on role ambiguity and role conflict decreases as the number of accounts handled by the salesperson increases. Third, as accounts increase from a low level, role stress increases; when the number of accounts reaches an optimal level, role stress decreases; and when the number of accounts increases to a high level, it can be detrimental to the salesperson's role stress. Fourth, while product complexity is positively related to role ambiguity, brand strength is negatively related to both role ambiguity and role conflict. Fifth, the greater the brand strength, the weaker the relationship will be between the number of accounts handled and salesperson role ambiguity. Finally, role ambiguity is positively related to salesperson performance. Conclusion - Too much and too little accounts increase the role ambiguity and role conflict of salespersons. Managers should identify the complex effect of the number of accounts handled by salespeople. Also, when products are complex, managers should provide training to eliminate any complex processes and complex information. These results suggest ways to decrease salespersons' role stress by ensuring an optimal level of the number of accounts and brand strength.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.4
• /
• pp.315-327
• /
• 2021

Purpose of this study is reviewing the use method for the sawdust (sawmilling by-product) and rice husk (Agriculture by-product) by adding charcoal, an eco-friendly material. Mixed composite boards were manufactured with those materials with each density and mixing ratio, and bending performance was investigated. When the addition ratio of sawdust, rice husk and charcoal is 50:20:20 and the resin addition ratio is 10%, as the density of the prepared mixed board ranges from 0.5 g/cm³ to 0.7 g/cm³, the bending strength was 0.42~3.24 N/mm², dynamic modulus of elasticity was 94.5~888.4 N/mm², and the static modulus of elasticity was in the range of 31.4~220.7 N/mm². As the density increased, the bending performance increased, indicating that the density had a significant effect on the bending performance. In a board prepared by setting the density of 0.6 g/cm³, the addition ratio of sawdust to 50%, and the addition ratio of rice husk and charcoal at different ratios, the bending performance showed a tendency to decrease as the addition ratio of charcoal increased. The relationship between the addition ratio of rice husk and charcoal, bending strength, resonance frequency, and dynamic and static bending modulus showed a rather low correlation with the values of the coefficient of determination (R²) of 0.4562, 0.4310, 0.4589, and 0.5847, respectively. Thus, we found that the effect of the addition ratio on the bending performance was small.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.6
• /
• pp.33-39
• /
• 2012

With the increase of steel production research interest on the recycling of slag as a by-product also increases steadily. Currently in Korea a lot of researches on blast-furnace slag have been made. However, the researches on the steel slag have been rarely made. Also, a research of steel slag, especially the use of oxidation furnace slag as aggregates for concrete progress, is performing actively, but the research results on the furnace slag are almost nothing. Recently, the research about the furnace slag as backfill material and embankment material confirmed the possibility of the clay soil amendment. Therefore, the object of this study is to review the possibility as civil engineering materials for soil improvement and to find the optimum mixture ratio of furnace slag. This research analyzed the ingredient component of the reduced slag by SEM, XRF, XRD tests and examined the strength increase using unconfined compression tests when the clay and reduced slag are mixed each other. Through this test, the definite strength increase is confirmed according to the mixture of the reduced slag and the possibility of soil improvement is also confirmed based on this result. The object of the study is both utilizing the by-product for civil engineering purpose and effective recycling by the application of the furnace slag for soil improvement.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.2
• /
• pp.235-244
• /
• 2020

This study conducted a series of studies to offer a novel method of using CBS-dust that produced as by-product in the manufacture of cement. Four different contents of BS and CBS-dust were adopted for test parameters of this study. Mortar with 50% of W/B was fabricated. First, in the case of the fresh mortar, the flow decreased as the CBS-dust replacement rate increased, but the binder composition ratio BS 45% and 65% showed higher fl ow than Pl ain when repl acing CBS-dust 5%. In the case of air content, overall, the tendency was proportional to the CBS-dust replacement rate, and chloride tended to exceed the reference value at all replacement rates except for the CBS-dust 0% replacement. The compressive strength of the hardened mortar shows the resul t that the strength is improved when the CBS-dust is repl aced by 5% to 10%, and the CSH gel and structure formation is confirmed by microstructure analysis through the hydration reaction when the CBS-dust is replaced. Therefore, for a given condition CBS-dust is used as a early-strength admixture in a concrete secondary product that uses a large amount of admixture without reinforcing bars it can be an effective method for enhancing the strength of concrete as an alkali activator.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.204-210
• /
• 2022

Cement is pointed out as the main cause of carbon dioxide emission in the construction industry. Many researchs are underway to use blast furnace slag, an industrial by-product, as a substitute for cement to reduce carbon dioxide emitted during the manufacturing the cement. When blast furnace slag is used as a substitute for cement, it has advantages such as long-term strength and chemical resistance improvement. However, blast furnace slag has a problem that makes initial strength low. This is due to the impermeable film on the surface created during the production of blast furnace slag. The created film is known to be destroyed in an alkaline environment, and based on this, previous studies have suggested a solution using various alkali activators. But, alkali activator is dangerous product since it is a strong alkaline material. And it has the disadvantage in price competitiveness. In this study, an experiment was conducted to improve the initial hydration reactivity of the blast furnace slag to secure the initial strength of the mortar substituted with the blast furnace slag and to check whether the carbonation resistance was increased. As a result of the experiment, it was confirmed that the mortar using alkaline water showed higher strength than the mortar using tap water, and there were more hydration products generated inside. In addition, it was confirmed that the mortar using alkaline water as a compounding water had high carbonation resistance.

• Food Science of Animal Resources
• /
• v.37 no.5
• /
• pp.708-715
• /
• 2017

The acid pretreatment of collagen molecules disrupts their crosslinks and assists in the release of acid-soluble proteins, fats, and other components. Generally, to achieve optimum extraction efficiency, strong acids may be used at a lower acid concentration compared to weak acids. This study aimed to determine the yield and physicochemical properties of gelatins extracted from buffalo hides pretreated with different acids. Hides were extracted with hydrochloric, citric, and acetic acids at concentrations of 0.3, 0.6, 0.9, 1.2, and 1.5 M. A completely randomized design and the least significant difference test were used in the experimental design, and all measurements were performed in triplicate. The highest yield (29.17%) was obtained from pretreatment with 0.9 M HCl. The gel strength did not differ significantly (p>0.05) according to acid type (280.26-259.62 g Bloom), and the highest viscosity was obtained from the 0.6 M citric acid pretreatment. All the gelatins contained ${\alpha}$- and ${\beta}$-chain components and several degraded peptides (24-66 kDa). The color and Fourier-transform infrared spectrum of the gelatin extracted using 0.9 M HCl were similar to those of commercial bovine skin gelatin. In general, the physicochemical properties of the gelatin complied with the industry standard set by the Gelatin Manufacturers Institute of America, revealing that buffalo hide could serve as a potential alternative source of gelatin.