• Design & Manufacturing
• /
• v.18 no.3
• /
• pp.54-63
• /
• 2024

This study applied the insert molding technology which is a metal and resin joining method, to secondary battery prismatic cap assembly component and investigated the improvement comparing with standard PHEV2 Type of prismatic battery under the goal of enhancing the global market competitiveness by reducing the number of cap assembly sub-component and simplifying its manufacturing processes. Insert molding replaced the rivet terminal which is composed of 6 parts to which led significant decreasing of product cost, weight and resistance and increasing tensile strength. The angle of current collector to cap plate is a key of leakage defect which is determined by temperature of product and mold, injection temperature, pressure and time and these data can be used for bigger size of insert cap assembly as the demand of high capacity battery is getting high

• Journal of Life Science
• /
• v.13 no.4
• /
• pp.481-491
• /
• 2003

A squid meat has not been utilized for gel products because of its lower gel forming ability. The objectives of this study were as followed; 1) the optimum heating condition on squid meat paste products and 2) the optimum added level for jelly strength of squid meat paste products. Optimum heating conditions of squid meat kamaboko were as followed; setting (pre-heating) at 15$^{\circ}C$ or 55$^{\circ}C$ for 2 hours and heating at 90$^{\circ}C$ for 60 minutes. Effect for jelly strength of starch additives wheat starch, potato starch and com starch were examined. The jelly strength of heat induced gels differed from the levels of additives. In case of adding starch, potato starch was resulted in the superior jelly strength than the other starchs, wheat starch and corn starch, at any levels. Optimum concentration was 10%(w/w) at every additives. Folding test value was B at added 10% and this value was mean good product. Data of jumbo and flying squid meat paste products added potato starch, corn starch and wheat starch of 10% were shown below, jelly strengths were 858${\pm}$34∼1020${\pm}$37gㆍcm and 966${\pm}$33∼l148${\pm}$45gㆍcm and moisture contents were 72.43∼73.04% and 71.61∼72.78%, respectively. To adding edible agar and sea tangle, showed the highest jelly strength (edible agar>sea tangle, flying squid>jumbo squid) at added 0.5%(w/w) concentration.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.81-87
• /
• 2014

Conditions of paper manufacturing process should be changed depending on the end use and paper properties. Most of the case, mixed pulps with long softwood fibers and short hardwood fibers are used to achieve proper qualities of product with reasonable production cost. For specialty paper manufacture the wood pulp and cotton linter pulp are usually mixed together. The objectives of this study is to analyze physical, mechanical and fracture mechanical properties of paper depending on SwBKP, HwBKP and cotton linter pulp(CLP) mixing. When the mixing ratio of SwBKP was increased, strength properties, such as tensile, tear, and folding endurance, were also increased. When the mixing ratio of SwBKP and HwBKP was increased, stress concentration index was decreased and fracture toughness was increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.169-175
• /
• 1994

This study attempts to develop a process which can produce three-dimensional shapes of metals directly from CAD data. Prototypes made from metals, can not only be used to test the mecchanical properties of the product, but also potentially become the actual die or product itself. The test-device of the process has been designed and manufactured. The laser scanning method using a scanning path schedule composed of circle and arc elements, scanning speed variation method and dwell method have been developed, which resist warping phenomenon and increase the adhesiveness between the layers. For the production of prototypes with pure iron powder, the optimal values of the principal process parameters have been determined, through which cross-shaped and twisted clover-shaped prototypes have been fabricated. In order to improve the strength of the prototype, the experimental studies of solid-phase sintering, and copper infiltration have been done.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.164-169
• /
• 2018

In this study, we solved the human hazard problem of aluminum liner by applying plastic PET liner which is widely used as a material for food and beverage containers in the market. In order to reinforce dome area by using low strength / high elongation plastic liner, The aluminum boss was covered on the plastic liner surface. In order to predict the performance of the developed product, the structural analysis was carried out by applying the three - dimensional laminated solid element, and the soundness of the product was verified through the prototype performance test.

• Resources Recycling
• /
• v.33 no.1
• /
• pp.48-57
• /
• 2024

This study aimed to improve utilization of the Class C vinyl waste generated in rural areas based on a preliminary investigation on the use of eco-powder, generated through pyrolysis, as a raw material for plastic. The efficiency of pre-processing treatments in controlling ash content of the generated eco-powder and its effect on the basic properties of manufactured plastic were evaluated. The basic properties included ash content of the compressed eco-powder at different levels of ash content, impact strength, flexural strength, and tensile strength. The experimental results confirmed that pre-processing improved the separation efficiency of soil particles and vinyl waste through physical impact. The eco-powder with ash content of less than or equal to 26% was found to satisfy the target performance during impact strength, flexural strength, and tensile strength evaluation. Thus, it was confirmed that the Class C vinyl waste, having low utilization and recovery rates, could be effectively utilized as a plastic raw material after optimum thermal treatment and physical processing using the eco-powder.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.511-516
• /
• 2002

Pitch is a perception related to the subjective frequency that is one of the psychological aspects or attributes of tones. It is also an important factor to determine the sound quality together with loudness and timber. Although the study on pitch has been active in the field of speech communication, but its application to the product sound quality is not yet enough. In this study, the empirical data by Zwicker is made use in the modification of the currently available pitch extraction model based on the place theory. By applying this modified model to various sound samples composed of tonal or banded components, the applicability of the model is suggested. As a demonstration example, the algorithm is used for the sound quality analysis of a product noise having fundamental frequency and harmonics. The result shows that the pitch should be regarded as an important subjective cue in the sound quality analysis.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.221-227
• /
• 2003

Heat treatment is widely used in various manufacturing Processes to enhance the quality of a Product such as strength, surface hardness, and service life. In the heat treatment, there is dimensional change or distortion of the product, which critically influences the dimensional accuracy of precision parts. In this study, the distortion of a straight bevel gear induced by heat treatment is investigated in two cases. In the first case, the distortion induced by heat treatment we compared between a forged bevel gear and a machined bevel gear. In the second case, the distortion of an annealed gen is compared with that of a quenched gear. And finite element analysis has been Performed to predict the distortion of a heat-treated and machined bevel gear. The predicted values are compared with the experimental values.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.11-14
• /
• 2004

The object of this study is vibrating compaction and curing method in the production process of Design concrete for precast concrete(Design-PC) product. From change of vibrating compaction time and pre-curing time. curing temperature which would be factors of product quality in Design-PC concrete production. and research of optimized steam curing condition from relations between curing condition and strength development. basic data of vibrating compaction time and concrete steam curing method for Design-PC will be presented.

• Proceedings of the Safety Management and Science Conference
• /
• 2004.05a
• /
• pp.303-307
• /
• 2004

Is not used by consistency transport at transport of freight nothing but is using Pallet only by pedestal when work palletized unit load or materials handling when keep simplicity receptacle which fill raw material or product in factory in our country. Therefore, pallet that is most important function of Pallet is not empled circulation to end consumer from manufacturing plant which is circulation process whole path being done and factory. It is real condition stopping only in extremely determinate part process use of warehouse back. Additionally, it is possible to figure out the flow of all the materials loaded on the RFID pallet; product, material, raw material immediately, so that epoch-making management is possible and it contributes to the reduction of logistics cost because there are little loss or outflow of pallet. The materials flow is getting speedy and inventory is decreasing in the logistics process, and also bad inventory and loss problems are prevented. As a result, not only logistics cost of company but also national logistics cost is decreased. Thus it contributes to the strength of national competitiveness.