• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권4호
• /
• pp.143-148
• /
• 2002

Up to now, DC-biased magnetic properties have been measured in one dimension (scalar). However, scalar magnetic properties are insufficient to clarify DC-biased magnetic properties because scalar magnetic properties can only impossibly consider the phase difference between the magnetic flux density B vector and the magnetic field strength H vector. Thus the magnetic field strength H and magnetic flux density B in magnetic materials must be directly measured as a vector quantity (two-dimensional). This paper presents measurement system to clarify the two-dimensional DC-biased magnetic properties.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.395-396
• /
• 2006

To manufacture a flange for a compressor with a relief groove by using powder metallurgy in order to prevent deformation to the compressor in operation, powder material for the flange is charged into a mold; an ablative member having a melting point lower than that of the powder material is positioned at a place where a relief groove is to be formed; the flange is formed by compressing the powder material and the ablative member; and the formed flange is sintered at a temperature between the melting point of the powder material and the ablative member so as to melt and remove the ablative member. It made according to the new method has more excellent strength and airtight property than the conventional one. It is analyzed that the ablative member is melted and penetrated into the flange structure during the sintering process, which results in improvement of the airtight property and increase of the strength.

• 열처리공학회지
• /
• 제21권4호
• /
• pp.205-212
• /
• 2008

Characteristics of microstructures, mechanical properties and formability of two Al-20Si-5Fe-2Ni alloys produced by gas atomizing (P/M) and spray forming (S/F) respectively were compared at temperatures up to $560^{\circ}C$. Room temperature hardness values and tensile strengths of both alloys were increased in accordance with temperature after heat treatment above $300^{\circ}C$. The highest values of hardness and tensile strength of both alloys were obtained at $490^{\circ}C$. It was interpreted that increase in hardness and tensile strength according to heating temperature between $300{\sim}490^{\circ}C$ was mainly related to increase in internal stress between Al matrix and reprecipitated particles. S/F alloys showed better formability and wear property than P/M alloys due to the homogenity of microstructures above $300^{\circ}C$.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.59-63
• /
• 2016

A key point of a soldering process for photovoltaic (PV) modules is to increase an adhesive strength leading a low resistivity between ribbon and cell. In this study, we intended to optimize a heating condition for the soldering process and characterize the soldered joint via physical and chemical analysis methods. For the purpose, the heating conditions were adjusted by IR lamp power, heating time and hot plate temperature for preheating a cell. Since then the peel test for the ribbon and cell was conducted, consequently the peel strength data shows that there is some optimum soldering condition. In here, we observed that the peel strength was modified by increasing the heating condition. Such a soldering property is affected by a various factors of which the soldered joint, flux and bus bar of the cell are changed on the heating condition. Therefore, we tried to reveal causes determining the soldering property through analyzing the soldered interface.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2010년도 춘계 학술논문 발표대회 1부
• /
• pp.77-81
• /
• 2010

This study deals with the analysis of color-difference and physical property of anti-corrosion coatings using at inside of concrete tank for drinking water. Because anti-corrosion coatings are effected by chemical attack, color and physical property are changed. So in this study when epoxy resin coatings of 3 types were received chemical attack by Cl- and NaOH, we present the co-relationship between color-difference and bond strength. For this study, we used the colorimetry, which can measure the degree of color difference on surface of materials. As the results, in case of Cl-, color change is appeared, bond strength also is decreased. From this experiment, we could know that color change due to chemical aging has the deep relationship with physical performance(bond strength) materials. further researches are needed.

• Steel and Composite Structures
• /
• 제22권1호
• /
• pp.45-61
• /
• 2016

The domestic and foreign scholars conducted many studies on mechanical properties of wave web steel beam and high-strength spiral stirrups confined concrete columns. Based on the previous research work, studies were conducted on the anti-seismic property of the end plate bolt connected wave web steel beam and high-strength spiral stirrups confined concrete column nodes applied with pre-tightening force. Four full-size node test models in two groups were designed for low-cycle repeated loading quasi-static test. Through observation of the stress, distortion, failure process and failure mode of node models, analysis was made on its load-carrying capacity, deformation performance and energy dissipation capacity, and the reliability of the new node was verified. The results showed that: under action of the beam-end stiffener, the plastic hinges on the end of wave web steel beam are displaced outward and played its role of energy dissipation capacity. The study results provided reliable theoretical basis for the engineering application of the new types of nodes.

• 한국주조공학회지
• /
• 제32권1호
• /
• pp.38-43
• /
• 2012

The effects of Mg and Cu amounts on the casting characteristics and tensile property of Al-Zn-Mg-Cu alloys were investigated for the development of high strength aluminium alloys for gravity mold casting. Increase of copper amounts in Al-6%Zn-3%Mgy% Cu alloys resulted in reduction of the fluidity of these alloys and had little effects on the tensile property of these alloys. Increase of magnesium amounts from 1.0wt% to 3.3wt% in Al-6%Zn-x%Mg-0.5%Cu alloys resulted in reduction of the elongation of these alloys from 12% to 3% and increase of the tensile strength of these alloys from 340MPa to 450MPa, but had little effects on the fluidity of these alloys.

• 한국의류학회지
• /
• 제25권7호
• /
• pp.1193-1202
• /
• 2001

The goal of this research is to investigate the effect of fusible interlinings on the mechanical characteristics and appearance related values for the Lyocell fabrics. In this study, to establish optimum fusing conditions, peel strength of the fused fabrics depending on the fusing temperature, pressure and time was measured. Appearance related properties and mechanical characteristics of the fused fabrics ere determined. The reulst are as follows: In the fusing condition of $120^{\circ}C,\;3kgf/textrm{cm}^2$, 15sec, peel strength was excellent. Peel strength was excellent in the case of tencel/cotton fabric, with increasing cover factor of woven interlining, with twill and nonwoven interlining. Flex stiffness was increased in the case of tencel/cotton fabric, with increasing weight of woven interlining, with twill and nonwoven interlining. Drapability was excellent in the case of 100% tencel fabric, with decreasing weight of woven interlining, with plain and woven interlining. Crease recovery was excellent in the case of 100% tencel fabric, with increasing weight of woven interlining, with twill and woven interlining. Shear and bend properties were increased in the case of tencel/cotton fabric, with increasing weight of woven interlining, with plain and nonwoven interlining.

• Geomechanics and Engineering
• /
• 제11권1호
• /
• pp.161-175
• /
• 2016

A series of experimental studies are conducted on the deformation and shear strength property of compacted loess. The results reveal that the relationships of both the initial moisture content (w) and the initial degree of compaction (K) of compacted loess with cohesion (w) and the angle of internal friction (${\varphi}$) are linear. The relationship between the secant modulus ($E_{soi}$) and K is also linear. The relationship between $E_{soi}$ and w can be fitted well by a second-order polynomial. Further, when the influences of w and K are ignored, the relationship between the confined compression strain (${\varepsilon}$) and vertical pressure (p) can be expressed by a formula. A correction formula for the deformation of compacted loess caused by a change in w and K is derived on the basis of the study results.

• 패션비즈니스
• /
• 제16권1호
• /
• pp.52-68
• /
• 2012

To achieve the aim of this study, 9 different types of samples were made to examine mechanical property according to structured pattern and type of Machi of pullover armhole of WholeGarment(seamless knitwear). With respect to samples, from which comparisons are made and anaylzed among basic characteristics of material, tensile strength & elongation and residual elongation due to repeated extension of armhole connecting part, the following conclusions could be obtained. It's revealed that the tensile strength of Machi part as being armhole connecting part of samples is more affected by Machi type than pattern structure. Of Machi types, it showed stronger tensile strength in the order of Normal(Normal Machi)< Machi_B(unilateral Machi)