• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.1
• /
• pp.13-20
• /
• 2005

The effects of pectin on obesity was studied using 3T3-L1 pre-adipocytes and rats fed 20% high fat diets. The concentration of leptin released from 3T3-L1 adipocytes in the presence of pectin was significantly decreased by 85% compared to that of the control (p<0.05), however, glycerol concentration was not changed. These data indicate that pectin seems to inhibit lipids accumulation in the adipocytes rather than enhance the lipolytic activity. Forty Sprague Dawley rats were fed 20% high fat diet for 8 weeks to induce obesity and then divided equally into four groups. Experimental groups were normal diet group (ND), high fat diet group (HFD), HDF with 10% pectin group (HFP10), and HDF with 20% pectin group (HFP20). Diet for the each group was prepared to be iso-caloric following AIN-76 guideline. After obesity was induced, rats were placed on an restricted diet for 9 weeks. The body weight of HFD increased 50% (p<0.05) compared to the ND, while it was decreased by 12% and 16% for HFP10 and HFP20, respectively (p<0.05). The relative amount of visceral fats for HFDl0 and HFD20 were decreased by 45% and 59% compared to that of HDF (130%), respectively (p<0.05). Pectin seems to have a greater effect on reducing visceral fats accumulation than weight reduction. Significantly increased level of triglyceride, total cholesterol or LDL-cholesterol in the plasma of HFD was returned to the normal or even below the normal by pectin diet, while the level of HDL-cholesterol increased. Lipid lowering effect was also observed in the liver and heart. These effects of pectin were dosedependent. In conclusion, the beneficial effect of pectin on the obesity was observed from cell culture experiment and animal study in terms of inhibiting the accumulation of lipids in the adipocytes.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.145-155
• /
• 2002

The results of the present feasibility study are summarized as follows, 1. The three unit bridge of knitted material and UD fibre reinforcement has both the rigidity and the strength against a vertical occlusal load of 75N. 2. Stress concentration at the junctional area between the bridge and the abutments, i.e. between the pontic and the knitted caps was observed. In the case of the bridge with reinforcement straps, it was partly shown that the concentration problem could be improved by simply increasing the fillet size at the area. Further refining in the surface of the junctional area will be needed to ensure a further improvement in the stress distribution. This will require some trade off in the level of the stress and the available space. A parametric study will help to decide the appropriate size of the fillet. 3. Design refinement is a must to improve the stress distribution and realize the most favourable shape in terms of fabrication. The current straight bar with a constant cross section area can be redesigned to a tapered shape. The curve from the dental arch should also be placed on the pontic design. In accordance with design refinement, the resistance of the bridge frame to other load cases should be evaluated. 4. Although not included in the present feasibility study, it is estimated that bridges of the anterior teeth can be made strong enough with the knitted material without further reinforcement using unidirectional materials. In this regard, a feasibility study on design concepts and stress analysis for 3, 4, 5 unit bridge is suggested. 5. Two types of bridge were analysed in terms of fatigue. The safe life design concept, i.e. fatigue design concept, looks reasonable for the bridge where if cracks should form and propagate there is virtually nothing a dentist to do. The bridge must be designed so that no crack will be initiated during the life span. In the case of crowns, however, if constructed with composite resin with knitted materials, it might be possible to repair them, which in general is impossible for crowns of PFM or of metal. Therefore for composite resin crowns, a damage tolerance design concept can be applied and reasonably higher operational stresses can be allowed. In this case, of course, a periodic inspection program should be established in parallel. 6. Parts of future works in terms of structural viewpoint which need to be addressed are summarized as the following: 1) To develop processing technology to accommodate design concepts; 2) More realistic modelling of the bridge and analysis-geometry and loading condition. Thickness variation in the knitted material, taper in the pontic, design for anterior tooth bridge, the effect of combined loads, etc, will need to be included; 3) To develop appropriate design concepts and design goals for the fibre composite FPD aiming at taking the best advantage of knitted materials, including the damage tolerance design concept; 4) To develop testing method and perform test such as static ultimate load test, fatigue test, repair test, etc, as necessary.

• Horticultural Science & Technology
• /
• v.29 no.5
• /
• pp.447-455
• /
• 2011

To investigate the effects of the improvement of postharvest quality on fresh tomato, antimicrobial microperforated (AMP) films were prepared and their antimicrobial abilities were observed. AMP films were made by coating different types of natural antimicrobial agents such as cinnamon, clove, and clary sage essential oils into microperforated (MP) films. Cinnamon essential oil of 10% (v/v) has proven to be very effective as inhibitor of the mold growth on tomato, compared to the clove and clary sage essential oils. Quality changes of fresh tomatoes packed using the natural AMP films (AMP10 and AMP30) and MP films (MP10 and MP30) during storage were evaluated. Total microbial growth, weight loss, firmness, lycopene content, and decay rate as the major quality parameters were monitored over 9 days at $15^{\circ}C$. The oxygen transmission rates and mechanical properties between the natural AMP and MP films were also compared. There was no significant difference in change of oxygen transmission rate, tensile strength and elongation between the AMP and MP films. For storage studies, the freshness of tomato packaged in AMP30 film was higher than that in OPP film (the control), MP10, MP30, and AMP10 films. Especially, AMP30 film exhibited high efficiency compared to the control for tomato decay during storage periods. Based on the results, the microperforation and antimicrobial properties of the packaged films may significantly affect the maintenance of an optimum gas composition within the package atmosphere for increasing the storage life and quality of produce. They were also effective on the inhibition of microbial growth by controlled release of antimicrobial agent at an appropriate rate from the package into the tomato. Natural antimicrobial agent coating microperforated films could use potential functional package as a method of extending the freshness of postharvest tomato for storage.

• Geotechnical Engineering
• /
• v.12 no.4
• /
• pp.157-178
• /
• 1996

Current design methods for reinforced earth structures take no account of the magnitude of the strains induced in the tensile members as these are invariably manufactured from high modulus materials, such as steel, where straits are unlikely to be significant. With fabrics, however, large strains may frequently be induced and it is important to determine these to enable the stability of the structure to be assessed. In the present paper internal design method of analysis relating to the use of fabric reinforcements in reinforced earth structures for both stress and strain considerations is presented. For the internal stability analysis against rupture and pullout of the fabric reinforcements, a strain compatibility analysis procedure that considers the effects of reinforcement stiffness, relative movement between the soil and reinforcements, and compaction-induced stresses as studied by Ehrlich 8l Mitchell is used. I Bowever, the soil-reinforcement interaction is modeled by relating nonlinear elastic soil behavior to nonlinear response of the reinforcement. The soil constitutive model used is a modified vertsion of the hyperbolic soil model and compaction stress model proposed by Duncan et at., and iterative step-loading approach is used to take nonlinear soil behavior into consideration. The effects of seepage pressures are also dealt with in the proposed method of analy For purposes of assessing the strain behavior oi the fabric reinforcements, nonlinear model of hyperbolic form describing the load-extension relation of fabrics is employed. A procedure for specifying the strength characteristics of paraweb polyester fibre multicord, needle punched non-woven geotHxtile and knitted polyester geogrid is also described which may provide a more convenient procedure for incorporating the fablic properties into the prediction of fabric deformations. An attempt to define improvement in bond-linkage at the interconnecting nodes of the fabric reinforced earth stracture due to the confining stress is further made. The proposed method of analysis has been applied to estimate the maximum tensions, deformations and strains of the fabric reinforcements. The results are then compared with those of finite element analysis and experimental tests, and show in general good agreements indicating the effectiveness of the proposed method of analysis. Analytical parametric studies are also carried out to investigate the effects of relative soil-fabric reinforcement stiffness, locked-in stresses, compaction load and seepage pressures on the magnitude and variation of the fabric deformations.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.89-97
• /
• 2005

Recently, for the problem solution of demand and supply imbalance of fine aggregate due to the shortage of natural fine aggregate resource and the environment regulation on sea sand extraction in the construction field, the studies for the application of recycled fine aggregate using waste concrete are being progressed versatilely. On the other hand, the treatment of fly-ashes that of industrial by-product originated in the steam power plant is discussed by the continuous increasing of origination quantities. In the ease of using fly-ash, advantages are the improvement of workability, viscosity and long-time strength, and the reduction of hydration heat under the early ages, as the admixtures for concrete, but the studies for the application of fly-ash as recycled concrete admixtures are inadequacy. There fore, in this study, through investigating the properties of fresh, hardened and durability according to the replacement of recycled fine aggregate and fly-ash, it is intended to propose the fundamental data for structural application of recycled concrete using recycled fine aggregate and fly-ash. As the result of this study, they arc shown that the engineering properties and durability, in the case of replacement ratio 100% of recycled fine aggregate, arc similar to those of concrete using natural fine aggregate, so it is considered that recycled fine aggregate could be used as the fine aggregate for concrete. Also, the performances of recycled concrete are improved by replacing fly-ash.

• Journal of the Korean Society of Radiology
• /
• v.6 no.2
• /
• pp.143-149
• /
• 2012

Today each hospital is trend that change rapidly by up to date, digitization and introducing newest medical treatment equipment. So, we introduce new CR system and supplement film system's shortcoming and PACS, EMR, RTP system's network that is using in hospital harmoniously and accomplish quality improvement of medical treatment and service elevation about business efficiency enlargement and patient Accordingly, we wish to introduce our case that integrate reflex that happen with radiation oncology here upon to PACS using CR system and estimate the availability. We measured that is Gantry, Collimator Star Shot, Light vs. Radiation, HDR QA(Dwell position accuracy) with Medical LINAC(MEVATRON-MX) Then, PACS was implemented on the digital images on the monitor that can be confirmed through the QA. Also, for cooperation with OCS system that is using from present source and impose code that need in treatment in each treatment, did so that Order that connect to network, input to CR may appear, did so that can solve support data mistake (active Pinacle's case supports DICOM3 file from present source but PACS does not support DICOM3 files.) of Pinacle and PACS that is Planning System and look at Planning premier in PACS. All image and data constructed integration to PACS as can refer and conduct premier in Hospital anywhere using CR system. Use Dosimetry IP in Filmless environment and QA's trial such as Light/Radition field size correspondence, gantry rotation axis' accuracy, collimator rotation axis' accuracy, brachy therapy's Dwell position check is available. Business efficiency by decrease and so on of unnecessary human strength consumption was augmented accordingly with session shortening as that integrate premier that is neted with radiation oncology using CR system to PACS. and for the future patient information security is essential.

• Journal of the Korean Arthroscopy Society
• /
• v.12 no.3
• /
• pp.198-204
• /
• 2008

Purpose: The purpose of this study is to analyze the merits and demerits of double bundle reconstruction and achieve improvements hereafter, by comparing the results of double bundle and single bundle reconstruction using tibialis anterior allograft. Materials and Methods: Twenty seven patients were divided to undergo either double bundle(n=14) or single bundle(n=13) reconstruction with tibialis anterior allograft tendon. The evaluation methods were AP laxity with KT-2000 arthrometer, isokinetic knee strength measurements, pivot-shift test, IKDC subjective score, Lysholm knee score, Tegner activity score, radiographic evaluations with postoperative MRI, and second look arthroscopy. Results: Lysholm knee score and Tegner activity score were significantly better in double bundle reconstruction. In pivot-shift test, single bundle reconstruction was evaluated as grade 0 in 10 of the knees, grade 1 in 1, and grade 2 in 2. Double bundle reconstruction was evaluated as grade 0 in 13, and grade 2 in 1. In second look arthroscopy, single bundle was evaluated as excellent in 6 of the knees, fair in 7, anteromedial bundle of double bundle reconstruction was excellent in 13 and fair in 1, and posterolateral bundle was excellent in 4, fair in 9, and poor in 1. There were no significant differences in other evaluations. Conclusion: Favorable outcome may be expected with double bundle reconstruction of ACL. However there are still need for improvement in terms of reconstruction technique and rehabilitation protocol to reduce PL bundle injury.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.9
• /
• pp.1434-1442
• /
• 2005

The Present study was attempted to investigate the Possibility of modification of functional properties of the rice flour by crosslinking proteins using microbial transglutaminase (mTGase) derived from a variant of Streptoverticillium sp. MTGase was added at various levels (3,000, 5,000, 7,000 and 10,000 ppm) during making noodles mixed with the rice flour. Mixograph and farinograph showed that imported wheat flour (IWF) had strong dough stability, while the rice flour showed very weak dough strength. However addition of mTGase (3,000, 5,000 and 7,000 ppm) resulted in improvement of dough stability of the rice flour. Texture profile analysis (TPA) results indicated that most of texture parameters (gumminess, chewiness and hardness) of cooked noodles prepared from the rice flour were significantly lower than those of noodles prepared from IWF. However, by addition of mTGase (at the levels of 3,000, 5,000, 7,000 ppm) dough stability and all the TPA values and sensory score (at the level of 7,000 ppm mTGase) on chewiness and hardness of cooked noodles made with $30\%$ rice flour were improved significantly. These results suggest that dough stability and texture of rice noodles as well as sensory characteristics could be improved by addition of mTGase to the rice flour.

• Journal of Animal Science and Technology
• /
• v.47 no.4
• /
• pp.547-554
• /
• 2005

An experiment was conducted to investigate the dietary effects of a transgenic Aspergillus oryzae(AO) culture on the performance, egg quality and intestinal microflora of layers. A total of 840 Hy-line Brown layers of 39wks old were assigned to one of the following 7 dietary treatments: control(C), C+0.2% AO culture, C+0.5% AO culture, C+0.2% transgenic AO culture, C+0.5% transgenic AO culture, C+0.2% transgenic mutant AO culture, and C+0.5% transgenic mutant AO culture. The transgenic AO was made by inserting Salmonella gallinarum gene to AO. And the transgenic mutant AO was made by inserting Salmonella gallinarum gene to mutant AO which was mutated by UV irradiation. Each treatment was replicated six times with 20 birds housed in 2 bird cage. Twenty birds units were arranged according to completely randomized block design. Feeding trial lasted for 8wks under 16 hour lighting regimen. Laying performance and egg quality were significantly(P<0.05) affected by the treatments. Transgenic AO culture supplementation at the level of 0.2% significantly increased egg production, while its egg weight was significantly decreased compared to that of the control. Feed intake and feed conversion ratio(FCR) were not significantly different among the AO treatments and the control. The eggshell strength of the AO treatments was significantly higher than that of the control. Transgenic mutant AO culture supplemented at the level of 0.5% significantly increased egg yolk color. Intestinal microflora were significantly(P<0.05) affected by the treatments. The cfu of Lactobacilli spp. significantly increased and those of Salmonella species and E. coli decreased in the AO treatments. The transgenic AO and transgenic mutant AO culture were more effective than the AO culture in reducing the cfu of Salmonella species and E. coli. It is concluded that supplementation of the transgenic AO culture at the level of 0.2% could be recommended for the improvement of egg production. Supplementation of transgenic AO or transgenic mutant AO culture at 0.2% level effectively controlled intestinal Salmonella species population.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.12 no.1
• /
• pp.91-98
• /
• 2008

Purpose: Radio-isotopes (RI) use has been steadily developing due to industrial and technical development in the modern medical society. Particularly, popularization of domestic cyclotrons dramatically enable hospitals to produce and use diagnostic radio-isotopes. Generally, only specific facilities such as hospitals, research institutes, nuclear power plants and universities can use radio-isotopes, they are also responsible for ventilation system. The strength of radioactivity in the air is strongly regulated and controlled by korea atomic energy law in Korea Institue of Nuclear Safety (KINS), so that air radioactivity exposure can lead to environmental pollution surrounding places. In this study, we'd like to find out the investigation and the present condition of the controlled ventilation system in domestic hospitals by an emission standard from KINS, and try to reach an agreement about how to use the ventilation system. Result: Definition of filters, features and structures of pre-filters, hepa-filters, charcol filters, filter exchange procedures and precautions are explained. RI deflation concentration and filter exchange cycle have been presented as a standard prescribed in the rules of KINS. The Radiation Control Management System (RCMS) introduced by Seoul National University Bundang Hospital linking to digital pressure gauge with computer controller in another medical facilities were described in details. Conclusions: The system of medical facilities using RI has been remarkably developing in 21 century. Especially, radiation safety control system has also been grown rapidly into the subdivision, specialization, advanced technology along with international technical improvement. However, As far as current RI ventilation system is concerned, it has nothing better than doing in the past. Preferentially, to reinforce this, more sophisticated system with strict periodic filter exchange and exhaust air control guidance should be introduced by applying brilliant domestic information technology for RCMS and digital gauge method. From personal point of view as a radiation safety manager, I have provide with present problems and improvements. Futhermore, more improved guidance should be conducted.