• 한국전산구조공학회논문집
• /
• 제26권4호
• /
• pp.263-269
• /
• 2013

본 논문에서는 건물의 횡방향 구조반응을 평가하기 위한 변형률 기반의 모니터링 기법이 제시되고, 이에 대한 기초 연구로써, 구조해석을 통해 제안된 기법을 검증한다. 광섬유 격자 센서(fiber Bragg grating, FBG)는 일반 변형률 센서와 비교하여 내구성이 뛰어날 뿐 아니라 높은 샘플링 수와 여러 지점을 동시에 계측할 수 있는 장점이 있다. 이러한 특성 때문에 FBG 센서는 구조 모니터링을 위해 많은 센서가 요구되는 건물의 모니터링에 적합하다. 본 연구에서 FBG 센서는 수직 부재의 변형률을 계측하며, 이는 해당 부재의 곡률을 평가한다. 이러한 곡률은 횡변위와 횡가속도를 평가하는데 사용된다. 추가적으로 횡방향 가속도는 frequency domain decomposition(FDD) 기법을 이용하여 구조물의 고유진동수와 모드형상을 추정하는데 사용된다. 9층 철골모멘트 골조 예제의 적용을 통해, 제시된 기법이 건물의 다양한 횡방향 구조 반응과 동적 특성을 평가하는데 적절함을 확인하였다.

• Geomechanics and Engineering
• /
• 제24권1호
• /
• pp.67-79
• /
• 2021

The influence of ground motions on the seismic response of utility tunnels was investigated. A series of small-scale shaking table model tests were carried out under uniform excitation in the transverse direction. Different peak accelerations of EL-Centro and Taft earthquake waves were applied. The acceleration responses, earth pressure, seismic strain, bending moment and structure deformations were measured and discussed. The results showed that the types of earthquake waves had significant influences on the soil-structure acceleration responses. However, the amplitude of the soil acceleration along the depth showed consistent variation regardless of the types of earthquake waves and tunnels. The horizontal soil pressure near the top and bottom slabs showed obviously larger values than those at other depths. In general, the strain response in the outer surface was more significant than that on the inner surface, and the peak strain in the end section of the model was larger than that in the middle section. Moreover, the bending moment at the corner points was much larger than that at middle point, and the bending moment was greatly affected by both input accelerations and seismic wave types. The opposite direction of shear deformation on the top and bottom slabs presented a rotation trend of the model structure.

• Earthquakes and Structures
• /
• 제10권5호
• /
• pp.1089-1109
• /
• 2016

Modified two-surface model (M2SM) is one of the steel elasto-plastic hysteretic constitutive models that consider both analysis accuracy and efficiency. However, when M2SM is used for complex strain history, sometimes the results are irrational due to the limitation of stress-strain path judgment. In this paper, the defect of M2SM was re-modified by improving the judgment of stress-strain paths. The accuracy and applicability of the improved method were verified on both material and structural level. Based on this improvement, the nonlinear time-history analysis was carried out for a deck-through steel arch bridge with a 200 m-long span under the ground motions of Chi-Chi earthquake and Niigata earthquake. In the analysis, we compared the results obtained by hysteretic constitutive models of improved two-surface model (I2SM) presented in this paper, M2SM and the bilinear kinematic hardening model (BKHM). Results show that, although the analysis precision of displacement response of different steel hysteretic models differs little from each other, the stress-strain responses of the structure are affected by steel hysteretic models apparently. The difference between the stress-strain responses obtained by I2SM and M2SM cannot be neglected. In significantly damaged areas, BKHM gives smaller stress result and obviously different strain response compared with I2SM and M2SM, and tends to overestimate the effect of hysteretic energy dissipation. Moreover, at some position with severe damage, BKHM may underestimate the size of seismic damaged areas. Different steel hysteretic models also have influences on structural damage evaluation results based on deformation behavior and low cycle fatigue, and may lead to completely different judgment of failure, especially in severely damaged areas.

• 한국미생물·생명공학회지
• /
• 제47권1호
• /
• pp.87-95
• /
• 2019

Esterase produced by Acinetobacter sp. B1 (strain B1) was optimized by means of one-variable-at-a-time and response surface methodologies. Results of the one-variable-at-a-time experiment showed that Tween 80 significantly increased esterase production of strain B1. The addition of Tween 80 to the culture medium increased the biomass and esterase activity of strain B1, stimulated content of total extracellular protein, and enhanced the oleic acid (C18:1) composition in the cell membrane of strain B1. The influence of eight culture variables on esterase production was evaluated by Plackett-Burman design. Results showed that Tween 80, pH, and $K_2HPO_4$ significantly affected the esterase production of strain B1. Tween 80, pH, and $K_2HPO_4$ were further optimized by central composite design. Under the optimized conditions (w/v, soluble starch 2.5%, tryptone 1.5%, Tween 80 0.8%, $K_2HPO_4$ 0.5%, NaCl 0.5%, pH 8.0, inoculum size 1%, and inoculum age 24 h), the maximum esterase activity of strain B1 was 152.13 U/ml, which was 10-fold higher than that of non-optimization after 36 h cultivation.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.793-801
• /
• 1990

A single mode fiber-optic Mach-Zehnder interferometer for the measurement of strain is described. A fiber-optic strain gauge with great resolution and wide measurement range is realized. In order to varify the dynamic response, the measurements of strain below 1涅 with frequency range 5-50Hz are compared with a semiconductor strain gauge. We report theoretical evaluation for mechanical analysis, PZT-plate, the phase change in a fiber-optic strain gauge and a semiconductor strain gauge. The dynamical characteristics of a fiber-optic strain gauge and a semiconductor strain gauge output siganl show equivalent behavior. This result is shown in very good usage as the dynamical measurement of the low strain below 1涅 by this system.

• Geomechanics and Engineering
• /
• 제15권3호
• /
• pp.919-925
• /
• 2018

Stress-strain responses of weak-to-strong carbonate rocks used for tunnel construction were studied. The analysis of applicability of exponential stress-strain models based on Haldane's distribution function is presented. It is revealed that these exponential equations presented in transformed forms allow us to predict stress-strain relationships over the whole pre-failure strain range without mechanical testing of rock samples under compression using a press machine and to avoid measurements of axial failure strains for which relatively large values of compressive stress are required. In this study, only one point measurement (small strain at small stress) using indentation test and uniaxial compressive strength determined by a standard Schmidt hammer are considered as input parameters to predict stress-strain response from zero strain/zero stress up to failure. Observations show good predictive capabilities of transformed stress-stress models for weak-to-strong (${\sigma}_c$ <100 MPa) heterogeneous carbonate rocks exhibiting small (< 0.5 %), intermediate (< 1 %) and large (> 1 %) axial strains.

• 한국농공학회논문집
• /
• 제53권3호
• /
• pp.19-26
• /
• 2011

In order to estimate the viscous effects of clay over a wide range of strain levels, we confirmed the performance of a viscoelastic-viscoplastic constitutive model by simulating cyclic undrained triaxial tests to determine the cyclic strength and deformation characteristics of natural marine clay. The viscoelastic-viscoplastic constitutive model was then incorporated into an effective stress-based seismic response analysis to estimate the effects of an intermediate clay layer on the behavior of sand layers. Seismic response was simulated by the cyclic viscoelastic-viscoplastic constitutive model created with data recorded at Rokko Island, Kobe, Japan. The results show that a cyclic viscoelastic-viscoplastic constitutive model can provide a good description of dynamic behavior including viscoelastic effects, within a small strain range.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.1334-1339
• /
• 2006

Dynamic response of buried pipelines both in the axial and the transverse directions on concrete pipe and steel pipe, FRP pipe were investigated through a forced vibration analysis. The dynamic behavior of the buried pipelines for the forced vibration is found to exhibit two different forms, a transient response and a steady state response, depending on the time before and after the transfer of a seismic wave on the end of the buried pipeline. The former is identified by a slight change in its behavior before the sinusoidal-shaped seismic wave travels along the whole length of the pipeline whereas the latter by the complete form of a sinusoidal wave when the wave travels throughout the pipeline. The transient response becomes insignificant as the wave speed increases. From the results of the dynamic responses at the many points of the pipeline, we have found that the responses appeared to be dependent critically on the boundary end conditions. Such effects are found to be most prominent especially for the maximum values of the displacement and the strain and its position.

• Earthquakes and Structures
• /
• 제13권3호
• /
• pp.241-253
• /
• 2017

In this paper, dynamic response of the horizontal nanofiber reinforced polymer (NFRP) strengthened concrete beam subjected to seismic ground excitation is investigated. The concrete beam is modeled using hyperbolic shear deformation beam theory (HSDBT) and the mathematical formulation is applied to determine the governing equations of the structure. Distribution type and agglomeration effects of carbon nanofibers are considered by Mori-Tanaka model. Using the nonlinear strain-displacement relations, stress-strain relations and Hamilton's principle (virtual work method), the governing equations are derived. To obtain the dynamic response of the structure, harmonic differential quadrature method (HDQM) along with Newmark method is applied. The aim of this study is to investigate the effect of NFRP layer, geometrical parameters of beam, volume fraction and agglomeration of nanofibers and boundary conditions on the dynamic response of the structure. The results indicated that applied NFRP layer decreases the maximum dynamic displacement of the structure up to 91 percent. In addition, using nanofibers as reinforcement leads a 35 percent reduction in the maximum dynamic displacement of the structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.345.2-345
• /
• 2002

This paper focuses on the formulation and validation of an automatic strategy for the selection of the locations and directions of strain gauges to capture at best the modal response of a blade in a series of modes. These locations and directions are selected to render the strain measurements as robust as possible with respect to random mispositioning of the gauges and gauge failures. (omitted)