• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.72-75
• /
• 2009

Design and Manufacturing processes of Ti-6Al-4V profiled ring-products were investigated with three-dimensional FEM simulation and experimental analyses. FEM simulation for the ring-rolling process was used to calculate the state variables such as strain, strain rate and temperature. In the simulation results of strain and temperature distributions for a plane ring rolling process, the strain level at the surface area is higher than that at the mid-plane, but the temperature level at the surface area is lower than that at mid-plane due to heat transfer between the workpiece and the work roll. These distributions showed a great influence on the evolution of microstructure in different positions. In order to induce the uniform deformation of the profile ring and reduce the applied load, the final blank was prepared by two-step processes. The mechanical properties of Ti-6Al-4V alloy ring products made in this work were investigated with tensile and impact tests and analyzed with the evolution of microstructures during the ring rolling process.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.3
• /
• pp.69-81
• /
• 1988

The Repeated Load Triaxial and Oedometer Tests to the weathered granite & silty clay soil have been fulfilled to investigate their dynarnic characteristics. The results obtained are summarized as follows ; 1. In the relation between the repeated triaxial compression and the oedometer test, the recoverable strain of weathered granite soil showed a tendency to decrease by the increase of the repeated loads number(N), and that of silty clay showed approximately constant values while the total strain increased continuously. 2. The changes of plastic strain was dependent to the level of deviator stress which is the most important element in the calculation of soil deformation under repeated load condition. And there was a significance of 10% between the level of stress and plastic strain. 3. When the soil was aimost dried or saturated to 100%, the deformation by the repeated loads was small. However the deformation showed peak around the saturation of 50%. 4. When the deformation was predicted by the repeated triaxial load tests of a laboratory, it is desirable to introduce the threshold stress concept in the calculation of deformation of subgrade of the pavement. 5. The improved design equation (Eq. 16) introducing the modulus of conversion(Fo), which is based on the Boussineq' s theory, is considered to be rational in the design of flexible pavement. From the above results, the deformation to the repeated traffic loads could be predicted by the repeated triaxial tests on the pavement materials or undisturbed soil layers, therefore it is think that the durable and econornic pavement could be constructed by reflecting that to the design.

• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.89-96
• /
• 2010

This paper focuses on the effect of creep on the critical compressive strain (CCS) of concrete. The strain of concrete corresponding to the peak compressive stress is crucial in the selection of the ultimate yield strength of the reinforcing bar used in reinforced concrete columns. Among the various influencing factors, such as the creep, shrinkage, loading rate and confinement, the effect of creep and shrinkage is the most significant. So far, investigations into how these factors can affect the CCS of concrete have been rare. Therefore, to investigate the effect of creep and shrinkage on CCS, an experimental (part I) and a parametric study (part II) were conducted, as presented in these papers (part I considers creep effect, part II considers effect of creep and shrinkage). In part I, experiments pertaining to the loading age, loading rate, loading duration and loading and creep levels were conducted to study the effect of these variables on the CCS of concrete. It was found that the effects of the loading rate, loading age, and level and duration on the CCS of concrete were negligible. However, it is very important to consider the effect of creep.

• Archives of Pharmacal Research
• /
• v.21 no.3
• /
• pp.305-309
• /
• 1998

Human cytochrome P450 1A2 is one of the major cytochrome P450s in human liver. It is known to be capable of activating a number of carcinogens such as arylamines and heterocyclic amines. In order to develop the new bacterial mutagenicity test system with human P450, a full length of human P450 1A2 cDNA inserted into pCW bacterial expression vector was introduced to Escherichia coli WP2 uvrA strain which is a well-known E. coli strain for bacterial reverse mutagenicity assay. Expressed human P450 1A2 showed typical P450 hemoprotein spectra. Maximum expression was achieved at 48 hrs after incubating at $30^{\circ}C$ in terrific broth containing ampicillin, IPTG and other supplements. High level expression of P450 1A2 in E. coli WP2 uvrA membranes was determined in SDS-PAGE. The well-known mutagens 2-aminoanthracene and MElQ increased the revertant colonies of E. coli WP2 uvrA expressing human P450 1A2 without an exogenous rat hepatic post-mitochondrial supernatant (S9 fraction) in a dose-dependent manner. The results show that the functional expression of human P450 in bacterial mutagenicity tester strain will provide a useful tool for studying the mechanism of the mutagenesis and carcinogenesis of new drugs and environmental chemicals.

• International Journal of Railway
• /
• v.6 no.3
• /
• pp.112-119
• /
• 2013

A mid-size RC test apparatus (MRCA) equipped with a program is developed that can test samples up to D=10 cm diameter and H=20 cm height which are larger than usual samples used in practice. Using the developed RC test apparatus, two types of crushed trackbed foundation materials were tested in order to get the shear modulus reduction curves of the materials with changing of shear strain levels. For comparison purpose, large repetitive triaxial compression tests (LRT) with samples of height H=60cm and diameter D=30 cm were performed also. Resilient modulus obtained from the LRT was converted to shear modulus by considering elastic theory and strain level conversion and were compared to shear modulus values from the MRCA. It is found from this study that the MRCA can be used to test the trackbed foundation materials properly. It is found also that strain levels of $E_{v2}$ mostly used in the field should be verified considering the shear modulus reduction curves and proper values of $E_{v2}$ of trackbed foundation must be used considering the strain level verified.

• Structural Engineering and Mechanics
• /
• v.17 no.1
• /
• pp.113-140
• /
• 2004

A mixed eight-node hexahedral element formulated via the Hu-Washizu principle as well as the field extrapolation technique is presented. The mixed element with only three translational degrees of freedom at each node can provide extremely accurate and reliable performance for popular benchmark problems such as spacial beams, plates, shells as well as general three-dimensional elasticity problems. Numerical calculations also show that when extremely skewed and coarse meshes and nearly incompressible materials are used, the proposed mixed element can still possess excellent behaviour. The mixed formulation starts with introduction of a parallelepiped domain associated with the given general eight-node hexahedral element. Then, the assumed strain field at the nodal level is constructed via the Hu-Washizu variational principle for that associated parallelepiped domain. Finally, the assumed strain field at the nodal level of the given hexahedral element is established by using the field extrapolation technique, and then by using the trilinear shape functions the assumed strain field of the whole element domain is obtained. All matrices involved in establishing the element stiffness matrix can be evaluated analytically and expressed explicitly; however, a 24 by 24 matrix has to be inverted to construct the displacement extrapolation matrix. The proposed hexahedral element satisfies the patch test as long as the element with a shape of parallelepiped.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.5
• /
• pp.613-618
• /
• 1999

L-Proline-producing mutant strains were developed by exposing L-glutamic acid-producing bacteria to N-metyl-N-nitro-nitrosoguanidine and UV irradiation. A L-histidine auxotroph of Corynebacterium acetoacidophilum RYU3161(KCTC 0616BP), which was resistant to sulfaguanidine and proline analogs (DHP, AZC, TAC), was isolated. The activity of the mutant strain's $\gamma$-glutamyl kinase was 45% higher than that of the parent strain. The optimum level of L-histidine for production of L-proline was 0.16 g/l. In a 5-1 jar fermenter, the mutant strain produced L-proline at a high concentration (35 g/l) level within 48 h of cultivation.

• Steel and Composite Structures
• /
• v.27 no.1
• /
• pp.89-94
• /
• 2018

Uniaxial ratcheting behavior of Z2CND18.12N austenitic stainless steel used nuclear power plant piping material was studied. The results indicated that ratcheting strain increased with increasing of stress amplitude under the same mean stress and different stress amplitude, ratcheting strain increased with increasing of mean stress under the same stress amplitude and different mean stress. Based on least square method, a suitable method to arrest ratcheting by loading the materials was proposed, namely determined method of zero ratcheting strain rate. Zero ratcheting strain rate occur under specified mean stress and stress amplitudes. Moreover, three dimensional ratcheting boundary surface graph was established with stress amplitude, mean stress and ratcheting strain rate. This represents a graphical surface zone to study the ratcheting strain rates for various mean stress and stress amplitude combinations. The graph showed the ratcheting behavior under various combinations of mean and amplitude stresses. The graph was also expressed with the help of experimental results of certain sets of mean and stress amplitude conditions. Further, experimentation cost and time can be saved.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.3
• /
• pp.15-19
• /
• 2003

For the purpose of standardization of the critical current measurement, it is meaningful to describe how $I_{c}$ will behave as the stress/strain level changes. In this study, strain dependencies of the critical current $I_{c}$ in Ag-alloy sheathed multifilamentary Bi(2212) and Bi(2223) superconducting tapes were evaluated at 77K, 0T. The external reinforcement was accomplished by soldering AgMgNi alloy tapes onto single or both sides of the sample. With the external reinforcement to the Bi(2212) tape, the strength of the tapes increased but the critical current at the strain free state, $I_{c0}$ decreased in some cases. The strain for onset of the $I_{c}$ degradation, $\varepsilon$$_{\irr}$, increased with an increase of the reinforcing volume and then saturated to a certain value. The effect of external reinforcement on the degradation of $I_{c}$ due to the bending strain in the Bi(2223) tape was also examined. Contrary to the expectation, it showed a significant $I_{c}$ degradation even at a small strain of 0.4 %. The observations of damage morphologies gave a good explanation to the $I_{c}$ behavior.c/ behavior.r.

• Journal of Families and Better Life
• /
• v.23 no.6 s.78
• /
• pp.117-131
• /
• 2005

In this paper, 1 examined role gratification and role strain of South Korean working mothers. The results show that South Korean working mothers experienced very similar level of role gratification and role strain as taking their multiple roles. The findings also show that the factors of caregiving demands, employment demands, caregiving resources, employment resources are not strongly related to role gratification and role strain. Among the 12 caregiving demand variables and employment demand variables, number of children, type of family, number of hours worked were significantly related to producing role gratification. Among the 12 caregiving demand variables, number of hours worked, number of husbands absence due to night work were significantly related to producing role strain. Among the 8 caregiving resources, participants satisfaction due to income contribution, look to make a purchase new electric home appliances were significantly related to produce role satisfaction. Among the 8 caregiving resources, number of family support policies in the husbands workplace, participants satisfaction due to income contribution were significantly related to producing role strain.