• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.42-47
• /
• 2010

Polymer insulating materials such as cross linked polyethylene (XLPE) are employed in electric cables used for extra high voltage. These materials can degrade due to chemical, mechanical and electric stress, possibly caused by voids, the presence of extrinsic materials and protrusions. Therefore, this study measured discharge patterns, discharge phase angle, quantity and occurrence frequency as well as changes in XLPE under different temperatures and applied voltages. To quantitatively analyze the irregular partial discharge patterns measured, the discharge patterns were examined using a statistical program. A three layer sample was fabricated, wherein the upper and lower layers were composed of non-void XLPE, while the middle layer was composed of an air void and copper particles. After heating to room temperature and $50^{\circ}C$ and $80^{\circ}C$ in silicone oil, partial discharge characteristics were studied by increasing the voltage from the inception voltage to the breakdown voltage. Partial discharge statistical analysis showed that when the K-means clustering was carried out at 9 kV to determine the void discharge characteristics, the amount discharged at low temperatures was small but when the temperature was increased to $80^{\circ}C$, the discharge amount increased to be 5.7 times more than that at room temperature because electric charge injection became easier. An analysis of the kurtosis and the skewness confirmed that positive and negative polarity had counterclockwise and clockwise clustering distribution, respectively. When 5 kV was applied to copper particles, the K-means was conducted as the temperature changed from $50^{\circ}C$ to $80^{\circ}C$. The amount of charge at a positive polarity increased 20.3% and the amount of charge at a negative polarity increased 54.9%. The clustering distribution of a positive polarity and negative polarity showed a straight line in the kurtosis and skewness analyses.

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.23-28
• /
• 2003

The effect of the welding speeds on the weld bead shape, microstructure, and mechanical properties in type 304 austenitic stainless steels was investigated by microscopic test, Erichsen test and tensile test. In this study welds were produced using autogeneous Direct Current Straight Polarity (DCSP) and pulsed current GTA welding. This study shows the ferrite content, ductility, tensile strength and elongation of high speed welds are decreased with increasing welding speed. The high speed welds exhibits satisfactory tensile strength, though the ductility is not good as that of the base metal.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.70.2-70.2
• /
• 2019

Recent observational works have reported spiral wave patterns (SWPs) in sunspots, but there is a lack of samples to derive the physical properties. In this presentation, we suggest the automatic method to detect the SWPs in observational data and present their statistical properties. From our method, we find more than 1000 SWPs observed by the Atmospheric Imaging Assembly onboard in the Solar Dynamic Observatory from 2013 to 2018. From our samples, more than half of the SWPs has the one spiral arm. The predominant oscillation period is 2 to 3 minutes. The rotating direction of the spiral arms does not depend on the latitude and the polarity of the sunspots. Our statistical results support the physical model suggested by Kang et al. (2019) that explain the generation of SWPs as the depth of the wave driving source and azimuthal modes in the straight vertical magnetic flux tube.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.2
• /
• pp.45-50
• /
• 2004

The field utilization factor (equation omitted) (the mean electric field / the maximum electric field) of standard sphere gaps was calculated by the charge simulation method, taking into account the ground plane and shanks. n changes mainly with g/r and slightly with 1$_1$, 1$_2$ and 1, where D=2r is the sphere diameter, g is the gap length, 1$_1$ and 1$_2$, respectively, are the lengths of the upper and lower shank, and t is the shank diameter. Generally, (equation omitted) increases as 1$_1$,1$_2$ and t each becomes larger. IEC standard 60052(2002) limits t$\leq$0.2D 1$_1$$\geq$1D and prescribes A=1$_2$＋D＋g where A is the height of the spark point on the upper sphere. Therefore, (equation omitted) is the largest when A=9D and the smallest when A=3D. The simple equation of a straight line, (equation omitted)=1- (g/3r), can generally be used as a representative value of (equation omitted) for a wide variety of sphere diameters that are permitted by the IEC standard. The maximum electric field E$_{m}$ at sparkover of standard air gaps has also been calculated by the relation E$_{m}$=V/(equation omitted)g). E$_{m}$ describes a U-curve for g/r, up to the sphere diameter of 1 m. Moreover, for 1.5-m and 2-m diameters and especially .for negative polarity, sparkover voltages have been calculated by integration of the ionization index.index.

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.29-33
• /
• 2003

The ferritic stainless steels are generally considered to have poor weldability compared with that of the austenitic stainless steels. However the primary advantages of ferritic stainless steels include lower material cost than the more commonly used austenitic stainless steels and a greater resistance to stress corrosion cracking. Thus, the weldability of ferritic stainless steels was investigated in this study. In concerning the weldability, Grain size measurement test, Erichsen test and Varestraint test were involved. full penetration welds were produced by autogeneous direct current straight polarity (DCSP) and pulsed currents gas tungsten arc welding (GIAW) and the effect of pulsed currents welding on the welds was compared to that of DCSP welding. The results showed that pulsed current was effective to refine grain size in the weld metal and the finest grain size was obtained at the frequency of 150Hz. In addition, the ductility of welds was lower than that of base metal. Finally, autogeneous type 444 welds were less susceptible to macro solidification cracks, but more sensitive to micro cracks; SEM/EDS analysis indicated that all the inclusions in the crack showed enrichment of Mn, Si, O and S.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.89-93
• /
• 2002

A study of noticeable improvement in welding speed in thin-plate Type 304 stainless steels gas tungsten arc (GTA) welding was investigated. The welding speeds were increased to more than 3m/min, up to 8m/min. During the welding, Direct Current Straight Polarity (DCSP) and pulsed current GTA welding processes were carried out, respectively. The appropriate high speed welding parameters were established while achieving a high quality weld. After this, Erichsen test and tensile test were performed. The results obtained wert summarized as following: ultra high speed welding for thin-plate Type 304 could be satisfactorily welded with high speed from 3m/min to 8m/min in both DCSP and pulsed GTA welding; Increasing welding speed was found to decrease the ductility, tensile strength md elongation of welded joint; The optimal frequency would be 200Hz-500Hz for high speed welding in pulsed current welding; DCSP welding could obtain the better results of Erichsen test and tensile test than those of pulsed current welding obtained.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.107-112
• /
• 2002

Ferritic stainless steels would be the most important alloys under the chloride environment. They are a cheaper alternative to austenitic stainless steels [1]. The present study is related to gas tungsten arc welding (GTAW) characteristics of Type 444 stainless steels. The heat of welding leads to grain coarsening in the HAZ and in the weld metal of ferritic stainless steels because they solidify directly from the liquid to the ferritc phase without any intermediate phase transformation. It is therefore recommended that these alloys be welded with a low heat input and at high welding speeds. Attempts to improve weldability were made by using of direct current straight polarity (DCSP) and pulsed current GTAW processes in this study. Measuring weld bead, grain size and Erichsen test were performed and the effects of heat input, pulse frequency on the weld metal and HAZ were studied. The main results were obtained as followings: decreasing heat input was effective to control the width of weld both in DCSP welding and in pulsed current welding; pulsed current welding was found to refine the grain size effectively and the finest grain size was found at the frequency of 150Hz in pulsed current welding; it was found that decreasing heat input also refine the HAZs effectively and the frequency had no different effect on HAZ at the same heat input; the ductility could be improved effectively in pulsed current welding.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.4
• /
• pp.309-316
• /
• 2001

Helianthus tuberosus has been known to inhibit the growth of weeds and other plants sharing its habitat. This study was conducted to identify the allelochemicals of Helianthus tuberosus which were extracted with water and solvents. Aqueous extracts of leaf, stem, root, tuber and tuber peel of Helianthus tuberosus except tuber did not show significant differences in phytotoxicity to alfalfa seedlings. It was considered that Helianthus tuberosus contained fewer or less potential water-soluble substances that were toxic to alfalfa. Methanol extract of leaves of Helianthus tuberosus was sequentially partitioned in increasing polarity with n-hexane, ethylacetate and n-butanol. Each extract had a yield of 148, 12, 15.7 and 9.5g, respectively. Inhibitory effects on germination of alfalfa seeds treated with four fractions were not significantly different. But the significant reductions on hypocotyl length were observed for all the solvent extracts. Among the four fractions, the ethylacetate fraction showed the most significant inhibition effect on bioassay with alfalfa. Further separation of the active ethylacetate fraction by open column chromatography led to the 25 subfractions. In bioassay of each sub-fraction with alfalfa seeds, sub-fraction No. 13 showed the most inhibitory effect on seedling growth. $^1$H NMR and gas chromatography-mass spectrometry analysis revealed that sub-fraction No. 13 was the mixture of straight-chain saturated fatty acids.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.2
• /
• pp.38-43
• /
• 2015

Tungsten inert gas (TIG) welding is commonly used in industries that require airtightness, watertightness, oiltightness, and precision. It is a non-consumable welding method that is commonly used for the welding of non-ferrous metals, but it can be used to weld most metals. The methods of TIG welding can be divided into three types. The first, manual welding is done directly on the metal by a welder with a torch. The second, semi-automatic welding, gets help from a material supplying machine, but it is conducted by a welder. Lastly, automated welding is conducted fully by a machine during its process and operation. Depending on the selection of electrode, the amount of heat that is applied to the base material and the electrode rod changes and makes the shape of welded parts different. A direct-current positive electrode was used for this study. Through the change of shielding gas type on a structural steel (SS-400) that is commonly used in industry, the composition and shape changes in welded parts were detected after welding. The heat-affected area, hardness value, and tensile strength were also identified through hardness testing and tensile testing. In this study, it was found that the higher hardness value of the heat-affected is, the weaker the tensile strength becomes.

• Analytical Science and Technology
• /
• v.18 no.3
• /
• pp.194-200
• /
• 2005

The N hyperfine coupling constants ($a_N$) of di-t-butyl nitroxide (DTBN) radicals in water-solvent system were measured with EPR spectroscopy. Various kinds of the solvents with different polarity such as acetone, dimethylsulfoxide (DMSO), methanol, ethanol and 1-propanol were applied and studied. Equilibrium constants for the solvation equilibrium and the solvent parameters ($E_T$, molar transition energy) of various water-solvent system were obtained from the experimental results and are presented. The $a_N$ values were plotted as a function of mole fraction of the solvent. In case of water-DMSO, water-ethanol and water-1-propanol system, slight negative deviations from the straight line were observed. In water-acetone system, the absorption wavelength (${\lambda}$) due to ${\eta}{\rightarrow}{\pi}^{\ast}$ transition increased linearly with the increase of mole fraction of acetone. The relationship between $a_N$ of DTBN and ${\lambda}$ due to ${\eta}{\rightarrow}{\pi}^{\ast}$ transition in water-acetone and water-DMSO system was examined. It was found that the electronic structure of the nitroxide radicals is stablized from the fact that the N hyperfine coupling constants of DTBN radicals are greatly unaffected in the environment of water-solvent system.