• Journal of Pharmaceutical Investigation
• /
• v.12 no.3
• /
• pp.55-63
• /
• 1982

The dissolution kinetics for polymorphs of sulpiride, the effect of polyethylene glycol 4000 on the dissolution kinetics of sulpiride polymorphs and the dissolution rate difference between the tablets of polymorph form I and form II were investigated. The results could be summerized as followings: 1. The dissolution rates of two polymorphs of sulpiride were significantly different and the thermodynamic parameters calculated from dissolution kinetics were as follows; transition temperature $98^{\circ}C$, enthalpy change, -2.108 kcal/mole, free energy change, -783 cal/mole $(31.0^{\circ}C)$. 2. The dissolution rates of the two polymorphs of sulpiride containing polyethylene glycol 4000 were significantly diefferent in 0.01N HCl but the effect of polyethylene glycol on the dissolution rates of two polymorphs was not significant at low concentration of polyethylene glycol 4000. The study on the effect by stirring speed showed that at lower stirring speed the promotion rate of dissolution of polymorph form I is greater than that of form II. 3. In the case of tablets the dissolution rates of polymorph form I of sulpiride was two fold as compared with the results obtained from form II.

• Membrane and Water Treatment
• /
• v.4 no.4
• /
• pp.277-291
• /
• 2013

The transport and recovery of Levafix brilliant red E-4BA and Levafix brilliant red E-6BA were investigated using polytetrafluoroethylene (PTFE) fiber based supported liquid membrane containing tetra butyl ammonium bromide (TBAB) in coconut oil as a carrier. The influencing parameters studied are: pH of the feed solution, concentration of dye in the feed solution, extractant concentration, and various kind of stripping agent, rate of stirring, time of transport, reusability of membrane and stability of membrane. Increase in TBAB concentration inside the membrane enhances the flux with its maximum value at $1.553{\times}10^{-4}$ M TBAB. Further increase in the concentration of TBAB leads to decreased rate of transport due to increase in viscosity of membrane liquid. The optimum conditions for dye transport are: pH of feed ($7{\pm}0.1$), $1.553{\times}10^{-4}$ M extractant concentration, 350 rpm for stirring, $4.9{\times}10^{-1}$ M potassium hydrogen phthalate as a stripping solution, the time of transport 6 h. It was noticed that flux values were increased with increasing dye concentration in the feed phase. Applying this study to textile wastewater, dyes were transported up to 98% in 6 h. This recovery technique is rewarding to environment and economic.

• KSBB Journal
• /
• v.19 no.3
• /
• pp.226-230
• /
• 2004

Fermentation characteristics of D-xylose into xylitol by Candida mogii ATCC 18364, a potential xylitol producer from rice straw hemicellulose hydrolyzates, were investigated. The influences of the most important operational variables on xylitol production were examined. The best results in xylitol production were obtained in shake-flask fermentations when 3.0 g/L initial cell concentration of 12 hr-old cells grown in D-glucose containing medium were used as inoculum. The oxygen availability is a critical factor in xylose fermentation, therefore, xylose conversion into xylitol was investigated in a 2-L fermenter at different stirring rates. Maximum xylitol production was obtained with an aeration rate of 1 vvm at a stirring rate of 200 rpm.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.11
• /
• pp.1374-1378
• /
• 2009

Response surface methodology (RSM) examining the effects of five-level-three-factors and their mutual interactions was utilized to optimize the fermentation conditions to enhance capsular polysaccharide (CPS) production of Streptococcus pneumoniae type 3. Twenty experiments conducted in an 8-l lab-scale fermentor were designed to assess fermentation pH, supplemented glucose concentration, and stirring rate. The predicted highest CPS production by the obtained optimization model equation was 256.14 mg/l at optimal conditions [pH 7.5, stirring rate 180 rpm, and supplemented glucose concentration 1% (w/v)]. The validity of the response model was confirmed by the good agreement between the predicted and experimental results. The maximum amount of CPS obtained was $255.03\pm2.23$ mg/l.

• Journal of Pharmaceutical Investigation
• /
• v.29 no.4
• /
• pp.315-321
• /
• 1999

Poly (lactide-co-glycolide) (PLGA) microspheres containing ovalbumin (OVA) as a model protein drug were prepared by double emulsification method, and various conditions such as mixing rate, volume of outer phase and isopropyl alcohol concentration in outer phase during secondary emulsification were observed to control the size of microspheres. In addition, entrapment efficiency of OVA and protein denaturation were also evaluated. As the rate of stirring was increased, the size of particles was decreased. But excessive stirring increased the particle size of microspheres. In a preparation condition of small volume of outer phase, the particle size was decreased but the entrapment efficiency was increased. Adding isopropyl alcohol to outer phase decreased the size of particles, but increased the entrapment efficiency. Microparticles should have smaller size than $10\;{\mu}m$ to be uptaked by Peyer's patch in small intestine. High speed of mixing and relatively small volume of outer phase are needed to reduce the size. In addition, appropriate amount of isopropyl alcohol in outer phase also plays an important role in size reduction of PLGA microspheres.

• Journal of the Korean Applied Science and Technology
• /
• v.18 no.4
• /
• pp.273-284
• /
• 2001

A series of microcapsule were synthesized by using several PCM(Phase Change Material) as a core material and gelatin/arabic gum, melamine/formaldehyde as a shell material. Coacervation technique and in situ polymerization were adopted in synthesizing microcapsules. In the microencapsulation by coacervation, tetradecane and octadecane were used as core materials. In the microencapsulation by situ polymerization tetradecane, pentadecane, hexadecane, heptadecane, octadecane, and nonadecane were used as core material. The synthesized microcapsule was examined to observe the shape of the microcapsule. The particle size analysis was performed by particle size analyzer. The thermal properties(e.g. melting point, heat of melting, crystallization temperature, heat of crystallization, differences between melting point and crystallization temperature) were obtained by DSC(Differential Scanning Calorimeter). The stirring rate effect was investigated during the microencapsulation. It was found that with increasing the stirring rate much smaller microcapule was produced. However, this did not necessarily lead to formation of spherical microcapsule.

• Corrosion Science and Technology
• /
• v.22 no.6
• /
• pp.457-465
• /
• 2023

Irradiation-assisted stress corrosion cracking (IASCC) is one of the main degradation mechanisms of austenitic stainless steels, which are used as reactor internal materials. Slow strain rate testing (SSRT) has been widely applied to evaluate the IASCC initiation characteristics of proton-irradiated tensile specimens. Tensile specimens require low surface roughness for micro-crack observation, and electropolishing is the most important specimen pre-treatment process used for this. In this study, optimal electropolishing conditions were examined through analyzing results of polarization experiments and surface roughness measurements after electropolishing. Corrosion cell and electropolishing equipment were fabricated for polarization tests and electropolishing experiments using SSRT specimens. The experimental parameters were electropolishing time, current density, electrolyte temperature, and stirring speed. The optimal electropolishing conditions for SSRT tensile specimens made of type 316 stainless steel were evaluated as a polishing time of 180 seconds, a current density of 0.15 A/cm², an electrolyte temperature of 60 ℃, and a stirring speed of 200 RPM.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.34-39
• /
• 2022

In this study, effects of ultrasonic energy on the cementation reaction and copper recovery rate were investigated for different types of iron samples, such as plate, chip, and powder, for recovering copper from waste etchant, which contained ~3.5% copper. The cementation reaction using the ultrasonic energy was more effective than the simple stirring reaction, with the former exhibiting a high copper recovery rate than the latter for the same time interval. When cementation was performed for 25 min with ultrasonic treatment, rather than simple stirring, the copper recovery rate of the plate, chip, and powder improved from 7.0% to 12.0%, 14.0% to 46.1%, and 41.9% to 77.2%, respectively. Therefore, the use of ultrasonic energy could detach the copper recovered by the cementation reaction from the surface of the iron samples, thereby increasing the copper recovery rate. Owing to the use of ultrasonic energy, the copper recovery rate increased by 2-6 times, and the recovered copper exhibited a decreased particle size compared to that obtained via simple stirring.

• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.469-474
• /
• 2001

Milling the rice with low moisture requires more energy, produces more cracked rice, and results in reducing taste of cooked rice. Accordingly, it is necessary to add moisture to the rice with low moisture to obtain optimum moisture level for milling and taste of rice. This study was performed to evaluate the influence of initial moisture content and absorption rate on rice crack, milling energy and whiteness of milled rice and to obtain the information for design of rewetting system mounted on stirring device in grain bin. The tests were conducted for the four levels of initial moisture content in the range of 11.4 to 14.5%(w.b.) and six levels of absorption rate in the range of 0.04 to 1.0%, w.b./hr. In the case of lower moisture content below 12%(w.b.), crack ratios of brown rice were remarkably high regardless of initial moisture contents. Therefore, it was found that rough rice below 12%(w.b.) in initial moisture content could not rewetted by spraying water without crack generation of low level. Absorption rate must be below 0.3%, w.b./hr to maintain crack ratio increase of less than 1% regardless of initial moisture contents. In the case of allowable crack ratio increase of 2% and 5%, it was found that the maximum absorprion rate was respectively 0.6%, w.b./hr and 1.0%, w.b./hr in the initial moisture content of above 13.5%(w.b.). Rewetting the rough rice in moisture content of 11.4 to 14.5%(w.b.) to 14.3 to 16.9%(w.b.) decreased milling energy consumption by 15.9 to 22.3%. The effect of energy saving was higher in the samples of higher initial moisture content. Whiteness of milled rice was decreased by 0.5 to 1.5.

• Resources Recycling
• /
• v.25 no.6
• /
• pp.65-72
• /
• 2016

We studied a selective recovery condition of vanadium (V) from FALL (Fly Ash Leach Liquor) produced at a fossil fuel power station using heavy oil. By applying a spectroscopy to quantify the V in a sample, we identified a concentration range V interfered by on presence of metals such as Ni, Fe Also, the optimal vanadium precipitation rate according to the amount of 5.0M $NH_3$ loaded to the sample, solution pH and stirring time. As a result of the experiment, the maximum selective recovery ratio of V was achieved to be higher than 91.5% when the stirring duration was less than 1 minute at pH 7.0, and $25^{\circ}C$.