• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.4
• /
• pp.74-81
• /
• 2008

The writing brush, ink stick, paper, and ink stone were the four precious things of the studying and recording in oriental world until even nowaday. The oriental paper was comparatively well evaluated in many papers and reviews, but it is difficult to find some scientific reports or reviews about the ink stick. In this paper, the scientific aspect of ink sticks of oriental maine three country(Korea, China, Japan) were evaluated by the physical, chemical and microscopic analysis. The result could summarized as fellows; 1. The Korean lampblack ink stick contains more carbon and less nitrogen and the Chinese ink sticks contain less carbon and more oxygen. 2. The Korean lampblack and cowhide glue contain relatively higher amount of sulphur. 3. The particle size distribution of carbon in the ink stick was not change after grinding in the ink stone. 4. The particle size of carbon and the pore size in the charcoal ink sticks of three country were larger than those of the lampblack ink sticks. 5. The ink solution of the charcoal ink sticks shows high roundness on Hanji while the ink solution of the lampblack ink sticks is spread readily to Hanji surface. 6. The change of whiteness in printing of the ink sticks is notable in thermal treatment.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.1-6
• /
• 2005

Stick type ignition coil is new development that connect directly with ECU(Electronic control unit), without needing a spark plug cable and distributor. Glass-fiber reinforced ploymeric composites provide the desirable properties of high stiffness and strength as well as low specific weight. Stick type ignition coil jacket is using PBT CF30 resin. PBT CF30 resin is a kind of electric insulation which is a superior engineering plastic that is used to prevent the leakage of the electrical current. If PET receive a mistake of design or excessive force when HV terminal oppress on jacket, it can happen to crack. Local stress concentrations occurring on the contact surface, the contact phenomenon becomes a direct cause to the wear and failure of mechanical structures. When it is cracked, it can allow a leakage of the electrical current. So, in this study, we analyze the contact stress to PBT jacket using ANSYS program, when HV terminal oppress on jacket. We suppose PBT to be Jacket and we analyzed contact stress that happens in PET like PBT analysis method. We compared the use of PBT and PET.

• Journal of Preventive Medicine and Public Health
• /
• v.27 no.3 s.47
• /
• pp.403-409
• /
• 1994

A questionnaire survey wds conducted to assess the experience of the needle stick injury in 144 seniors of a medical school during the previous 10 months. One hundred and five of them (73%) had responded. About sixty-nine percent (72 cases) of the respondents had suffered at least one u and there had been 129 injuries in total. Seventy-eight (56.6%) of the injuries took place at the time of the venipuncture. The emergency and operating room incurred 76.7% and 23.3% of the injury, respectively. Injuries with bleeding account for 50.4%. None of the respondents was systematically educated about the prevention of injury. This survey shows that the needle-stick Injury is a great risk for the medical students' health, and that educational effort for its prevention is warranted.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1398-1402
• /
• 2015

In surface mount technology, the use of technology implemented using a Chip Mounter relay that is inserted into the junction box, etc. car is increasing. On the other hand, there is a need for technology to reduce the weight of the heavy component of the relay attached to different Stick Tube generally chips. Therefore, rather than existing technology, this study improved the algorithm of the system to provide a mechanical structure using Air to supply greater stability using this the component feeder utilizing the Stick Tube proposed technology. When the equipment installed in the Air Stick Feeder was used, the effectiveness, such as increased production and reduced disposal expense, was improved.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1134-1142
• /
• 2008

In this paper, a model-based stick-slip compensation for the micro-positioning is proposed using an enhanced stick-slip model based on statistical rough surface contact model. The smart structure is comprised with PZT(lead (Pb) zirconia(Zr) Titanate(Ti)) based stack actuator incorporating with the PID(proportional-integral-derivative) control algorithm, mechanical displacement amplifier and positioning devices. For the stick-slip compensation, the elastic-plastic static friction model is used considering the elastic-plastic asperity contact in the rough surfaces statistically. Mathematical model of system for the positioning apparatus was derived from the dynamic behaviors of structural parts. PID feedback control algorithms with the developed stick-slip model as well as feedforward friction compensator are formulated for achieving the accurate positioning performance. Experimental results are provided to show the performances of friction control using the developed positioning apparatus.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.23 no.4
• /
• pp.231-238
• /
• 2019

A conventional lumped-mass stick model is based on the tributary area method to determine the masses lumped at each node and used in earthquake engineering due to its simplicity in the modeling of structures. However the natural frequencies of the conventional model are normally not identical to those of the actual structure. To solve this problem, recently an updated lumped-mass stick model is developed to provide the natural frequencies identical to actual structure. The present study is to investigate the seismic response accuracy of the updated lumped-mass stick model, comparing with the response results of the shaking table test. For the test, a small size four-story steel frame structure is prepared and tested on shaking table applying five earthquake ground motions. From the comparison with shaking table test results, the updated model shows an average error of 3.65% in the peak displacement response and 9.68% in the peak acceleration response. On the other hand, the conventional model shows an average error of 5.15% and 27.41% for each response.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.233-236
• /
• 1996

This paper describes a liner state-space model for a flexible stick balencer. The method employed to generate the model utilizes a separable formulation of assumed modes to represents the transverse displacement due to bending Lagrangian dynamics are applied to determine the kinetic and potential energies for the system. The resultant dynamic equations are then organized into a state space model and linearized using Taylor series expansion method. A minimum order observer is designed to estimate unmeasurable states.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.488-490
• /
• 2015

In this paper, the selfie stick which can involved in small bag is designed to make easier and smaller. Model the diameter of the selfie to achieve light weight for the fixed length using FreeCAD. After modeling, check durability using 'Netgen' and 'Calculix'.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.2
• /
• pp.76-82
• /
• 2006

High-strength, High-durability concrete appearance was embossed by benevolence who quality for each raw material that become factor that is direct in concrete manufacture and the special quality is very important and request properties of matter were also strengthened more. Specially, natural resources of good quality were abundant past in occasion of aggregate and unlike concrete request strength past that the importance was less relatively the quality enemy than cement because is also not big, importance of aggregate quality great veried as concrete strength and request properties of matter about durability are strengthened more on extreme displacement. Mixing four who is original and mixs special quality examination of domestic three Four-Stick Games by Chaechwiwon and age Four-Stick Games and crushed sand examined concrete quality characteristic that use mortar and concrete quality characteristic, special quality of North Korea sun guardian mountain three Four-Stick Games that is imported from the North Korea, North Korea sun guardian mountain three Four-Stick Games etc..

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.1-15
• /
• 1998

Currently, computational analysis is a popular technology in automobile engineering. Finite element analysis is an excellent method for body analysis. For finite element analysis, accurate modeling is very important to obtain precise information. Stick modeling is a convenient way in that it is easy and simple. When a stick model is utilized, the joints are modified in the tuning process. A tuning method for the joint has been developed. The joints are modeled by designated beam elements. An optimization method called "Goal Programming" is employed to impose the target values. With the tuned joints, the entire optimization has been carried out. Using the "Recursive Quadratic Programming" algorithm, the optimization process determines the configuration of the entire structure and sizes of all the sections. For example, the structure of an electrical vehicle is modeled and analyzed by the method. The stick model works well since the structure is made of aluminium frames. Although the example handles an electrical vehicle, this method can be applied to general vehicle structures.