• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.60-64
• /
• 2001

We have studied properties of step-edge Junction prepared with crystal orientation of sapphire substrate. The Step on sapphire substrates fabricated by conventional photolithography method and Ar ion milling method. $CeO_2$ buffer layer and in-situ YBCO thin film were deposited on the stepped sapphire substrates by a pulsed laser deposition method with the predetermined optimized condition. The step angle was centre fled low angle of about $25^{\circ}$. The YBCO film thickness was varied to obtain various thickness ratios of the film to the step height in a range from 0.7 to 1.2. I-V curves of junction were showed RSJ-behavior, double junction structure, and hysteresis due to the crystal orientation of substrate.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.4
• /
• pp.55-66
• /
• 2005

The present study used a video analysis system to quantify the kinematical data of step shoot motion by male university handball players. From the results of analyzing dynamic variables of step shoot motion according to shooting direction were drawn conclusions as follows. 1. The height of release was proportional to the height of players, and the height of release appeared low in left-side attacks. This is probably because the left-right-throwing angle is larger in left-side attacks than that in center attacks and right-side attacks and, as a result, the throwing arm is lowered down in throwing. 2. The leftward inclination angle of the body was larger in order of right-side attacks > center attacks > left side attacks. 3. Players' throwing form was close to three quarter style in left-side attacks. In center and right-side attacks, the arm was somewhat more upright but still it was more three quarter style than overhand style. 4. The front-rear throwing angle at the moment of release was much higher in right-side attacks than in left-side ones. This is probably because the point of time for releasing the ball is usually late in right-side attacks and, as a result, the front-rear throwing angle becomes quite large. 5. The contribution of body parts on the ball speed was higher in order of the forearm > upper arm, hand > shoulder joint. 6. In players whose distance between the two legs at the moment of release, their body usually did not incline to the side much. Thus it is considered necessary to correct the right leg in their shooting motion. 7. According to the result of analyzing throwing form, the speed of the ball at the moment of leaving the hand was faster in right-side attacks than in left-side and center attacks.

• Transactions of Materials Processing
• /
• v.24 no.6
• /
• pp.387-394
• /
• 2015

Air springs are designed to support loads using the volume elasticity in a cylindrical shaped air bag made of a composite material with a rubber matrix and two plies of reinforced fibers. Recently, applications of these springs have been expanded from railway vehicles to passenger cars. The current study presents a finite element analysis of a manufactured air spring for a passenger car. The analysis was conducted including the mounting steps of the air bag using a static loading condition. A method for controlling the internal pressure and displacements during the mounting step was developed. The characteristic load curve and the shape of the air bag were in good agreement with the experimental data with respect to the design height, the bump height and the rebound height. Results indicate that ply angles of fibers vary from 38 degrees to 56 degrees during static loading.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.1
• /
• pp.43-49
• /
• 2019

In this paper, we introduced phase optimization techniques in the Soil-Nail design to optimize the reinforcement required for each grade level. The optimal design results at the maximum slope height were further amplified to allow for phase optimization of the horizontal spacing of the Nail in accordance with the change in the height of the slope. The limit equilibrium analysis was performed by step-by-step sloping height, and the safety factor exceeded when the horizontal spacing of four days was fixed. The process of optimization was effectively carried out by densifying the required reinforcement depending on the slope elevation. Also limited to reflect the axial force of the nail into the reinforcement details.Using the method, the members' strength was reflected. When phase optimization technique is applied for each slope height by calculating the stiffening precision, it is judged that it will be more economical to optimize horizontal intervals by effectively reducing the repeated reinterpretation process that satisfies the reference safety ratio for each slope height.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.59-65
• /
• 1999

This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.28-35
• /
• 2002

In cavity flow, the rectangular step generates so strong sound that many researchers have investigated method to suppress the nois during interaction between vortical flow and rectangular forward step. In this study the flow noise from the vortex motion in two-dimentional low Mach number flow past a forward step with various chamfering angle is calculated numerically. Inviscid incompressible discrete vortex model and matched asymptotic expansion(MAE) theory are applied to obtain the inner flow field and the outer noise field. Both source acoustic pressure and sound intensity are obtained with various chamfering height, chamfering angle and initial vortex position. The pressure amplitude is most suppressed when the chamfering angle is between $15^{\circ}C$ and $30^{\circC}$ at the chamfering length of 30% of the step height.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.215-220
• /
• 2005

When the fuel jet velocity is smaller than coflow velocity, the trend of decreasing liftoff height of highly diluted propane lifted flame with coflow velocity is observed experimentally. To investigate the mechanism of decreasing liftoff height with coflow velocity, lifted flames in propane jet has been studied numerically. Using one-step overall reaction mechanism the liftoff heights have been calculated for four cases of coflow velocity. The simulation agrees qualitatively with experimental observation that the liftoff height decreases with coflow velocity. As coflow velocity increases, the streamlines between nozzle and lifted flame diverge in radial direction due to the difference of momentum between coflow jet and fuel jet such that the local flow velocity ahead of lifted flame base decreases resulting in decrease of the liftoff height with coflow velocity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.935-938
• /
• 1997

Recently, the minimum line width shows a tendency to decrease and the multi-level increase in semiconductor. Therefore, a planarization technique is needed and chemical mechanical polishing(CMP) is considered as one of the most suitable process. CMP accomplishes a high polishing performance and a global planarization of high quality. But there are several defects in CMP such as micro-scratches, abrasive contaminations, and non-uniformity of polished wafer edges. Wet etching include of Spin-etching can improve he defects of CMP. It uses abrasive-free chemical solution instead of slurry. On this study, ILD(INterlayer-Dielectric) was removed by CMP and wet-etching methods in order to investigate the superiority of wet etching mechanism. In the thin film wafer, the results were evaluated at a viewpoint of material removal rate(MRR) and within wafer non-uniformity(WIWNU). And pattern step height was also compared for planarization characteristics of the patterned wafer.

• Journal of Magnetics
• /
• v.2 no.3
• /
• pp.67-71
• /
• 1997

A new hot-forming process has been studied to produce anisotropic Nd-Fe-B based magnets from melt-spun ribbons. The ribbon fragments were inserted in a Cu tube and hot-deformed together with one-stroke. At a height reduction ratio of 0.44, the melt-spun ribbons were densified into a magnet with a density of 7.14 g/cm3, and showed a (BH)max of 14.6 MGOe. With further deformation, the magnets were plastically deformed with Cu tubes in the lateral direction, and crystallographic anisotropy was introduced. The magnets with a height reduction ratio of 0.75 exhibited magnetic properties of (BH)max = 32.1 MGOe, Br = 11.7 kG, and iHc = 10.6 kOe. This process shows the possibility that the conventional hot-pressing and subsequent die-upsetting for anisotropic magnets can be simplified into a one-step process.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.773-775
• /
• 2003

From the view point of data fusion, we integrate LIDAR data and digital aerial images to perform 3D building modeling in this study. The proposed scheme comprises two major parts: (1) building block extraction and (2) building model reconstruction. In the first step, height differences are analyzed to detect the above ground areas. Color analysis is then performed for the exclusion of tree areas. Potential building blocks are selected first followed by the refinement of building areas. In the second step, through edge detection and extracting the height information from LIDAR data, accurate 3D edges in object space is calculated. The accurate 3D edges are combined with the already developed SMS method for building modeling. LIDAR data acquired by Leica ALS 40 in Hsin-Chu Science-based Industrial Park of north Taiwan will be used in the test.