• Journal of the Korean Society for Railway
• /
• v.2 no.2
• /
• pp.31-38
• /
• 1999

Two representative types of the AGT (Automated Guideway Transit) system, which are bogie and steering types, are available for the side-guided system. Each system primarily consists of the bogie frame, suspensions, wheelsets and axles, braking system and transmission system. Among these components, the bogie frame is one of the most significant components subjected to the whole vehicle and passenger loads. This paper describes structural analyses and associated fatigue analyses for each bogie frame depending on the various loading conditions on a basis of the railway vehicle code UIC 515-4. Subsequently, comparisons are made between those two types to estimate which type is more reliable in terms of strength and fatigue. It is observed that the bogie type is a little advantageous over the steering one from the strength analysis. However, the two types are found to be in a reliable range of fatigue even though a realistic fatigue load case is further carried out. In addition, an optimal size of thickness is suggested for designs of the bogie frame.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.715-721
• /
• 2007

On a conventional rail vehicle, passive primary suspensions stabilize wheelsets in the longitudinal and yaw direction. However, these suspensions reduce the natural curving ability due to the profile of the wheels. Stabilizing and steering of the wheelsets generate the conflict problems in design process. Therefore, most systems are designed to guarantee the stability in spite of decreased curving performance. As a result, severe wear of the wheels and rails occur on tight curves and squeal noise on curving is high. Active steering has been proposed to satisfy stabilizing and steering performance simultaneously. This paper describes the possibility investigation about the application of the active steering bogie for a urban railway vehicle. Vehicles run on an amount of tight curves at mid or low speed in urban railways. Thus, it is important to reduce the wear and squeal noise between wheels and rails. Simulations show that active steering can be reduce the wear and squeal noise significantly compared to conventional systems.

• Journal of the Korean Society for Railway
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2001

In this paper, the dynamics and stability of the automated guideway transit (AGT) vehicles with rubber tires are investigated. Two types of AGT systems are considered: the bogie-type and steering-type systems. The critical speeds for the dynamic instability of lateral and yawing motions are investigated by use of the Routh-Hurwitz's stability criterion. It is shown that the bogie-type AGT vehicles are likely to be stable within the range of practical operating speed, whereas it is not true for the steering-type AGT vehicles. It is also shown that the control performance of steering-type AGT vehicles can be improved by choosing proper steering gains of the closed-loop steering control system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.785-786
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.1069-1070
• /
• 2009

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.804-810
• /
• 2004

Tilting train can pass curve at higher speed without affecting passenger comfort by tilting Carbody. But the centrifugal force proportional to square of velocity increases the track lateral force. This is the one of the problems to be solved when applying tilting train. The one countermeasure we selected the light weight design by applying distributed traction EMU system and light weight materials such as FRP. The other countermeasure was to adopt steering bogie concept in order to reduce the guiding force on Curve track. This paper describes the design study of self steering mechanism applied to the Bogie for 180 km/h Korean Tilting Train(TTX), which was done as a part of the Korean National R&D project.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.854-859
• /
• 2008

In a railway vehicle, contact between wheel and rail is a peculiar characteristic and variations of wheel and rail profile influence on the dynamic characteristics of railway vehicle. Thus the variations of the wheel and rail profile are very important in railway dynamics. Recently a research relating to active steering to improve the curving performance of vehicle is progressing actively at home and abroad. In this field, a pre-study for the wheel/rail contact geometry is needed and especially the variation of the wheel/rail contact geometry with wheel wear is the key design parameter to develop the controller of the active steering bogie. In this paper, we have experimentally studied to analyze the variation of the wheel/rail contact geometry with wheel wear as a pre-study to develop the active steering bogie for electric multiple unit (EMU). For this, we have made an experiment with EMU operating in curving area. We have measured the wear profiles of the wheel of the test vehicle and analyzed the wheel/rail contact geometry with a mileage of the test vehicle. In experiment with test vehicle, we have got the useful data to design the steering controller of the wheelset.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.265-275
• /
• 2001

This research has been performed to reveal the hysteresis phenomena of the hunting motion in a railway passenger cars. It is found that there are some factors and its operation region to make the nonlinear critical speed reacts to them more sensitively than the linear critical speed. The simulation results show that a self steering bogie system can be a substitute proposal to improve curving Performance together with the reduction of hysteresis of critical speed. Full scale roller rig test is carried out for the validation of the numerical results. Finally, it is certified that wear of wheel profile and stiffness discontinuities of wheelset suspension caused by deterioration have to be considered in the analysis to predict the hysteresis of critical speed precisely.

• 한국기계연구소 소보
• /
• s.15
• /
• pp.5-17
• /
• 1985

Dynamics of railway vehicles are strongly influenced by the wheel/rail contact forces. Wheel/rail contact geometric characteristics are important parameters to determining wheel/rail contact forces. In general, geometric relations between wheel and rail are represented by nonlinear functions of the wheelset lateral excursion and the relative yaw angle. There are some analytical and experimental studies to show the influences of the wheelset lateral displacement on wheel/rail geometric relations. Recently radial steering bogie which is designed to have flexible yaw motions of wheelsets was developed to improve curve negotiation performance. The radial steering bogie makes it important problem to study the effects of wheelset yaw motion on wheel/rail geometric relations. This paper describes the method to analyze 3-dimensional wheel/rail contact geometry considering wheelset yaw motion and describes also some computer simulation results.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.135-142
• /
• 1999

This paper deals with dynamic characteristics of automated guideway transit vehicle with rubber tires. Several models for guideway system of LRT(Light Rail Transit) have been Proposed because of the necessity of guideway system for LRT with rubber tires on exclusive rail unlike steel tires. Here, steering system and bogie system are investigated to compare with dynamic characteristics. On selecting guideway system, the way of vehicle operation should be considered and simultaneously the dynamic characteristics of the vehicle must be evaluated with respect to each guideway. The results show that stability is essential for vehicle with steering system, and that single-axle bogie system gives the good stability, though it is necessary to reduce the guide-wheel force