• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.748-757
• /
• 2007

This paper is intended to solve the technical problem that fails in large-capacity induction motor starting due to serious voltage drop during starting period. One induction motor that is established already can reach in steady-state using reactor starting method but the voltage magnitude of PCC (point of common coupling) has dropped down a little. When the same capacity induction motor is installed additionally in the PCC, where the existing induction motor is operating, voltage drop becomes more serious by starting of additional induction motor. As a result, the additional induction motor fails in starting. Therefore, voltage compensation method is proposed so that all of two induction motors can be started completely. First, modeling technique is described in order to implement starting characteristics of large induction motor. And then, this paper proposes strategic starting scheme by proper voltage compensation that use no-load transformer tap control (NLTC) and step voltage regulator (SVR) for starting of two large induction motors successfully and improving the feeding network voltage profile during the starting period. The induction motor discussed in this paper is the pumped induction motor of 2500kVA capacity that is operating by KOWACO (Korea Water Resources Corporation). Modeling and simulation is conducted using PSCAD/EMTDC software.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.12-19
• /
• 2022

Propellant grains with embedded metal wires have been used for enhancement of burning rate while maintaining high loading density. For the performance design of a solid rocket motor using propellant grain with embedded metal wires, burn-back analysis is required according to number, location, arrangement angle of metal wires, and augmentation ratio of the propellant burning rate near a wire region. In this study, a numerical method to quickly calculate a burning surface area was developed in response to the design change of the propellant grain with embedded metal wires. The burning surface area derived from the developed method was compared with the results of a CAD program. Error rate decreased as the radial size of the grid decreased. Analysis for characteristics of burning surface area was performed according to the number and location of metal wires, the initial and final phases were shortened and the steady-state phase was increased when the number of metal wires increased. When arranging the metal wires at different radii, the burning surface area rapidly increased in the initial phase and sharply decreased in the final phase compared to the case where the metal wires were disposed in the same radius.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.9C
• /
• pp.895-904
• /
• 2007

This paper proposes a robust sub-optimal smart antenna in Code Division Multiple Access (CDMA) basestation. It makes use of the property of the Least Mean Square (LMS) algorithm and the Conjugate Gradient Method (CGM) algorithm for beamforming processes. The weight update takes place at symbol level which follows the PN correlators of receiver module under the assumption that the post correlation desired signal power is far larger than the power of each of the interfering signals. The proposed algorithm is simple and has as low computational load as five times of the number of antenna elements(O(5N)) as a whole per each snapshot. The output Signal to Interference plus Noise Ratio (SINR) of the proposed smart antenna system when the weight vector reaches the steady state has been examined. It has been observed in computer simulations that proposed beamforming algorithm improves the SINR significantly compared to the single antenna case. The convergence property of the weight vector has also been investigated to show that the proposed hybrid algorithm performs better than CGM and LMS during the initial stage of the weight update iteration. The Bit Error Rate (BER) characteristics of the proposed array has also been shown as the processor input Signal to Noise Ratio (SNR) varies.

• Journal of Environmental Health Sciences
• /
• v.21 no.3
• /
• pp.38-47
• /
• 1995

The Bioconcentration factor (BCF) is used as an important criterion in the risk assessment of environmental contaminants. Also it can be used as indicator of biomagnification of environmentally hazardous chemicals through food-chain as well as a tool for ranking the bioconcentration potential of the chemicals in the environment. This paper reports the measured BCF value on Chlorothalonil in Carassius auratus(goldfish), under steady state, and examined correlation between the BCF value and the partition coefficient or acute toxicity or physicochemical properties. Carassius auratus(goldfish) was chosen as test organism and test period were 3-day, 5-day. Experimental concentrations were 0.005, 0.01 and 0.05 ppm. Chlorothalonil in fish tissue and in test water were extracted with n-hexane and acetonitrile. GC-ECD was used to detecting and quantitating of Chlorothalonil. Partition coefficient was determined by stir-flask method. $LC_{50}$ was determined on Chlorothalonil. Carbaryl and BPMC. The obtained results were as follows. 1. It was possible to determine short term BCFs of Chlorothalonil through relatively simple procedure in environmental concentrations. 2. $BF_3$ of Chlorothalonil in concentration of 0.005, 0.01 and 0.05 ppm were 2.1866$\pm$0.23446, 3.5269$\pm$0.23517, 10.2045$\pm$0.18053 and BCFs were 6.6543$\pm$0.55257, 6.9774$\pm$0.02500, 23.4576$\pm$2.06884, respectively. 3. Chlorothalonil concentration in fish extract and BCFs of Chlorothalonil were increased as increasing test concentration and prolonging test period. 4. Fate of test-water concentration on Chlorothalonil was greater than that of control-water con-centration. It is considered that greater fate of test-water concentration on Chlorothalonil is due to hydrolyzing nitrile group under the mild condition and substituting chloro group by some aromatic compounds in test water. 5. Determined logP of Chlorothalonil was 2.80. And determined $LC_{50}$ of Chlorothalonil in time of 24, 48, 72 and 96 hr were 0.1684, 0.1402, 0.1400, 0.1352(mg/l) respectively. And $LC_{50}$ of Carbaryl in above times were 19.918, 18.635, 18.466, 18.12(mg/l) respectively. $LC_{50}$ of BPMC were 10.248, 9.166, 9.087, 8.921(mg/l) respectively. 6. It is suggested that the BCF of Carbamates depend on partition coefficients. But BCF of Chlorothalonil, organochlorine pesticide, would be strongly influenced by steric, electronic effect of substituents than partition coefficient.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.1E
• /
• pp.56-64
• /
• 1995

The least mean fourth (LMF) adaptive algorithm is a stochastic gradient method that minimizes the error in the mean fourth sense. Despite its potential advantages, the algorithm is much less popular than the conventional least mean square (LMS) algorithm in practice. This seems partly because the analysis of the LMF algorithm is much more difficult than that of the LMS algorithm, and thus not much still has been known about the algorithm. In this paper, we explore the statistical convergence behavior of the LMF algorithm when the input to the adaptive filter is zero-mean, wide-sense stationary, and Gaussian. Under a system idenrification mode, a set of nonlinear evolution equations that characterizes the mean and mean-squared behavior of the algorithm is derived. A condition for the conbergence is then found, and it turns out that the conbergence of the LMF algorithm strongly depends on the choice of initial conditions. Performances of the LMF algorithm are compared with those of the LMS algorithm. It is observed that the mean convergence of the LMF algorithm is much faster than that of the LMS algorithm when the two algorithms are designed to achieve the same steady-state mean-squared estimation error.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.4
• /
• pp.372-382
• /
• 2006

Most of the conventional breakwaters impermeable breakwaters which block seawater exchange between the outside and inside of the harbors. The blocking of seawater exchange may cause pollution of water in harbors. To solve the water pollution problem, various kinds of seawater exchange breakwaters have been proposed. Their types can be classified into the current type which uses tidal current, and the overtopping type which uses the wave energy. The overtopping type breakwaters require a discharge coefficient to calculate the rate of overtopping into the harbor. The present study is to compute the rate of overtopping with introduction of a correct discharge coefficient and to evaluate the effect of the overtopping type breakwater on the water qualify inside a harbor. The rate of overtopping was computed by using Forchheimer formula with time dependent mild-slope equation for various wave conditions. The formula has been generally used to calculate the overflow discharge in steady state river flows. The discharge coefficient, which is the key parameter of the calculation, was determined by a series of hydraulic model tests. The present scheme was applied to the seawater exchange section of the western breakwater of Jeju New Harbor's and the efficiency of that section was examined. The calculated results showed that the rate of overtopping into the harbor reached about $27.5m^3/s$ in the wave condition (wave height 3.7 m, wave period 8.5s, and wave direction NNW).

• Journal of Energy Engineering
• /
• v.8 no.2
• /
• pp.224-232
• /
• 1999

Latent heat storage system using micro-encapsuled phase change material is effective method for floor heating of house and building. The temperature profile in capsule block and flow rate of hot water are important parameters for the development of heat storage system. In the present study, a mathematical model based on 3-D, non-steady state, Navier-Stokes equations, scalar conservation equations and turbulence model ($\kappa$-$\varepsilon$), is used to predict the temperature profiles in capsule and the velocity vectors in hot water pipe. The multi-block grids and fine grids embedding are used to join the circle in hot water pipe and square in capsule block. The phase change process of the capsule is quite complex not only because the size of phase change material is very small, but also because phase change material is mixed with the cement to form thermal storage block. In calculation, it's assumed that the phenomena of phase change is limited only the thermal properties of phase change material and the change of boundary is not happened in capsule. The purpose of this study is to calculate the temperature profiles in capsule block and velocity vectors in hot water pipe using the numerical calculation. Two kinds of thermal boundary condition were considered, the first (case 1) is the adiabatic condition for the both outside surfaces of the wall, the second (case 2) is the case in which one surface is natural convection with atmosphere and another surface is adaibatic. Calculation results are shown that the temperature profile in capsule block for case 1 is higher than that for case 2 due to less heat loss in adaibatic surface. Specially, in the domain of near Y=0, the difference of temperature is greater in case 1 than in case 2. The detailed experimental data of capsule block on the temperature profile and the thermal properties such as specific heat and coefficient of heat transfer with the various temperature are required to predict more exact phenomena of heat transfer.

• Fire Science and Engineering
• /
• v.16 no.1
• /
• pp.18-23
• /
• 2002

Efficiency estimation of toxicity free resistance cable experiments were conducts to understand toxicity free fire ersistance polyolefin insulation material and smoke density characteristic and combustion gas corrosion analysis. A main cause of fire-growth and generating toxic gas when it burns, should be dealt with great care in life safety design. Similar patterned fire incidents such as, Inchon Live-Hof Pub Restaurant as, Sea-land Children Resort have proven that serious loss of lives were caused by hazardous gas generated fire resistance cable materials. In this paper, Referenced documents were ASTM E662 standard test method for specific Ds genalated by solid materials. The furnace control system shall maintain the required irradiance level under steady-state condition with the chamber door closed of 2.5$\pm40.04〔w/$\textrm{cm}^2$〕for 20 min. According to the results of the smoke density analysis of NFR-8 and FR-PVC the highest decomposition flaming smoke density range of NFR-8 and FR-PVC were 25.2 to 37.5 and 51.1 respectively. Nonflaming smoke density range of NFR-8 and FR-PVC were 100.4 to 112.2 and 126.5 to 398.8. Also, the fire gases was occurred carbon monoxide and decomposition than in polyolefin due to incomplete combustion of PVC which has high content of carbon in chemical compound.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6432-6439
• /
• 2014

The NAUT (Non-contact Air coupled Ultrasonic Testing) technique is one of the ultrasonic testing methods that enables non-contact ultrasonic testing by compensating for the energy loss caused by the difference in acoustic impedance of air with an ultrasonic pulser receiver, PRE-AMP and high-sensitivity transducer. As the NAUT is performed in a state of steady ultrasonic transmission and reception, testing can be performed on materials of high or low temperatures or specimens with a rough surface or narrow part, which could not have been tested using the conventional contact-type testing technique. For this study, the internal defects of spot weld, which are often applied to auto parts, and CFRP parts, were tested to determine if it is practical to make the NAUT technique commercial. As the spot welded part had a high ultrasonic transmissivity, the result was shown as red. On the other hand, the part with an internal defect had a layer of air and low transmissivity, which was shown as blue. In addition, depending on the PRF (Pulse Repetition Frequency), an important factor that determines the measurement speed, the color sharpness showed differences. With the images obtained from CFRP specimens or an imaging device, it was possible to identify the shape, size and position of the internal defect within a short period of time. In this paper, it was confirmed in the above-described experiment that both internal defect detection and image processing of the defect could be possible using the NAUT technique. Moreover, it was possible to apply NAUT to the detection of internal defects in the spot welded parts or in CFRP parts, and commercialize its practical application to various fields.

• Tribology and Lubricants
• /
• v.36 no.2
• /
• pp.105-115
• /
• 2020

This paper presents a numerical study on the rotordynamic analysis of a dual-spool turbofan engine in the context of blade defect events. The blades of an axial-type aeroengine are typically well aligned during the compressor and turbine stages. However, they are sometimes exposed to damage, partially or entirely, for several operational reasons, such as cracks due to foreign objects, burns from the combustion gas, and corrosion due to oxygen in the air. Herein, we designed a dual-spool rotor using the commercial 3D modeling software CATIA to simulate blade defects in the turbofan engine. We utilized the rotordynamic parameters to create two finite element Euler-Bernoulli beam models connected by means of an inter-rotor bearing. We then applied the unbalanced forces induced by the mass eccentricities of the blades to the following selected scenarios: 1) fully balanced, 2) crack in the low-pressure compressor (LPC) and high pressure compressor (HPC), 3) burn on the high-pressure turbine (HPT) and low pressure compressor, 4) corrosion of the LPC, and 5) corrosion of the HPC. Additionally, we obtained the transient and steady-state responses of the overall rotor nodes using the Runge-Kutta numerical integration method, and employed model reduction techniques such as component mode synthesis to enhance the computational efficiency of the process. The simulation results indicate that the high-vibration status of the rotor commences beyond 10,000 rpm, which is identified as the first critical speed of the lower speed rotor. Moreover, we monitored the unbalanced stages near the inter-rotor bearing, which prominently influences the overall rotordynamic status, and the corrosion of the HPC to prevent further instability. The high-speed range operation (>13,000 rpm) coupled with HPC/HPT blade defects possibly presents a rotor-case contact problem that can lead to catastrophic failure.