• Ocean Systems Engineering
• /
• 제7권3호
• /
• pp.179-193
• /
• 2017

Dynamic response analysis of offshore triceratops with stiffened buoyant legs under impact and non-impact waves is presented. Triceratops is relatively new-generation complaint platform being explored in the recent past for its suitability in ultra-deep waters. Buoyant legs support the deck through ball joints, which partially isolate the deck by not transferring rotation from legs to the deck. Buoyant legs are interconnected using equally spaced stiffeners, inducing more integral action in dispersing the encountered wave loads. Two typical nonlinear waves under very high sea state are used to simulate impact and non-impact waves. Parameters of JONSWAP spectrum are chosen to produce waves with high vertical and horizontal asymmetries. Impact waves are simulated by steep, front asymmetric waves while non-impact waves are simulated using Stokes nonlinear irregular waves. Based on the numerical analyses presented, it is seen that the platform experiences both steady state (springing) and transient response (ringing) of high amplitudes. Response of the deck shows significant reduction in rotational degrees-of-freedom due to isolation offered by ball joints. Weak-asymmetric waves, resulting in non-impact waves cause steady state response. Beat phenomenon is noticed in almost all degrees-of-freedom but values in sway, roll and yaw are considerably low as angle of incidence is zero degrees. Impact waves cause response in higher frequencies; bursting nature of pitch response is a clear manifestation of the effect of impact waves on buoyant legs. Non-impact waves cause response similar to that of a beating phenomenon in all active degrees-of-freedom, which otherwise would not be present under normal loading. Power spectral density plots show energy content of response for a wide bandwidth of frequencies, indicating an alarming behaviour apart from being highly nonlinear. Heave, being one of the stiff degrees-of-freedom is triggered under non-impact waves, which resulted in tether tension variation under non-impact waves as well. Reduced deck response aids functional requirements of triceratops even under impact and non-impact waves. Stiffened group of buoyant legs enable a monolithic behaviour, enhancing stiffness in vertical plane.

• Journal of the Institute of Convergence Signal Processing
• /
• 제17권2호
• /
• pp.77-82
• /
• 2016

The purpose of this paper is to develop the algorithm of human arousal inducing interface using steady-state visual evoked potential(SSVEP) and its verification through experiments. In order to develop the model, computer-based SSVEP program simulation is preliminary performed. From the results of the simulation, stimulus pattern is decided to checkerboard and SSVEP frequency range is set into beta wave (13~30Hz). After the experiment on proving the effect of SSVEP flashing stimulation while driving by installing it at the location of people mostly falling asleep in the highway, the result confirms that both during the night and the day, after SSVEP flashing stimulation, a wave Beta immediately increases and the subjects keep high stimulation for the 5 minute maintaining stage.

• Journal of Ocean Engineering and Technology
• /
• 제31권3호
• /
• pp.202-207
• /
• 2017

This paper presents the results of an experimental study on the motions and mooring characteristics of a floating vertical axis wind turbine system. Based on a comparison of regular wave experiment results, the motions of structures with different types of mooring are almost the same. Based on the tension response results of a regular wave experiment with a catenary mooring system, the mooring lines in front of the structure have a larger tension effect than the back of the structure by the drifted offset of the structure. The dynamic response spectrum of the structure in the irregular wave experiments showed no significant differences in response to differences in the mooring system. As a result of the comparison of the tension response spectra, the mooring lines have a larger value with a drifted offset for the structure, as shown in the previous regular wave experiment. The results of the dynamic response of the structure under irregular wave and wind conditions showed that the heave motion response is influenced by the coupled effect with the mooring lines of the surge and pitch motion due to the drifted offset and steady heeling. In addition, the mooring lines in front of the structure have a very large tension force compared to the mooring lines in back of the structure as a result of the drifted offset of the structure.

• Journal of the Korean Applied Science and Technology
• /
• 제26권2호
• /
• pp.103-109
• /
• 2009

Chemicals for cosmetics, including skin, the skin absorbs some of the research in the field of science or pharmacy recently, about the environment and the health of the heightened interest in skin absorption. Many other human attributes and absorption evaluation studies are underway in various areas. This study were used rats and carried out to find out the effects of commercial permanent wave products to skin which are composed with thioglycolic acid and bases. Results were as follows. Permanent wave penetrated to 3 hours later with steady state in skins and was not significant changeable after 20hr later. In case of neutralizer with thioglycolic acid lag time and permeability coefficient in healthy skin were 3.32hr and $0.101{\mu}g/cm^2/hr$, in old skin were 3.08hr and $0.117{\mu}g/cm^2/hr$, and in wounded skin were 3.02hr and $0.166{\mu}g/cm^2/hr$. In conclusion, lag time and permeability coefficient in old skin and wounded skin were faster than healthy skin. In vivo, We were studied to general time and method of permanent wave. We found out that fine wrinkle and rash of skin were changeable in the case of treating with permanent wave drugs than normal skin.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제33권7호
• /
• pp.18-25
• /
• 2005

In this study, the main focus is the simulation of acoustic wave scattering in trailing edge and the analysis of the generation mechanism of instability wave by the interaction of trailing edge, shear flow and initial disturbance. The numerical algorithm is based on CFD/CAA hybrid method with high-order computational aeroacoustic method. It is found that steady mean flow gradient terms play a crucial role on the generation of instability wave through the comparison of simulations of Simple Linearized Euler Equation and Full Linearized Euler Equation. Through the comparison with the results of Full Navier-Stokes Equation, it is reasonable and efficient to use the Full Linearized Euler Equation in the initial generation mechanism of the instability wave near the trailing edge.

• Computers and Concrete
• /
• 제33권4호
• /
• pp.399-407
• /
• 2024

This study nondestructively examined the evolution of crack density in ultra-high performance concrete (UHPC) upon cyclic loading. Uniaxial compression was repeatedly applied to the cylindrical specimens at levels corresponding to 32% and 53% of the maximum load-bearing capacity, each at a steady strain rate. At each stage, both P-wave and S-wave velocities were measured in the absence of the applied load. In particular, the continuous monitoring of P-wave velocity from the first loading prior to the second loading allowed real-time observation of the strengthening effect during loading and the recovery effect afterwards. Increasing the number of cycles resulted in the reduction of both elastic wave velocities and Young's modulus, along with a slight rise in Poisson's ratio in both tested cases. The computed crack density showed a monotonically increasing trend with repeated loading, more significant at 53% than at 32% loading. Furthermore, the spatial distribution of the crack density along the height was achieved, validating the directional dependency of microcracking development. This study demonstrated the capability of the crack density to capture the evolution of microcracks in UHPC under cyclic loading condition, as an early-stage damage indicator.

• Journal of Environmental Science International
• /
• 제20권6호
• /
• pp.783-788
• /
• 2011

Different from the main land of South Korea, Jeju Island has been in difficulties for measuring discharge. Due to high infiltration rate, most of streams in Jeju Island are usually in the dried state except six streams with the steady base flow, and the unique geological characteristics such as steep slope and short traveling distance of runoff have forced rainfall runoff usually to occur during very short period of time like one or two days. While discharge observations in Jeju Island have been conducted only for 16 sites with fixed electromagnetic surface velocimetry, effective analysis and validation of observed discharge data and operation of the monitoring sites still have been limited due to very few professions to maintain such jobs. This research is sponsored by Ministry of Land, Transport and Maritime Affairs to build water cycle monitoring and management system of Jeju Island. Specifically, the research focuses on optimizing discharge measurement techniques adjusted for Jeju Island, expanding the monitoring sites, and validating the existing discharge data. First of all, we attempted to conduct discharge measurements in streams with steady base flow, by utilizing various recent discharge monitoring techniques, such as ADCP, LSPIV, Magnetic Velocimetry, and Electromagnetic Wave Surface Velocimetry. ADCP has been known to be the most accurate in terms of discharge measurement compared with other techniques, thus that the discharge measurement taken by ADCP could be used as a benchmark data for validation of others. However, there are still concerns of using ADCP in flood seasons; thereby LSPIV would be able to be applied for replacing ADCP in such flooded situation in the stream. In addition, sort of practical approaches such as Magnetic Velocimetry, and Electromagnetic Wave Surface Velocimetry would also be validated, which usually measure velocity in the designated parts of stream and assume the measured velocity to be representative for whole cross-section or profile at any specified location. The result of the comparison and analysis will be used for correcting existing discharge measurement by Electromagnetic Wave Surface Velocimetry and finding the most optimized discharge techniques in the future.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 한국항해항만학회 2006년도 추계학술대회 논문집(제1권)
• /
• pp.57-62
• /
• 2006

Busan New Port, under construction aiming for the hub of Northeast Asia and Partly in operation, had damaged up to 48 billion Won due to Typhoon 'maemi' in 2003. The present criteria of domestic harbor design only describes about the critical wave height with respect to the size of vessel for harbor tranquility. The berth operation ratio which represents the annual available berthing days is depending on the efficiency of cargo handling work and this depends on the motion of the moored vessel due to the wave action and the characteristics of cargo gears. The motion of moored vessel might be related not only to the wave height but also to wave period. Furthermore, the berth operation ratio relies on external forces such as currents and winds, including the characteristics of mooring system and the specification of the moored vessel. In this study we only deal with berth operation ratio in normal sea state, considering wave and current by measured data and numerical calculation. Especially we tried to evaluate the berth operation ratio for each berth adopting the variation of dredging and reclamation plan and the change of wave environment during the process of the new port construction. For better understanding and analysis of wave transformation process, we applied the steady state spectral wave model and extended mild-slope wave model to the related site. This study summarizes comparisons of harbor responses predicted by two numerical predictions obtained at Busan New port site. Field and numerical model analysis was conducted for the original port plan and the final corrected plan.

• Journal of the Society of Naval Architects of Korea
• /
• 제47권3호
• /
• pp.377-387
• /
• 2010

In this study, the turbulent free surface around KVLCC1 employed in the circular motion test simulation is numerically calculated using a commercial CFD(Computational Fluid Dynamics) code, FLUENT. Also, hydrodynamic forces and yaw moments around a ship model are calculated during the steady turning. Numerical simulations of the turbulent flows with free surface around KVLCC1 have been carried out by use of RANS equation based on calculation of hydrodynamic forces and yaw moments exerted upon the ship hull. Wave elevation is simulated by using the VOF method. VOF method is known as one of the most effective numerical techniques handling two-fluid domains of different density simultaneously. Boundary layer thickness and wake field are changed various yaw velocities of ship model during the steady turning. The calculated hydrodynamic forces are compared with those obtained by model tests.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1816-1821
• /
• 2001

Two-dimensional blow-down type supersonic wind tunnel was designed and built to investigate the transient behavior of the startup of a supersonic flow from rest. The contour of the divergent part of the nozzle was determined by the MOC calculation. The converging part of the nozzle, upstream of fille throat was contoured to make the flow uniform at the throat. The flow characteristics of the steady supersonic condition were visualized using the high-speed schlieren photography. The Mach number was evaluated from the oblique shock wave angle on a sharp wedge with halt angle of 5 degree. The measured Mach number was 2.4 and was slightly less than the value predicted by the design calculation. The initial transient behavior of the nozzle was recorded by a high-speed digital video camera with schlieren technique. The measured transition time from standstill to a steady supersonic flow was estimated by analyzing the serial images. Typical transition time was approximately 0.1sec.