• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1384-1387
• /
• 2003

Pressurization test is usually required in aircraft full-scale static test. There are several test conditions including pressurization of cockpit, fuselage fuel tank, air inlet duct for T-50 full-scale static test. In this paper, the test conditions, equipment, piping analysis for the pressurization test are introduced. Tank simulation test is performed to verify the validity of piping analysis and to find good tuning parameters for the pressurization channel in the servo controller. Several test setup for pressurization of T-50 test is introduced. Test article volume is filled by form, $60%{\sim}80%$ volume is reduced for the T-50 full-scale static test. Pressurization system is connected to servo controller which also controls hydraulic actuator. Load and pressure control is synchronized by using the same servo controller during T-50 test. Typical control result for pressurization test condition is shown. Pressurization tests of T-50 full-scale static test was completed successfully.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.904-911
• /
• 2001

The fuels of water-in-oil emulsion have a potential of reducing PM(Particulate Matter) and NOx emissions, and increasing combustion efficiency in the furnaces and the burners. For making the most of the beneficial of the secondary atomization due to the microexplosion, the water droplets distributed in the oil must have the optimal sizes. The purpose of this paper is to investigate the water droplet size distribution characteristics of the different types of the static mixers. For analysis the size distribution characteristics efficiently, image analysis system wes constructed and an appropriate image processing algorithm was developed. Two kinds of static mixers: Kenics type and RF type, were tested. As a results, RF type static mixer shows a better characteristics in the mean drop size, particularly in the condition of high water content.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.5
• /
• pp.845-848
• /
• 1994

The fermenting conditions for acetic acid production with Acetobacter sp. FM-10 which could grow in the medium containing 10% ehtanol were investigated. Initial concentration of acetic acid in broth medium affected greatly to the fermentation speed. For example , the acetic acid production increased proportionally by the increasing of initial concentration was higher that 1.0%. When the cultivation was started with broth medium containing 5% ethanol, the additional adding ethanol during the fermentation was not significantly increased the acidity of the medium. The acidity of the medium containing 10% ethanol was reached to 8.3% after shaking than static cultivation by about 10 days with 150 rpm shaking speed. Acetic acid production with shaking cultivation was faster the static cultivation by abot 10 days under the same condition except shaking. In acetic acid fermentation with the batch style fermentor , the optimum fermentation condition was 700 rpm of agitation speed and 5L/min air flow rate in 3L culture medium .

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.877-880
• /
• 1999

A rigorous formulation is suggested〔l,2,3〕 in solving the scattering of plane waves by a dielectric wedge. Correcting surface currents are expanded in a Neumann series of fractional orders to meet the edge condition of static limit〔4〕. For the better converging series, the modified Neumann series satisfying the static limit edge condition and the radiation condition are suggested here for the surface currents having two different wave numbers of air and dielectric〔4〕. This representation gives accurate solutions over the whole region including the grazing incidence of the plane waves upon the dielectric wedge of large permittivities.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.66-71
• /
• 2010

This paper studies the effect of saturation of backfill on the seismic stability of reinforced soil walls (RSWs) using centrifuge shaking table tests. For comparison, degradation of static stability and seismic stability of a RSW under unsaturated condition was also investigated. Test results showed that the RSW under saturated condition had enough static stability. However, seismic stability of saturated RSW significantly decreased as compared with that under unsaturated condition. The saturated model RSW did not collapse, though it showed large deformation. It maintained sufficient stability after shakings although a clear slip surface appeared in the backfill. Finally, it is discussed how to evaluate residual stability of RSWs damaged by earthquakes with test results and the simple evaluation method proposed by authors.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.2
• /
• pp.207-207
• /
• 1991

The crack length measurements by electrical potential(EP) method for 1% Cr-Mo-V and 12%Cr steel of 0.5T-CT specimen were performed at $500^{\circ}C, 600^{\circ}C 700^{\circ}C$, and an applicability of stress intensity factor($K_I$), net section stress($\sigma_{net}$), $C^*$-ingegral and $C_t$ parameter was studied to measure creep crack growth rate(da/dt) with side groove and without side groove under static and cyclic loading condition. The experimental result could be summarized as follows: 1) Crack measurement by EP method was available and coincided with the Johnson,s analytical equation. 2) da/dt by $K_I$ and $\sigma_{net}$ was not adequate because of the wide scatter band according to load and temperature, but $C^*$-integral, except for transition region, was adequate. 3) $C_t$ parameter showed the best fitted line through total creep region without relating with both temperature and load condition. 4) Under the cyclic loading condition, $C_t$ parameter was proper to extimate da/dt. And it was shown that da/dt for 1% Cr-Mo V steel under the static condition(R=1) was 1.16 times faster than the case under cyclic loading(R=0), and for 12% Cr steel, 1.43 times.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.2
• /
• pp.67-75
• /
• 1991

The crack length measurements by electrical potential(EP) method for 1% Cr-Mo-V and 12%Cr steel of 0.5T-CT specimen were performed at $500^{\circ}C, 600^{\circ}C 700^{\circ}C$, and an applicability of stress intensity factor($K_I$), net section stress($\sigma_{net}$), $C^*$-ingegral and $C_t$ parameter was studied to measure creep crack growth rate(da/dt) with side groove and without side groove under static and cyclic loading condition. The experimental result could be summarized as follows: 1) Crack measurement by EP method was available and coincided with the Johnson, s analytical equation. 2) da/dt by $K_I$ and $\sigma_{net}$ was not adequate because of the wide scatter band according to load and temperature, but $C^*$-integral, except for transition region, was adequate. 3) $C_t$ parameter showed the best fitted line through total creep region without relating with both temperature and load condition. 4) Under the cyclic loading condition, $C_t$ parameter was proper to extimate da/dt. And it was shown that da/dt for 1% Cr-Mo V steel under the static condition(R=1) was 1.16 times faster than the case under cyclic loading(R=0), and for 12% Cr steel, 1.43 times.

• Physical Therapy Korea
• /
• v.8 no.3
• /
• pp.1-10
• /
• 2001

The purpose of this study was to compare the static pressure, dynamic pressure, dynamic pressure-time integral, relative impulse, and contact time between the sound lower limb and amputated lower limb in trans-tibial amputee subjects using Parotec system. Seventeen trans-tibial amputee subjects wearing endoskeletal trans-tibial prosthesis voluntarily participated in this study. The results were as follows: 1) In static standing condition, there were significantly higher static pressure in sound lower limb insole sensor of 10, 14, 15, 18, 19, 23, and 24 and in amputated lower limb insole sensor of 9, 12, and 16 (p<.05). 2) In dynamic gait condition, there were significantly higher dynamic pressure in sound lower limb insole sensor of 2, 18, 22, 23, and 24 and in amputated lower limb insole sensor of 5, 9, 10, 11, 12, 14, 15, and 16 (p<.05). 3) In dynamic gait condition, there were significantly higher pressure-time integral in sound lower limb insole sensor of 2, 4, 18, 19, 20, 21, 23, and 24 and in amputated lower limb insole sensor of 5, 11, 12, and 15 (p<.05). 4) In dynamic gait condition, there were significantly higher relative impulse in sound lower limb insole sensor of 18, 19, 20, 22, 23, and 24 and in amputated lower limb insole sensor of 5, 9, 10, 11, 12, and 15 (p<.05). 5) In dynamic gait condition, there was significantly higher percentage of contact time in push off phase of sound lower limb and in support phase of amputated lower limb (p<.05). These results suggest that trans-tibial amputee subjects had characteristics of shortened push off phase due to unutilized forefoot and of lengthened support phase with higher pressure in the midfoot.

• Atmosphere
• /
• v.33 no.4
• /
• pp.331-341
• /
• 2023

A numerical forecasting models usually predict future states by performing time integration considering fixed static time-steps. A time-step that is too long can cause model instability and failure of forecast simulation, and a time-step that is too short can cause unnecessary time integration calculations. Thus, in numerical models, the time-step size can be determined by the CFL (Courant-Friedrichs-Lewy)-condition, and this condition acts as a necessary condition for finding a numerical solution. A static time-step is defined as using the same fixed time-step for time integration. On the other hand, applying a different time-step for each integration while guaranteeing the stability of the solution in time advancement is called an adaptive time-step. The adaptive time-step algorithm is a method of presenting the maximum usable time-step suitable for each integration based on the CFL-condition for the adaptive time-step. In this paper, the adaptive time-step algorithm is applied for the Korean Integrated Model (KIM) to determine suitable parameters used for the adaptive time-step algorithm through the monthly verifications of 10-day simulations (during January and July 2017) at about 12 km resolution. By comparing the numerical results obtained by applying the 25 second static time-step to KIM in Supercomputer 5 (Nurion), it shows similar results in terms of forecast quality, presents the maximum available time-step for each integration, and improves the calculation efficiency by reducing the number of total time integrations by 19%.

• Physical Therapy Korea
• /
• v.28 no.3
• /
• pp.200-207
• /
• 2021

Background: Postural control deficit is a major characteristic in patients with chronic ankle instability (CAI). Elastic ankle tapings are commonly used to facilitate postural control in patients with CAI as well as prevent relapse of a lateral ankle sprain. However, equivocal evidence exists concerning the effect of elastic ankle taping on postural control. Objects: This study aimed to evaluate the effects of elastic ankle tapings using kinesio taping (KT) and dynamic taping (DT) on static and dynamic postural control in patients with CAI. Methods: Fifteen subjects with CAI were participated in this study. The participants performed tests under three conditions (barefoot, KT, and DT). Static postural control was evaluated using the one-leg standing test (OLST) and dynamic postural control using the modified Star Excursion Balance Test (mSEBT). One-way repeated-measures analysis of variance was used to compare center of pressure (CoP) data and normalized mSEBT reach distances among the three conditions (with α = 0.05). Results: The CoP parameters (path length, ellipse area, and mean velocity) of the OLST significantly decreased on applying KT and DT compared with those when barefoot. The normalized reach distances in the anteromedial (AM), medial (M), and posteromedial (PM) directions of the mSEBT significantly increased with DT compared to that in the control condition. Further, the higher reach distances with KT compared with those in the control condition were obtained in the M and PM directions of the mSEBT. No significant differences were identified in any of the OLST and SEBT parameters between the two different taping applications. Conclusion: KT and DT improved static postural control during the OLST compared with the control condition. Moreover, these tapes improved dynamic postural control during the mSEBT compared to the control. Therefore, elastic ankle tapings are useful prophylactic devices for the prevention and treatment of ankle sprain in people with CAI.