• 한국해양학회지
• /
• 제1권1_2호
• /
• pp.1-6
• /
• 1966

A latitudinal, differential pH distribution is observed in the Northeastern Pacific Ocean with a pH range of 8.15 at high latitude (42 N) to 8.29 at low latitude (23 N). These pH values are generally greater than the calculated equilibrium pH with respect to atmospheric carbon dioxide. If we assume that the calculated equilibrium pH values ae valid, then the surface waters are undersaturated with respect to the atmospheric carbon dioxide during April to June 1966. A high surface pH value of about 8.26 was observed immediately south of the SubarcticBoundary zone near 170 W. This value differs from the equilibration pH by as much as 0.1 unit.

• Wind and Structures
• /
• 제5권2_3_4호
• /
• pp.347-358
• /
• 2002

Mean surface pressures and overall wind loads on hemispherical domes immersed in a boundary layer were obtained by numerical simulation. The effects of alternative turbulence models, Reynolds Number and surface roughness were examined and compared with earlier studies. Surface pressures on dual hemispherical domes were also calculated for three wind orientations ($0^{\circ}$, $45^{\circ}$, and $90^{\circ}$) to evaluate flow field interactions. Calculated values were compared to wind-tunnel measurements made in equivalent flow conditions.

• 한국환경과학회지
• /
• 제5권6호
• /
• pp.727-738
• /
• 1996

An one dimensional atmosphere-canopy-soil interaction model is developed to estimate of the heat budget parameter in the atmospheric boundary layer. The canopy model is composed of the three balance equations of energy, temperature, moisture at ground surface and canopy layer with three independent variables of Tf(foliage temperature), Tg(ground temperature), and qg(ground specific humidity). The model was verilied by comparative study with OSUID(Oregon State University One Dimensional Model) proved in HAPEX-MOBILHY experiment. Also we applied this model in two dimensional land-sea breeze circulation. According to the results of this study, surface characteristics considering canopy acted importantly upon the simulation of meso-scale circulation. The factors which used in the numerical experiment are as follows ; the change for a sort of soil(sand and peat), the change for shielding factor, and the change for a kind of vegetation.

• 한국해양공학회지
• /
• 제15권1호
• /
• pp.1-6
• /
• 2001

This study focuses on the potential flow analysis for a hull with the transom stern. The method is based on a low order panel method. The Kelvin type free-surface boundary condition which is known to better fit experimental data for a high speed is applied. To treat a dry transom stern effect a special treatment for the free-surface boundary condition is adopted at the free-surface region after the transom stern. Trim and sinkage, which are important in high speed ships, are considered by an iterative method. Pressure and momentum approaches are used to calculate the wave resistance. Numerical calculations are performed for Athena hull and these results are compared with the experimental data and also other computational results.

• Wind and Structures
• /
• 제4권4호
• /
• pp.279-298
• /
• 2001

The greatest suction on the cladding of flat roof low-rise buildings is known to occur beneath the conical vortices that form along the roof edges for cornering winds. In a companion paper, a model of the vortex flow mechanism has been developed which can be used to connect the surface pressure beneath the vortex to adjacent flow conditions. The flow model is experimentally validated in this paper using simultaneous velocity and surface pressure measurement on a 1 : 50 model of the Texas Tech University experimental building in a wind tunnel simulated atmospheric boundary layer. Flow visualization gives further insight into the nature of peak suction events. The flow model is shown to account for the increase in suction towards the roof corner as well as the presence of the highest suction at wind angles of $60^{\circ}$. It includes a parameter describing vortex suction strength, which is shown to be related to the nature of the reattachment, and also suggests how different components of upstream turbulence could influence the surface pressure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.634-639
• /
• 2003

It has been studied the flow near a rotating disk with surface topography. The system Ekman number is assumed very small, i.e., $E[{\equiv}\frac{\nu}{{\Omega}^{\ast}L^{\ast2}}]<<1$ in which $L^{\ast}$ denotes a disk radius, ${\nu}$ kinematic viscosity of the fluid and ${\Omega}^{\ast}$ angular velocity of the basic state. Disk surface has a sinusoidal topographic variation along radial coordinate, i.e., $z={\delta}cos(2{\pi}{\omega}r)$, where ${\delta}$ and ${\omega}$ are, respectively, nondimensional amplitude and wave number of the disk surface. Analytic solutions, being useful over the parametric ranges of ${\delta}{\sim}O$( $E^{1/2}$ ) and ${\omega}{\leq}O$ ( $E^{1/2}$ ), are secured in a series-function form of Fourier-Bessel type. An asymptotic behavior, when $E{\rightarrow}0$, is clarified as : for a disk with surface roughness, in contrast to the case of a flat disk, the azimuthal velocity increases in magnitude, together with the thickening boundary layer. The radial velocity, however, decreases in magnitude as the amplitude of surface waviness increases. Consequently, the overall Ekman pumping at the edge of the boundary layer remains unchanged, maintaining the constant value equal to that of the flat disk.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1810-1815
• /
• 2003

Sliding mode control with nonlinear interpolation in the boundary layer is proposed. A modified sigmoid function is used for nonlinear interpolation in the boundary layer and its parameter is tuned by a fuzzy logic controller. The fuzzy logic controller that takes the distance between the system state and the sliding surface as its input guides the choice of parameter of the modified sigmoid function and the parameter is on-line tuned. Owing to the decreased thickness, the proposed method has better tracking performance than the conventional linear interpolation method. To demonstrate its performance, the proposed control algorithm is applied to a simple nonlinear system model.

• 지적과 국토정보
• /
• 제46권2호
• /
• pp.93-105
• /
• 2016

현행법상 28개 지목 중에서 가장 빈번하게 신설 또는 변경되는 지목은 '도로'이다. 타 지목에서와 마찬가지로, 도로의 경계는 관련 설정원칙과 법에 따라 엄격히 확정되고 있다. 그런데 이러한 경계설정기준 중 일부, 즉 지형지물을 이용한 경계설정의 원칙과 법규해석이 혼동되는 경우가 있는데, 이는 주로 도시계획 등 토지이용계획을 구상하는 단계에서 발생한다. 법적규정은 법의 제정취지가 중요한 데, 경계확정 규정의 제정취지를 잘 못 유권 해석함으로 인해 도로경계는 현실상황과 괴리되는 문제점을 발생시킨다. 이를 시급히 보완키 위해 일부 규정의 개정, 보완이 필수적이다. 법률용어인 '절토면'과 '경사면'의 적용이 통일되어야 하고, '구조물'이라는 용어는 '지형 지물'로 개선할 것을 제언한다.

• International Journal of CAD/CAM
• /
• 제9권1호
• /
• pp.103-109
• /
• 2010

Recently, various conformal geometric methods have been presented for non-rigid surface matching and registration. This work proposes to improve the robustness of conformal geometric methods to the boundaries by incorporating the symmetric information of the input surface. We presented two symmetric conformal mapping methods, which are based on solving Riemann-Cauchy equation and curvature flow respectively. Experimental results on geometric data acquired from real life demonstrate that the symmetric conformal mapping is insensitive to the boundary occlusions. The method outperforms all the others in terms of robustness. The method has the potential to be generalized to high genus surfaces using hyperbolic curvature flow.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 D
• /
• pp.2661-2663
• /
• 2000

In general, to reduce chattering in sliding mode control, a boundary layer around the sliding surface is used, and a continuous control is applied within the boundary. In this paper we propose the design method of sliding mode controller with sliding sector. To do this, the variable structure controller is designed for the linear system with uncertainty using sliding sector. The control law designed in the paper transfers the system state from outside to the inside of the sliding sector and ensures that some norm of the system state keeps decreasing.