• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.258-263
• /
• 2002

A numerical analysis using 2-D unsteady compressible program is conducted to explain characteristics of rotating stall such as rotating speed and number of stall cells in an one-stage axial compressor. Unlike an axial compressor which has only a rotor, in one-stage axial compressor a rotating stall is generated by rotor/stator interaction and tack pressure rising without any artificial disturbance and modeling. As a back pressure is raised, the separation of suction side at blades is increased uniformly, but because of the discrepancy of blockage effect by stator, the disturbances are generated to form a stall cell. Once the stall cell is formed, regularly the stall cell are rotating through rotor blades. When the speed of rotor is design speed the rotating speed of stall cell is $83.3\%$ of rotor rotating speed. When the speed of rotor is $80\%$ of design speed, the speed of rotating stall is $88.2\%$ of rotor speed. The number of generated stall cell are also varied for rotor speed and back pressure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.9 s.240
• /
• pp.971-978
• /
• 2005

Effects of inlet distorted flow on performance, stall and surge are experimentally investigated for a high-speed centrifugal compressor. Tested results for the distorted inlet flow cases are compared with the result of the undistorted one. The performance of compressor is slightly deteriorated due to the inlet distortion. The inlet distortion does not affect the number of stall cell and the propagation velocity. It also does not change stall inception flow rate. However, as the distortion increases, stall starts at the higher flow rate for low speed and at the lower flow rate for high speed. For 50,000 rpm stall occurrs as the flow rate decreases, however disappears fur the smaller flow rate. This is due to the interaction of surge and stall. After the stall and surge interact, the number of stall cell decreases.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1247-1254
• /
• 1998

The vaneless diffusers are widely used in industrial centrifugal compressors which are required to operate within a wide flow range. When very high pressure gases are handled by centrifugal compressor. rotating stall is a serious problem because of the occurance of large aerodynamic exciting forces. Rotating stall mostly often occurs in the impellers but it can occur in vaneless diffusers as well. In this experimental study, the rotating stall in vaneless diffuser with radial type centrifugal impeller was measured by changing the flow rate with I-type, X-type hotwire. As the result, it was cleared which type of rotating stall of the impeller stall would occur and how many stall cells would appear relating with the flow rate. As the flow rate reduced, the propagation speed of rotating stall was reduced. But the stall cell number unchanged with respect to the flow rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.2
• /
• pp.153-161
• /
• 1998

This study describes the results of the analysis of measured rotating stall signal in a centrifugal compressor with vaneless diffuser. Unsteady flow and rotating stall in vaneless diffuser were investigated by measuring of unsteady velocity fluctuation using hot-wire anemometer. Experiments were carried out in several impeller rotating speeds, at different radius ratios. Single hot -wire was used to study the characteristics of rotating stall. As a result, the abrupt rotating stall was detected at all measured impeller rotating speeds and the several flow coefficients which are less than 0.16. The number of the stall cell was one at all measured rotational speeds, and the rotating direction was the same as that of the impeller. As the flow rate decreased, the profile of the phase averaged radial velocity component with time changed from a sawtooth to a sine wave.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.476-481
• /
• 2003

In this paper, the effect of circumferential inlet distortion on performance and stall has been experimentally investigated in a high-speed centrifugal compressor, comparing distorted cases with undistorted one. The performance of compressor was slightly deteriorated by defect of inlet static pressure which is caused by the circumferential inlet distortion. As stall was fully developed the inlet distortion did not affect the number of stall cell and the propagation velocity. It also did not affect stall inception at 40,000 and 50,000 rpm. However stall occurred at the lower flow rate for distorted flow at 60,000 rpm. For 50,000 rpm a unexpected phenomenon occurred : stall occurred first and then it disappeared.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.179-186
• /
• 1999

Three-dimensional flow analysis is implemented to investigate the flow through transonic axial-flow compressor rotor(NASA R67), and to evaluate the performances of k-$\epsilon$ and Baldwin-Lomax turbulence models. A finite volume method is used for spatial discretization. And, the equations are solved implicitly in time with the use of approximate factorization. Upwind difference scheme is used for inviscid terms, but viscous terms are centrally differenced. The flux-difference-splitting of Roe is used to obtain fluxes at the cell faces. Numerical analysis is performed near peak efficiency and near stall. And, the results are compared with the experimental data for NASA R67 rotor. Blade-to-Blade Mach number distributions are compared to confirm the accuracy of the code. From the results, we conclude that k-$\epsilon$ model is better for the calculation of flow rate and efficiency than Baldwin-Lomax model. But, the predictions for Mach number and shock structure are almost same.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1384-1391
• /
• 2001

Three-dimensional flow analysis is implemented to investigate the flow through transonic axial-flow compressor rotor(NASA R67) and to evaluate the performances of Abid's low-Reynolds-number k-$\omega$ and Baldwin-Lomax turbulence models. A finite volume method is used fur spatial discretization. The equations are solved implicitly in time by the use of approximate factorization. The upwind difference scheme is used for inviscid terms and viscous terms are approximated with central difference. The flux-difference-splitting method of Roe is used to obtain fluxes at the cell faces. Numerical analysis is performed near peak efficiency and near stall. The results are compared with the experimental data for NASA R67 rotor. Blade-to-Blade Mach number distributions are compared to confirm the accuracy of the code. From the results, it is concluded that Abid'k-$\omega$ model is better for the calculation of flow rate and efficiency than Baldwin-Lomax model. But, the predictions for Mach number and shock structure are almost the same.

• Journal of Animal Environmental Science
• /
• v.1 no.1
• /
• pp.9-19
• /
• 1995

This study was carried out to investigate the effect of sawdust bedding barn on manure handing, management labour and physiological aspect of dairy cows, and then to establish the criteria on the optimum utilization method of sawdust bedding barn. 46 tie stall barns and 49 sawdust bedding barns were surveyed to cmopare the milk productivity between two different barns, and also 5 tie stall barns, 15 sawdust bedding barns and 1 rice hull bedding barn were selected to study the utilization situation of sawdust barn in Kyung-Ki province area. The major results obtained were as follows; 1. The roof material of sawdust barn were consisted of 66% vinyl house, 23% PVC light and 11% slate and galvanum coated tin. Most of the floor structure was earth ground with the rate of the approximately 82%. 2. The average occupied area of sawdust bed per cow was 15.2 $m^2$, depth that 30 cm and the utilization period was 12 months. 3. Milk Yield was significantly higher at sawdust barn than at tie stall barn(P<0.01). Bacterial and somatic cell count in raw milk were less at the sawdust barn than in tie stall barn. However, there was not significance difference between two barns. 4. The labour hour needed to cow management in the sawdust barn was approximately 48% of that of tie stall barn. 5. The temperature and moisture content measured in sawdust bed were closely affected by seasonal ambient temperature. The skin and hair of cow were much cleaner at the PVC light roofed sawdust barn than any other roof materials. 6. The additives used for improving of fermentation did not show any effect on temperature and moisture content in sawdust bed. When the ambient temperature was $30.4^{\circ}C$, the surface temperature of measured 1 cm above the sawdust bed was $12.2^{\circ}C$ lower and the temperature of 100 cm above the sawdust bed was $2.4^{\circ}C lower under shading net facility than that of vinyl roofed one.7. The hoof length of miking cow was 7.95 cm in tie stall and 9.19 cm in sawdust barn with high significance (P<0.01). And disease occurence such as mastitis and foot-rot tended to decrease in the sawdust barn. 8. The number of total bacteria and coliform bacteria were less in the sawdust bed compared with earth ground resting area. And a parasite strongyloides papillosus was detected but without any infected cow. 9. The nitrate($NO_3N$) content in non-roofed earth ground resting area and earth ground under the sawdust bed was likely to pollute the ground water. 10. In economic point of view, rice hull bedding barn was the cheapest among different systems. And in the sawdust bedding barn PVC light + slate roofed barn was most desirable, and vinyl roofed one the least.

• Asian-Australasian Journal of Animal Sciences
• /
• v.32 no.5
• /
• pp.748-756
• /
• 2019

Objective: The objective of this study was to examine the effect of using a tunnel ventilation system within the dairy barn environment upon the productivity of dairy cows during the winter season. Methods: The study was performed at the University Farm, Faculty of Agriculture, Utsunomiya University. Twenty-one Holstein dairy cows (5 heifers and 16 multiparous) were enclosed in a stall barn. Unventilated (UV) and tunnel-ventilated (TV) was operated by turns every other week, and a number of key parameters were measured in the barn, including tunnel ventilation output, temperature, relative humidity, gas concentrations (oxygen [$O_2$], carbon dioxide [$CO_2$], and ammonia [$NH_3$]). Also, skin and rectal temperature, respiratory rate, blood gas concentrations, and bacterial count were measured from nipple attachments on ten cows. The amount of fodder left uneaten, and general components and somatic cell count of the milk were measured. Results: As for our dairy barn environment, air temperature dropped significantly with the passage of time with TV. Humidity was significantly higher with TV at 0600 h compared to UV, while $CO_2$ and $NH_3$ concentrations with UV were significantly higher than with TV at 0000 h and 0600 h. Skin temperature was significantly lower with TV compared to UV at 0000 h and 0600 h. Respiratory rate was also significantly lower at 0600 h with TV than with UV. Bacterial count for the nipple attachments was significantly lower with TV than with UV at 0600 h. The amount of leftover fodder was significantly less with TV in comparison with UV. Conclusion: Our results suggest that a TV system in the winter barn results in environmental improvements, such as reductions in unfavorable gas concentrations and bacterial growth. Consequently, it is expected that barns utilizing a TV system will be beneficial for both animal health and production.

• Journal of Animal Science and Technology
• /
• v.48 no.3
• /
• pp.479-486
• /
• 2006

The current study was conducted to examine the effect of feeding and management practices on milk quality and dairy farm productivity in Korea. Fifty dairy farms in Gyunggi (11), Gangwon (22), Chungnam (17) provinces were surveyed to collect data on the herd size, housing style, feeding management, waste disposal, milking practices and milk yield. Milk tank samples from all farms under study were also collected to enumerate its composition and quality parameters. Large dairy herds are equiped with better housing, milking and waste control facilities than medium and small dairy herds. Higher concentrate feeding to lactating cows was noticed in small dairy herds (47.51 %) than in medium (32.59 %) and large dairy herds (31.82 %). The decrease in concentrate feeding to lactating cows with increase in number of cows per farm resulted in a simultaneous increase in the use of imported forages. Bacterial count in milk was affected by housing and milking facilities at dairy farms. Higher bacterial counts (Coliform and E. coli) in milk were observed in cows housed in stanchion than those under free stall with saw dust bedding. The bacterial counts were higher with bucket milking system than with pipe-line and parlour systems. The increase in the number of dairy cows per farm and thus better management and milking facilities resulted in a reduction in somatic cell score. Milk yield (per cow) was higher in herds with less somatic cell score. Average milk protein concentration was between 2.89 to 2.98 % and milk urea nitrogen was between 21.81 to 23.31mg/ml on surveyed dairy farms. This study concluded that large herd size with better dairy cow management facilities is crucial to produce quality milk with better dairy farm income.