• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.4
• /
• pp.353-358
• /
• 2014

This paper reports a simple, yet effective 1-step surface modification method for stainless steel. Electrochemical etching in dilute Aqua Regia forms hierarchical micro and nanoscale structure on the surface. The surface becomes highly hydrophobic (${\sim}150^{\circ}$) as a result of the etching in terms of static contact angle (CA). However the liquid drops easily pinned on the surface because of high contact angle hysteresis (CAH), which is called a "petal effect": The petal effect occur because of gap between surface microstructures, despite of intrinsic hydrophobicity of the base material. The pore size and period of surface structure can be controlled by applied voltage during the etching. This method can be applied to wide variety of industrial demand for surface modification, while maintaining the advantageous anti-corrosion property of stainless steel.

• 연구논문집
• /
• s.23
• /
• pp.29-43
• /
• 1993

Photoetching of AISI 304 stainless steel in ferric chloride solution has been studied. This paper investigated on the single side etching characteristics of 304 stainless steel, especially influence of etching temperature, spray pressure of ferric chloride etchant, and etching time with $50\mum$ and $75\mum$ line width photomask.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.532-540
• /
• 2012

In this study, some considerations have been suggested in developing on-site techniques to evaluate the sensitization of stainless steels. Electrochemical potentiokinetic reactivation (EPR) technique is known to be a candidate tool for field applications since it enables quantitative assessment in reasonable test time, compared to oxalic etching (ditch) technique. The on-site application of the test method imposes additional restrictions on the selection of the test method (for example, minimum surface preparation requirement, insensitivity to testing temperature, etc.). The EPR and etching techniques have been compared in order to sensitization of stainless steel structures. It has been widely reported that the maximum sensitivity in the welded structure of stainless steel is shown at heat-affected zone (HAZ) than weldments with cast structure. In this work, sectioned weldments and external surfaces were investigated to reveal the degree of sensitization by the etching and the results were compared with those of EPR test. The EPR test showed little sensitivity to surface roughness and test temperature.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.157-165
• /
• 1993

The potentiostatic etching dissolution method, which had been used for the quantification of precipitates in steel, was applied to investigate the origin of cracks occurred in 304 stainless steel during processing. The morphology of crack propagation was observed by SEM. EDS and EPMA were used for the analysis of chemical composition of large precipitates on the grain boundary. The crystal structure of these large precipitates was determined by X-ray diffraction and electron diffraction. In both a stainless steel plate and a wire, the crack propagated along the grain boundary. Large precipitates on the grain boundary were identified to be $M_2C$ and $M_{23}C_6$. Potentiostatic etching dissolution method was found to be appropriate to the sample preparation for the analysis of precipitates in stainless steel.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.211-216
• /
• 2012

Wet chemical etching of stainless steel foil by aqueous ferric chloride solution was investigated in this study. Effects of various process parameters (e.g. etchant agitation rate, etchant temperature, $Fe^{3+}$ ion concentration, free HCl concentration, specific gravity, etc.) on the etch rate was first studied, and it was found that the etch rate of AK (aluminum-killed) steel, chromium metal and stainless steel (STS430J1L alloy) follows the pseudo-first order reaction equation. When the fatigue ratio of etchant was kept under 16%, sludge was not formed in the solution, and the etched surface showed smooth roughness. The etch rate decreases as Baume of etchant increases, but the effect of free HCl concentration on the etch rate turned out to be minimal. Experimental data were compared with the calculated results from modeled equation, showing very good agreement.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.1
• /
• pp.219-226
• /
• 2002

The mechanical etching technique has recently been developed to a powder blasting technique for various materials, capable of producing micro structures larger than 100$\mu$ m. This paper describes the performance of powder blasting technique in micro-pocketing of stainless steel and the effect of the number of nozzle scanning and the nozzle height on the depth and width of pockets. Experimental results showed that increasing the no. of nozzle scanning and decreasing the nozzle height resulted in the increase of depth and width in pockets. Increase of width results from wear of mask film.

• Journal of Korea Foundry Society
• /
• v.25 no.3
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.244-249
• /
• 2023

This paper presents a comprehensive analysis of the impact of surface roughness on the friction and wear properties of SUS 321, an austenitic stainless steel variant produced using the laser powder bed fusion (LPBF) technique, which is a prevalent additive manufacturing method. After the LPBF fabrication, the specimens go a heat treatment process aimed at alleviating residual stress. Subsequently, they are polished extensively to achieve a refined and smooth surface. To deliberately introduce controlled variations in surface roughness, an etching process is employed. This multi-step method encompassed primary etching in a 3M hydrochloric acid solution, followed by secondary etching in a 35 wt% ferric chloride solution, with varying durations applied to different specimens. A comprehensive evaluation of the surface characteristics ensued, employing precise techniques such as surface roughness measurements and meticulous assessments of water droplet contact angles. Following the surface treatment procedures, a series of friction tests are performed to explore the tribological behavior of the etched specimens. This in-depth investigation reached its peak by revealing valuable insights. It clarified a strong correlation between intentionally altered surface roughness, achieved through etching processes, and the resulting tribological performance of LPBF-fabricated SUS 321 stainless steel. This significantly advances our grasp of material behavior in tribological applications.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.1-10
• /
• 1992

Three chemical precleaning methods-degreasing, electropolishing and acidic etching-suitable for stainless steel vacuum chamber have been studied and compared. The techniques used in evaluating and comparing the three treatments include Auger analysis and the measurement of the outgassing rate. The obtained outgassing rates (N2 equivalent) are 1.1 $\times$ 10-10torr l/s cm2 and 3.9 $\times$ 10-11torr l/s cm2 for degreasing electropolishing, and etching method, respectively, after 48 hours from the initial pumpdown at room temperature. A simple model is introduced to analyze the pumpdown curve. Some surface parameters, such as surface coverage, mean residence time, and desorption energy, are calculated from corresponding equations derived from this model.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.42-46
• /
• 2004

0.5mm thick steel is used to manufacture nail files. The first process is blanking the blank and then make about 300 holes of 0.8$\~$1.0mm in diameter. This process depends mainly on etching which takes $33\%$ of manufacturing cost and it can make manufacturing cost rise. The residual etching reagent is not environmentally friendly and the steel material is apt to rust as well. The key accomplishments of this research are to change the material from steel to stainless and develop a progressive perforating die in place of etching process.