• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.5
• /
• pp.1215-1223
• /
• 2014

In multi-hop wireless networks, a message transmission path is set up on demand by a route discovery step, where a shortest path is used in general. The shortest path, however, normally uses the nodes near the center area, which causes a high traffic load in that area and reduces the message transmission reliability. We propose a stable routing protocol considering the remaining energy of nodes. Our protocol uses ETX as a link performance estimator and tries to avoid the nodes with smaller energy. By doing this, we can reduce the route failure probability and packet loss. We have evaluated the performance of the proposed protocol using QualNet and compared with AODV and MRFR protocols. The simulation result shows that our protocol has a similar performance as MRFR in terms of end-to-end message reception ratio, average message delay and delay jitter, but outperforms MRFR in terms of traffic load distribution.

• Journal of KIISE:Information Networking
• /
• v.34 no.5
• /
• pp.340-347
• /
• 2007

Vehicle safety service can be effectively achieved with inter-vehicle communication technologies, in which moving vehicles transmit a safety related urgency information such as traffic accidents, sudden stops, obstacle appearance etc. They usually utilize a broadcast of message propagation method because the communicating vehicles are not known each other. The pure broadcasting scheme does not satisfy the requirements of vehicle safety communication service due to the transmission delay with frequent message collisions. To resolve this problem, this paper presents a group based propagation method for the multi-hop transmission, in order to deliver an urgency message to the reasonable size of vehicle troop. A group header is elected in considering of the position information of vehicles and radio transmission range. And a vehicle equivalent group is formed with the header. With benefits of the group based transmission, it is possible to minimize the unnecessary transmission and the possibility of message collisions. Simulation results show that the message propagation performance is so stable regardless of vehicle's congestion degree.

• Journal of Korea Multimedia Society
• /
• v.15 no.3
• /
• pp.372-379
• /
• 2012

This paper presents a group based propagation method for multi-hop transmission, in order to deliver an emergency message to the reasonable size of vehicle troop. A group head is selected in considering of the position information of vehicles and radio transmission range. With benefits of the group based transmission, it is possible to minimize the unnecessary transmissions and the possibility of message collisions. We evaluate the performance of the proposed scheme compared with conventional schemes. Simulation results show that the message propagation performance is so stable regardless of vehicle's congestion degree.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.3B
• /
• pp.526-535
• /
• 2010

In this paper, we propose the fault-tolerant network-based mobility management scheme for supporting multimedia services of broadcasting & communications convergence in fixed mobile convergence (FMC) networks. The proposed scheme is based on AIMS (Access Independent Mobility Service) which is developed for the mobility support among heterogeneous access networks. To support stable location management and handover control for a MN, the proposed scheme supports stable management of binding information by sensing network attachment and detachment of a mobile node (MN). In addition, the proposed fault-tolerant (FT) AIMS supports a function of message retransmission for the support of handover control message and a function of heartbeat message transmission for the support of stable access network environments to a mobile node. We evaluate and analyze the performance of the proposed scheme through the implementation of AIMS system test-bed.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.6 no.4
• /
• pp.57-65
• /
• 2010

Application of WBAN technology in medical field facilitates the prevention of diseases by collecting the vital signs remotely. It also enables to prevent the accidental emergency situation in advance plus long-tem monitoring of patients with chronic diseases such as heart diseases, hypertension, or the elderly and infirm. For emergency patients, major vital signal information collected by the 'Sensing' should have the top priority and such information should be transferred as promptly as possible without competition. In addition, when an emergency occurs to a patient, a priority mechanism is necessitated for a urgent message to get through to the final destination. However, LR-WPAN IEEE 802.15.4 technology does not consider such emergency message handling features. To deal with aforementioned issues, the IEEE 802.15.4 super frame protocol structure has been designed for stable transfer of emergency information in WBAN environment in this study, and alternation to super frame structures have been made, allowing GTS(Guaranteed Time Slot) can be used first at CFP (Contention Free Period) by reserving the resources in advance and prioritize the emergency signals. NS-2 has been utilized for the performance test and analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.5B
• /
• pp.480-488
• /
• 2009

A mobile ad-hoc network is an autonomous collection of wireless mobile nodes that organizes a temporary network without any network infrastructure. Due to node mobility, it is a challenging task to maintain the network topology. In this paper, we propose a stable clustering algorithm that uses node mobility for cluster formation. In the proposed algorithm, the node mobility is measured by counting the number of nodes entering into/leaving from its transmission range. The node having the lowest mobility is selected as a cluster head. For topology maintenance with reduced control overhead, the cluster head adaptively controls the broadcasting period of hello message to the measured node mobility. Through computer simulations, it is verified that the proposed algorithm outperforms previous clustering algorithms in terms of control overhead, the rate of node mobility changes and the number of cluster head changes.

• Journal of KIISE:Information Networking
• /
• v.29 no.3
• /
• pp.224-232
• /
• 2002

The routing protocols designed for wired networks can hardly be used for mobile ad-hoc networks due to limited bandwidth of wireless transmission and unpredictable topological change. Recently, several routing protocols for mobile ad-hoc networks have been proposed. However, when these protocols are applied to support real time services like multimedia transmission, they still have problems in ad-hoe networks, where the topology changes drastically. In this paper, we propose a new route selection algorithm which selects the most reliable rouse that is impervious to route failures by topological changes by mobile hosts. For reliable route selection, the concept of virtual zone (stable lone and caution zone) is proposed. The lone is located in a mobile node's transmission range and determined by mobile node's mobility information received by Global Positioning System (GPS). The proposed algorithm is applied to the route discovery procedure of the existing on-demand routing protocol, AODV, and evaluated by simulation in various traffic conditions and mobility patterns.

• Journal of IKEEE
• /
• v.9 no.1 s.16
• /
• pp.31-39
• /
• 2005

This paper presented new biometrics data transfer model, and use MD5 (Message Digest5) and RSA (Ron Rivest, Adi Shamir, Len Adleman) algorithm to improve biometrics data's security. So, did so that can run user authentication more safely. That is, do so that may input fingerprint among biometrics through client, and transmit processed fingerprint to server. When fingerprint information is transmitted, it uses MD5 algorithm to solve problem that get seized unlawful living body information from outside and information does Digest. And did to pass through process that transmit again this by RSA method. Also, experimented general text data and living body data that is not encoded, transmission speed and security of living body data that encoding and transmit each comparison. By running user authentication through such improved method, is expected to be applied in several. fields by method to simplify certification procedure and is little more correct and stable.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.443-450
• /
• 2012

As power grids are integrated into one big umbrella (i.e., Smart Grid), communication network plays a key role in reliable and stable operation of power grids. For successful operation of smart grid, interoperability and security issues must be resolved. Security means providing network system integrity, authentication, and confidentiality service. For a cyber-attack to a power grid system, which may jeopardize the national security, vulnerability of communication infrastructure has a serious impact on the power grid network. While security aspects of power grid network have been studied much, security mechanisms are rarely adopted in power gird communication network. For security issues, strict timing requirements are defined in IEC 61850 for mission critical messages (i.e., GOOSE). In this paper, we apply security algorithms (i.e., MD-5, SHA-1, and RSA) and measure their processing time and transmission delay of secured mission critical messages. The results show the algorithms satisfying the timing requirements defined in IEC 61850 and we observer the algorithm that is optimal for secure communication of mission critical messages. Numerical analysis shows that SHA-1 is preferable for secure GOOSE message sending.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.135-140
• /
• 2019

Lattice towers and tubular steel poles have been commonly used for electrical power transmission in Korea. They are durable, structurally stable, simple and can easily be constructed in limited spaces. However, residents are opposed to construct transmission lattice towers in their areas because they are not visually attractive, and electrical field occur at the transmission lines. Underground transmissions have been used instead of the traditional towers to resolve these problems, however they are not cost effective to construct and run. Therefore, we have developed eco-friendly towers that are more attractive, well blending into the surrounding environment, and much more economical than underground transmissions. There are four categories of the eco-friendly electric transmission towers about design aspects. Firstly, there is decoration type such as tree tower and ensemble tower. Tree tower looks like actual trees with leaves and branches so it blends into surroundings. Ensemble towers were designed after pair of crane birds. Those towers have decoration features and art works. Structural examination and manufacturing this type would be very similar to the conventional transmission towers. Secondly, there is arm design type such as traditional tower. Design features are added to the existing towers. As partial design can be adoptable on these types, it can easily meet height regulations and attach to conventional lattice towers and tubular steel poles. Also, these towers are more economical than others. Third category is multipurpose type such as Sail Tower. These towers have simple pole or tubular structure with features which can be used as information message board, public relations and much more. This type will face greater wind pressure because of the area of the board, also visibility must take into consideration. Lastly, there is moulding type such as arc pylon. It is different shape to the conventional towers - lattice towers and tubular steel poles. Dramatic design changes have been adapted - from a hard and static tower to a soft and curved tower. These towers will well stand out in the field. However, structural examination and manufacturing this type would be difficult and costly. Also certain towers of this type would require scaffolding or false work to construct, which will result in limitations of the construction area. This paper shows KEPCO 154 kV Sail tower in detail. KEPCO 154 kV Sail tower that is included in fabrication of sample tower and tower testing has developed and the results are presented in this paper. We hope that sail tower is also considered as a solution to have public acceptance or to create a familiar atmosphere among towers and people in coastal area.