• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.197-204
• /
• 2007

Tunnel deformation happens by excavation. After installation of support, tunnel is gradually stabilized over time. Effect of excavation on tunnel behavior decreases as increase of distance from face. If the time that the displacement converges by tunnel stabilization is estimated, processes after stabilization can be advanced and economic loss can be reduced. In this study, the distance of displacement convergent point from face in the tunnel constructed on sedimentary rock is estimated using control chart method. As the results of analysis using a control of chart, displacements in a sedimentary rock tunnel are converged within 100 m from each tunnel face.

• The Journal of Engineering Geology
• /
• v.25 no.1
• /
• pp.9-20
• /
• 2015

A strainmeter goes through a period of instability immediately after installation. To determine the stability of strainmeters installed around the Andong fault zone, South Korea, an x-MR control chart analysis and a T² control chart analysis were conducted. The x-MR control chart analysis used an empirically determined 3σ control limit line to identify abnormal data in recently installed strain gauges. In the T² control chart analysis, the control limit line was set at a confidence of 95%. A comparison of the early stage of measurement with the terminal stage of measurement for three months after installation indicates that stabilization depends on the location and direction of each strain gauge in x-MR control chart analysis. In the T² control chart analysis, the number of values exceeding the control limit line decreased as the terminal stage was approached. Based on these results, it is suggested that the 3σ control limit line of an x-MR control chart can be used as a standard for single gauge stability, and that the 95% confidence limit of a T² control chart analysis could be used as the standard for the stability of multi-gauge strainmeters.

• The Journal of Engineering Geology
• /
• v.19 no.3
• /
• pp.261-268
• /
• 2009

Tunnel measurements provide crucial information on the ground stability during the excavation, visualizing the ground behavioral characteristics with quantitative dada. Generally, the frequency of the measurements is greater during the early stage of the tunnelling process and reduced with time. However, there are no quantitative criteria established for either the activities, such as the time, location and frequency of the measurement or the management guidance, especially for the site of subtle and unexpected displacement during the excavation. It is, however, still challenging to assess behavioral characteristics of subtle and unexpected displacement after stabilization. In this study, we propose a new method to assess stability and to analysis the behavioral characteristics of subtle and unexpected displacement after stabilization using statistic control charts of displacements. We also present a test result on the applicability of control chart and CUSUM control chart to measured displacements.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.39 no.1
• /
• pp.140-152
• /
• 2016

It is very important for the competitiveness and sustainable management of enterprises that the rapid changes in the managerial environments quickly and accurately are responded. For example, the large-scale investment accompanied by bad alternatives in accordance with misunderstanding of the managerial environments yields the huge cost and effort to modify and improve. In firm management, the quality of products and the productivity are influenced by changes of the endogenous factors yielded in manufacturing process and the exogenous factors as market, etc. These changes include not only changes in 4M (man, machine, material, method) but also those in the market, competitors, and technologies in the process of commodification, i.e., first, such disturbances make dispersion of the process big and odd. By Shewhart chart it can be checked that the process monitored is control-in or out. Business administration executes activities for input stabilization by monitoring changes in 4Ms, comparing with the standards, and taking measures for any abnormality. Second, TRM (technology road map) is to prospect product deployment and technological trend by predicting technologies in the competitive environment as the market, and to suggest the future directions of business. So, TRM must be modified and improved according to DR (design review) stages and changes in mass-production like input material change. Therefore, a role of TRM in input stabilization for reducing cost and man-hour is important. This study purposed to suggest that the environment changes are classified into endogenous factors and exogenous factors in production process, and then, quality and productivity should be stabilized efficiently through connection between TRM and input stabilization, and to prove that it is more effective for the display industry to connect TRM with input stabilization rather than to use TRM separately.

• Journal of the Korean Data and Information Science Society
• /
• v.13 no.2
• /
• pp.285-294
• /
• 2002

The control chart is widely used tool for monitoring of the process. This paper deals with an interpretation of the process capability index(PCI) and process performance index(PPI) when the control chart is used for monitoring of the process. The main difference between the PCI and PPI is how we did estimate the process deviation. The PCI uses the within process variation and the PPI uses the total process variation, which is conceptually defined as sum of between process variation and within process variation. Easy interpretations of the PCI and PPI for field engineers are described. And some new approaches to interpretation of the process capability and performance index may be useful in early stabilization of new process.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.5
• /
• pp.959-961
• /
• 2011

Manure-based composts can have detrimental effects on the agricultural lands and crops if they are applied without proper stabilization process. Composting is well-known method for the stabilization of manure-based composts and the extent of composting could be examined by maturity test. Among various methods to examine compost maturity, the performances of two mechanical methods (Solvita and CoMMe-100) were examined and the test results were compared with seed germination test. The mechanical methods are considered to be simple and relatively objective. Also they are cost- and time-efficient. Ten commercially available composts collected in Korea were used for this study. Basically, the maturity determined with these mechanical methods was in good agreement with the seed germination test. However, it appeared that the index levels of compost maturity indicated more maturity by CoMMe-100 than Solvita for the same compost. The differences between maturity index levels determined by both methods were able to be minimized through extending the reaction time for CoMMe-100 and adjusting index level for maturity determination in the standard color chart.

• Journal of Korean Society for Quality Management
• /
• v.26 no.2
• /
• pp.106-117
• /
• 1998

The following study has been undertaken to build QIP (Quality Improvement Process) of an inner-layer process in a PCB (Printed Circuit Board) manufacturing plant. The objective of the study is stabilization and optimization of the process through quality improvement. To do that, defective factors in process are gathered by the cause and effect analysis and classified by PFD (Process Flow Diagram), key factors are found out by PFMECA (Process Failure Mode and Effect Criticalty Analisis), DOE(Design of Experiments) is a, pp.ied to those key factors to optimize the process, SPC (Statistical Process Control) chart is used to maintain the optimal conditions of the process and to improve quality continuously, and a quality management system is developed to improve quality mind and quality system for the PCB jmanufacturing plant. Overall, QIP is established to improve quality for the PCB manufacturing plant in the study.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.461-465
• /
• 2007

MANET(Mobile Ad hoc Networks) is free-mobility formation of mobile nodes in the wireless networks. Generally, wireless networks has two main type of structures which Tree and Mesh. These general structure is difficult to do which connectivity, redundancy transmit and network continuant. In this paper, we would suggest a new ODDMRP(Ontology Doppler effect-based Dynamic Multicast Routing Protocol) technology for effective MANET which Ontology Doppler effect-based. ODDMRP consist of the parameters for node entropy when using Doppler effect which moving position of round node, moving time, and distribution chart in velocity also it express distance of destination node and property structure organization. It would be used to provide improvement to keep the optimal communication routing and also could be improve network stabilization, and continuation durability of connectivity.

• Environmental Engineering Research
• /
• v.19 no.3
• /
• pp.261-268
• /
• 2014

Leachate quality and methane emission from pilot-scale lysimeters operated under semi-aerobic and anaerobic conditions were monitored for 650 days. Two semi-aerobic lysimeters were filled with un-compacted and compacted municipal solid wastes whereas two anaerobic lysimeters containing compacted wastes were operated with leachate storage at 50% and 100% of waste height, respectively. Despite having high moisture in wastes and operating under tropical rainfall events, leachate stabilization in semi-aerobic lysimeters took place much faster resulting in BOD reduction by 90% within 60 days, significantly shorter than 180-210 days observed in anaerobic lysimeters. Nitrogen concentration in leachate from semi-aerobic lysimeter could be reduced by 90%. In term of gas emission, semi-aerobic lysimeter with un-compacted wastes had much lower methane emission rate of $2.8g/m^2/day$ compare to anaerobic lysimeters ($62.6g/m^2/day$) through seasonal fluctuation was observed. Nevertheless, semi-aerobic lysimeter with waste compaction has similar performance to anaerobic lysimeter.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.252-256
• /
• 2001

The rapid development of communication equipment and information processing technology has led to a constant improvement in cordless communication. Lithium ion batteries used in cellular phones and laptop computers, in particular, have been in the forefront of the above revolution. These batteries use high value added raw materials and have a high and stable energy output and are increasingly coming into common use. The development of the material for the negative terminal has led to an improvement in the quality and efficiency of the batteries, whereas a reduction in the cost of the battery by researching new materials for the positive anode has become a research theme by itself. These long life batteries, it is being increasingly realized, can have value added to them by recycling. Research is increasingly being done on recycling the aluminum case and the load casing for the negative diode. This paper aims to introduce the current situation of recycling of lithium ion batteries. 1. Introduction 2. Various types of batteries and the situation of their recycling and the facts regarding recycling. 3. Example of cobalt recycling from waste Lithium ion secondary cell. 3-1) Flow Chart of Lithium ion battery recycling 3-2) Materials that make a lithium ion secondary cell. 3-3) Coarse grinding of Lithium ion secondary cell, and stabilization of current discharge 3-4) Burning 3-5) Grinding 3-6) Magnetic Separation 3-7) Dry sieving 3-8) Dry Classifying 3-9) Content Ratio of recycled cobalt parts 3-10) Summary of the Line used for the recovery of Cobalt from waste Lithium ion battery. 4. Conclusion.