• Journal of the Korean Wood Science and Technology
• /
• 제16권3호
• /
• pp.48-64
• /
• 1988

This study was carried out to investigate the free vibrational properties of traditional and replaceable species for sounding board, using piezoelectrical accelerometer and signal analyzer. In the study, the frequency equations of free-free beam carrying a concentrated mass in the transverse vibration and of free-mass beam in the longitudinal vibration were used. The results obtained were as follows. 1. Average values of dynamic modulus of rigidity of Korean commercial species measured were as follows. Paulownia tomatosa (Thunb.) Steudel: $5.590\times10^9\;dyne/cm^2$ Tilia amurensis Rupr.: $5.414\times10^9\;dyne/cm^2$ Macckia amurensis Rupr.: $10.044\times10^9\;dyne/cm^2$ Fraxinus mandshurica Rupr.: $8.876\times10^9\;dyne/cm^2$ Ulmus davidiana var.japonica Nakai: $8.677\times10^9\;dyne/cm^2$ Pinus rigida Miller: $6.33\times10^9\;dyne/cm^2$ Fraxinus rhynchophylla Hance: $4.666\times10^9\;dyne/cm^2$ 2. The ratio of dynamic transverse Young's modulus to dynamic modulus of rigidity, $E_T/G_{LT}$, was 24.922 for Fraxinus rhynchophylla Hance, which was the highest, 7.317 for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. 3. The value of longitudinal dynamic Young's modulus was about 3.7% and 19.8%, respectively, higher than those of transverse dynamic and static Young's modulus. The value of transverse dynamic Young's modulus was about 15.5% higher than that of static Young's modulus. 4. Predicted value of MOR in terms of correlation coefficient by transverse dynamic Young's modulus was slightly higher than that of static Young's modulus, but no significance was found out. 5. Transverse dynamic Youne's modulus was $(2.002\pm0.288)\times10^{11}\;dyne/cm^2$ for Fraxinus mandshurlca Rupr., which was the highest, $(0.601\pm0.100)\times10^{11}\;dyne/cm^2$ for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. The sound velocity of sitka spruce was 5,685 m/sec, which was the highest. 6. Internal friction of Paulownia tomentosa (Thunb.) Steudel was shown the lowest value among Korean commercial species, $(8.795\pm1.795)\times10^{-3}$, but was higher than that of sitka spruce, $(7.331\pm0.991)\times10^{-3}$. Internal friction was shown negative correlation with density and dynamic Young's modulus, respectively. 7. K value was affected largely by internal friction and was the highest, $2.225\times10^8$ for Paulownia tomentosa (Thunb.) Steudel and was the lowest, $0.550\times10^8$ for Fraxinus rhynchophylla Hance. K value of Paulownia tomentosa (Thunb.) Steudel was higher than that of sitka spruce and K values of melapi and cottonwood, which have been considered to be replaceable species with sitka spruce in the piano industry, were lower than those of Paulownia tomentosa (Thunb.) Steudel and mill amurensis Rupr.

• Journal of the Korean Wood Science and Technology
• /
• 제17권2호
• /
• pp.26-33
• /
• 1989

The acoustic absorption coefficient and acoustic impedance of 5 species of softwood(sonamoo, sam namoo, gusang namoo, hwaback, sitka spruce) and 5 species of hardwood (Mulgusul namoo, Italian popular, white meranti, red meranti, kalantas) were measured by the standing wave method. which is simple in the setup and gives more accurate result than does any other measuring method. The dependence of the absorption coefficient and complex acoustic impedance on the wood sections. thickness of the sample itself and the back air gap was investigated experimentally in the frequency range from 200Hz to 1800Hz, and the result are as follows: 1. The acoustic absorption coefficient of wood sections was higher on the cross section than radial and tangential sections. 2) The acoustic absorption coefficient were higher in the frequency range from 400Hz to 600Hz, but decreased in the frequency above 600Hz. 3. The genenal tendency of the variation of the normal acoustic impedance was increased according to the frequency. 4. The acoustic absortion coefficient was increased in the to 7mm-thick sample and decreased in 9mm-thick sample. 5. The higher acoustic absorption coefficient was shown in the case with the backing an gap than in the case without the gap.

• Environmental Analysis Health and Toxicology
• /
• 제22권4호
• /
• pp.339-348
• /
• 2007

A laboratory experiment was conducted to study the characteristics of leaching of Cr, Cu, and As from chromated topper arsenate (CCA)-treated wood. The wood species tested was hemlock spruce ($10\;cm\;{\times}\;10\;cm\;{\times}\;10\;cm\;tube$). The leaching experiment was conducted over 60 days using I L of leachants whose pHs were adjusted to 2.0, 3.7, and 1.6, respectively with nitric acid, and also using lake water, according to the OECD guideline. Each leachate was analyzed for Cr and Cu using flame-AAS, and for As using vapor generation-AAS. Three metals were loathed at the highest levels at pH 2.0 but almost at similar levels at the other conditions. Cumulative quantifies over 60 days of a leaching period were in order of As>Cu>Cr. As was predicted to leach with an increase in flux over a 10 year period, while Cr and Cu fluxes were predicted to decrease with time. This result suggest that arsenic can pose a health risk to humans over a long period of time, when CCA-treated wood is used for building facilities (e.g., playgrounds, residential purposes, etc.) with which humans frequently contact.

• Journal of the Korean Wood Science and Technology
• /
• 제22권4호
• /
• pp.37-42
• /
• 1994

The adsorption of water vapor and equilibrium moisture content(EMC) of the specimens for four softwood species dried by conventional- and high temperature method and equilibrated to 15% of the target EMC condition at 25$^{\circ}C$ were determined by oven drying method and with moisture meters. The amount of adsorption for high temperature dried red pine was significantly higher than that of conventional kiln dried wood, while those of eastern white pine, eastern hemlock and Norway spruce were not significantly different between drying methods. EMCs of these four species determined by oven drying method and with capacitive admittance moisture meter were not significantly different between drying methods. EMC of high temperature dried red pine determined with resistance moisture meter was significantly higher than that of conventional kiln dried wood. But EMCs of other species did not show significant difference between drying methods. EMCs of conventional and high-temperature dried wood determined with electronic moisture meters, especially in the case of the capacitive-admittance moisture meter measurement, were lower than that determined by oven drying method.

• Journal of the Korean Wood Science and Technology
• /
• 제47권3호
• /
• pp.311-323
• /
• 2019

The number of newly constructed traditional Korean houses, i.e., Hanoks, and light-frame buildings is increasing. However, related research is limited owing to the lack of awareness regarding safety evaluations. Therefore, this study conducted an outdoor exposure test to accurately evaluate wooden constructions. Spruce, pine, and fir (SPF) material was monitored for a year, wherein the SPF material was artificially dried under 18% moisture content, and its physical properties and color differences were measured once a month. Large differences were observed in the material's weight and moisture content, which are indexes sensitive to daily range and rainfall; however, no significant difference was found for other basic properties in the pre and post test results. Herein, $L^*$, $a^*$, and $b^*$ values represent color differences; these values exhibited a general decrease after the test. Such differences were attributed to the loss of lignin in the wood. The color difference value was high between the months of May and July, when the daily range and rainfall significantly fluctuated. Multiple regression analysis was performed on the $a^*$ value (redness indicator), daily range, rainfall, and ultraviolet index. The results indicated that the daily range influenced redness the most. According to the estimated regression equation, the daily range and redness are positively correlated. Based on the results, the types and influence of independent variables on color difference are expected to change as the wood's duration of outdoor exposure and the amount of data obtained both increase.

• Journal of the Korean Wood Science and Technology
• /
• 제23권3호
• /
• pp.58-65
• /
• 1995

The possibilities of the estimation of the moisture content(MC) for sitka-spruce (Picea sitchensis Carr.) by measuring density have been investigated. The method is based on the relationships between the wood density and moisture content of wood expressed by Equations (8)~(9). The purpose of this study is examining the estimation of the moisture content of wood by density and the variation of moisture content with annual ring width of wood. The following conclusions were obtained; 1. This method is very convenience because of the average moisture content of wood can be obtained by a simple estimation. This estimation can be made from the easy measurement of the weight and volume of wood. 2. Coefficient of determination between the experimental MCs and theoretical MCs which is calculated by the oven-dry densities of each specimens and Equations (8), (9) is 0.98. This Correlation is very remarkable. Therefore the model Equations on the estimation of moisture content by wood density was available. 3. Relationship between experimental MCs and theoretical MCs which is estimated by average oven-dry density of total specimens showed positive correlation(Fig.2). But from the Fig.4. we can concluded that the number of specimens is two groups. This phenomenon is considered that the variation of MC by the annual ring width from the specimens' observations. Consequently, the MCs of wood by density, is likely to be successful method. can be estimate using by the average oven-dry densities divided with the annual ring widths of wood.

• Journal of the Korean Wood Science and Technology
• /
• 제36권1호
• /
• pp.36-44
• /
• 2008

목조건축물로부터 해체된 고목재를 해당 건축물의 복원이나 새로운 건축물에 재사용하기 위해서는 열화 및 부후 부위를 제외한 건전재의 재질 및 강도성능에 대한 평가가 필요하다. 트러스 현재로 사용된 부재와 사찰에 사용된 부재에 대해 현미경으로 수종식별을 행하고 KS 기준에 따라 각종 물성 및 강도 시험을 행하여 문헌에 의한 결과와 비교 검토하였다. 잎갈나무(Korean larch)는 재질 및 강도 성능이 기존 문헌값보다 높게 나타났으며, 소나무(Korean red pine)와 가문비나무(Yezo spruce)의 경우 해체재의 강도성능이 대체적으로 낮게 나타났다. 육안에 의한 건전부위의 시험편 내의 조직적 열화는 현미경적으로도 관찰되지 않았다. 인장시험편의 중앙부 두께가 5 mm에서 3 mm로 변함에 따라 인장강도가 증가하여 시험편 치수에 대한 검토가 필요한 것으로 판단되었으며, 압축 및 휨 시험법은 현행 기준으로도 적합한 수준이었다. 고목재류에 대한 구체적인 기초 강도 성능평가를 위한 시험방법 및 철물접합부의 접합성능에 대한 차후 연구 검토가 필요한 것으로 평가되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제46권3호
• /
• pp.253-259
• /
• 2018

ACQ 처리 목재에서 약제의 침투깊이를 확인하기 위하여 지금까지는 Cu 성분만을 대상으로 침윤도를 측정해 왔다. 본 연구에서는 Cu 이외에 ACQ의 유효성분 중에 하나인 DDAC의 침투깊이를 조사할 수 있는 DDAC 발색처리 방법을 개발하고 다음과 같은 결론을 얻었다. DDAC 성분은 2',7'-dichlorofluorescein 발색 지시약과 반응하여 진한 주황색으로 발색한다. 이와 같은 발색 반응은 DDAC 용액에서 뿐만 아니라 ACQ 처리 목재에서도 진행되어 DDAC가 침투되어 있는 목재 조직에서는 동일하게 주황색으로 발색한다. 본 연구를 통하여 개발된 DDAC 발색기술에 의하여 방부제 난주입성 수종인 가문비나무에서 Cu에 비하여 DDAC의 목재 침투성이 우수한 사실을 육안으로 확인할 수 있었으며, 다른 난주입성 수종에 대해서도 Cu와 DDAC의 침투성 차이를 조사할 필요가 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제48권2호
• /
• pp.245-252
• /
• 2020

This study was performed to analyze the mechanical properties of tropical hybrid cross-laminated timber (CLT) with bamboo laminated board as the core layer in order to evaluate the possibility of its use as a CLT material. Bamboo board was used as the core layer and the tropical species Acacia mangium willd., from Indonesia, was used as the lamination in the outer layer. The modulus of elasticity (MOE), modulus of rupture (MOR), and shear strength of the hybrid CLT were measured according to APA PRG 320-2018 Standard for Performance-Rated Cross-Laminated Timber. The results show that the bending MOE of the hybrid CLT was found to be 2.76 times higher than SPF (Spruce Pine Fir) CLT. The reason why the high MOE value was shown in bamboo board and hybrid CLT applied bamboo board is because of high elasticity of bamboo fiber. However, the shear strength of the hybrid CLT was 0.8 times lower than shear strength of SPF CLT.

• 한국화재소방학회논문지
• /
• 제26권4호
• /
• pp.18-23
• /
• 2012

이산화탄소 주조법에서 사용되고 있는 방법을 응용하여 목질내에 규산겔과 탄산소다, 이산화규소가 석출된 목재를 제조한 후 외부 복사열원(20, 25, 35 및 50 $kW/m^2$)에 따른 점화시간, 점화온도, 질량감소속도, 임계열유속을 측정하였다. 연구결과, 물유리와 이산화탄소를 이용한 가압함침 처리된 목재는 Pre-Flashover 단계에서의 복사열원(20 $kW/m^2$ 이하)에서 난연성능이 있음을 확인할 수 있었다. 향후 지속적인 연구를 통해 우수한 배합비율을 찾는다면 난연목재로서의 활용가능성이 있다고 판단된다.