• Journal of the Korean Wood Science and Technology
• /
• v.17 no.2
• /
• pp.26-33
• /
• 1989

The acoustic absorption coefficient and acoustic impedance of 5 species of softwood(sonamoo, sam namoo, gusang namoo, hwaback, sitka spruce) and 5 species of hardwood (Mulgusul namoo, Italian popular, white meranti, red meranti, kalantas) were measured by the standing wave method. which is simple in the setup and gives more accurate result than does any other measuring method. The dependence of the absorption coefficient and complex acoustic impedance on the wood sections. thickness of the sample itself and the back air gap was investigated experimentally in the frequency range from 200Hz to 1800Hz, and the result are as follows: 1. The acoustic absorption coefficient of wood sections was higher on the cross section than radial and tangential sections. 2) The acoustic absorption coefficient were higher in the frequency range from 400Hz to 600Hz, but decreased in the frequency above 600Hz. 3. The genenal tendency of the variation of the normal acoustic impedance was increased according to the frequency. 4. The acoustic absortion coefficient was increased in the to 7mm-thick sample and decreased in 9mm-thick sample. 5. The higher acoustic absorption coefficient was shown in the case with the backing an gap than in the case without the gap.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.245-252
• /
• 2020

This study was performed to analyze the mechanical properties of tropical hybrid cross-laminated timber (CLT) with bamboo laminated board as the core layer in order to evaluate the possibility of its use as a CLT material. Bamboo board was used as the core layer and the tropical species Acacia mangium willd., from Indonesia, was used as the lamination in the outer layer. The modulus of elasticity (MOE), modulus of rupture (MOR), and shear strength of the hybrid CLT were measured according to APA PRG 320-2018 Standard for Performance-Rated Cross-Laminated Timber. The results show that the bending MOE of the hybrid CLT was found to be 2.76 times higher than SPF (Spruce Pine Fir) CLT. The reason why the high MOE value was shown in bamboo board and hybrid CLT applied bamboo board is because of high elasticity of bamboo fiber. However, the shear strength of the hybrid CLT was 0.8 times lower than shear strength of SPF CLT.

• Environmental Analysis Health and Toxicology
• /
• v.22 no.4
• /
• pp.339-348
• /
• 2007

A laboratory experiment was conducted to study the characteristics of leaching of Cr, Cu, and As from chromated topper arsenate (CCA)-treated wood. The wood species tested was hemlock spruce ($10\;cm\;{\times}\;10\;cm\;{\times}\;10\;cm\;tube$). The leaching experiment was conducted over 60 days using I L of leachants whose pHs were adjusted to 2.0, 3.7, and 1.6, respectively with nitric acid, and also using lake water, according to the OECD guideline. Each leachate was analyzed for Cr and Cu using flame-AAS, and for As using vapor generation-AAS. Three metals were loathed at the highest levels at pH 2.0 but almost at similar levels at the other conditions. Cumulative quantifies over 60 days of a leaching period were in order of As>Cu>Cr. As was predicted to leach with an increase in flux over a 10 year period, while Cr and Cu fluxes were predicted to decrease with time. This result suggest that arsenic can pose a health risk to humans over a long period of time, when CCA-treated wood is used for building facilities (e.g., playgrounds, residential purposes, etc.) with which humans frequently contact.

• BMB Reports
• /
• v.39 no.6
• /
• pp.782-787
• /
• 2006

A new protein was cloned and identified as the sixth subunit of Choristoneura fumiferana origin recognition complex (CfORC6). The newly identified 43 kDa protein CfORC6 is much bigger than DmORC6 (25.7 kDa) and HsORC6 (28.1 kDa), though it's 23.85% identical to DmORC6 and 23.81% identical to HsORC6. Although the molecular weight of CfORC6 is close to ScORc6 (50 kDa), CfORC6 is only 14.03% identical to ScORC6. By alignment, it was found that the N-terminal of CfORC6 has about 30% identities with other ORC6s, but about 100aa of C-terminal of CfORC6 has no identity with other ORC6s. Like ScORC6, CfORC6 has many potential phosphorylation sites, (S/T)PXK. Like DmORC6, CfORC6 has leucine-rich region in the relevant site. Northern Blot showed that CfORC6 mRNA is about 2,000nt. Southern Blot confirmed that there is one copy of CfORC6 gene in spruce budworm genome. Western blot showed that infection of Cf124T cells with CfMNPV didn't affect the expression levels of CfORC6, at least up to 26 hr post infection.

• Journal of Korean Society of Forest Science
• /
• v.94 no.5 s.162
• /
• pp.321-329
• /
• 2005

Based on the data representing four typical Korean pine forest types, the age structure, DBH distribution, species composition, and forking rule were systemically analyzed for old-growth Korean pine forest in Liangshui Nature Reserve, northeast China. The age structure of Korean pine trees was strongly uneven-aged with one dominated peak following normal distribution, and age of trees varied from 100 to 180 years within a stand. The DBH and height differences in same age class (20 years) varied from 28 cm~64 cm and 5 to 20 m, respectively. Many conifer and hard wood species, such as spruce, fir, costata birch, basswood, oak, and elm, were mixed with dominated trees of Korean pine. The canopy of the old-growth Korean pine forest can be divided into two layers, and differences of mean age and height between Layer I and Layer II were ranged 80~150 years and 7~13 m, respectively. The Weibull function was used to model the diameter distribution and performed well to describe size-class distribution either with a single peak in over-story canopy and inverse J-shape in under-story canopy for old-growth Korean pine stands. The forking height of Korean pine trees ranged from 16m to 24 m (mean 19.4 m) and tree age about 120 to 160 years old. The results will provide a scientific basis to protect and recover the ecosystem of natural old-growth Korean pine and also provide the model in management of Korean pine plantation.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.4
• /
• pp.80-84
• /
• 1991

Lignocellulosic biomass including acetosolv ricestraw and spruce lignin were liquefied and converted into liquid hydrocarbons by catalytic hydroliquefaction reaction. These experimental works were carried out in 1-liter-capacity autoclave using 50% tetralin and m-cresol solution respectively as soluble solvent and Ni. Pd. Fe and red mud as catalyst. $H_2$ gas was supplied into the reactor for escaltion of deoxhydroenolysis reaction. Catalyst concentrations were 1 % of raw material based on weight. The ratio between raw materials and soluble solvent are 1g and 10cc. The reaction conditions are 400-$700^{\circ}C$ of reaction temperature, 10-50 atms of reaction pressure. The highest yield of hydrocarbon, so called "product oil" showed 32% and 5.5% of lowest char formation when red mud was used as catalyst. The product oil yields from those of other catalysts were in the range of 20-29%. The influence of different initial hydrogen pressures was examined in the range d 30-50 atms. A minimum pressure of 35 atms was necessary to obtain a complete recovery of souble solvent for recycling.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.3
• /
• pp.16-25
• /
• 1998

This study was carried out to compare vibrational properties and adsorption among shellac, cashew finished plate and untreated plate of Sitka spruce(Picea sitchensis Carr). By the method of statistical regression modeling, the fundamental resonance frequency of finished plate was higher than that of untreated plate. The fundamental resonance frequency of cashew finished plate was higher than that of shellac finished plate. By the method of modal analysis, mode frequency ratio of cashew finished plate was higher than that of shellac finished plate. Amounts of adsorption of finished plate was lower than that of untreated plate, and amount of adsorption of cashew finished plate was lower than that of shellac finished plate. It was clarified that the vibrational properties and adsorption of finished plate were superior to those of untreated plate. The vibrational properties and adsorption of cashew finished plate was superior to those of shellac finished plate.

• Journal of Plant Biology
• /
• v.25 no.1
• /
• pp.37-53
• /
• 1982

Pollen analysis from lake districts, Youngnangho, Wolhamji and Bangeojin, revealed vegetational patterns in Korea. The pollen stratigraphy was divided into five zones, zone L, I, II, IIIa and IIIb for the past 15,000 years. During zone L (earlier than 10,500 yr BP), late-glacial period, Youngnangho was vegetated with a coniferous forest dominated by spruce, larch, haploxylon pine and fir with considerable amount of herbs. Zone I(10,500~7500 yr BP) was predominantly herbaceous vegetationj with significant amount of oak and diploxylon pine. It suggests that the overall environment became milder and drier than late-glacial period. Zone II(7,500~4,000 yr BP), hypsithermal period, showed significant warming condition, indicated by high pollen concentrations of oak, diploxylon pine and hornbeam, and by more diverse flora of deciduous broad-leaved trees than before. Herbs were not an important part of vegetation. Zone III$^a$(4,000~1,500 yr BP) had pine and oak as main elements. Birch increased slightly while hornbeam decreased in this time. It indicates cooling condition. Zone III$^b$(1,5000-present) which can be called pine period showed obvious human interference. Following forest clearance, agriculture was intensified. The beginning of logging and agriculture was discernible by a sudden decline of arboreal species and by considerable amount of rice, buckwheat, sorrel and plantain. Numerous charcoal fragments were observed in zone I and zone III$^b$.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.4
• /
• pp.37-42
• /
• 1994

The adsorption of water vapor and equilibrium moisture content(EMC) of the specimens for four softwood species dried by conventional- and high temperature method and equilibrated to 15% of the target EMC condition at 25$^{\circ}C$ were determined by oven drying method and with moisture meters. The amount of adsorption for high temperature dried red pine was significantly higher than that of conventional kiln dried wood, while those of eastern white pine, eastern hemlock and Norway spruce were not significantly different between drying methods. EMCs of these four species determined by oven drying method and with capacitive admittance moisture meter were not significantly different between drying methods. EMC of high temperature dried red pine determined with resistance moisture meter was significantly higher than that of conventional kiln dried wood. But EMCs of other species did not show significant difference between drying methods. EMCs of conventional and high-temperature dried wood determined with electronic moisture meters, especially in the case of the capacitive-admittance moisture meter measurement, were lower than that determined by oven drying method.

• Fire Science and Engineering
• /
• v.26 no.4
• /
• pp.18-23
• /
• 2012

After produce the extracted wood to silicic acid gel, sodium carbonate and silicon dioxide with application of the making method for carbon dioxide, ignition time, ignition temperature, mass loss rate and critical heat flux are measured according to external radiation source (20, 25, 35 and 50 $kW/m^2$). From the results, pressure impregnation wood to use with water glass and carbon dioxide has fire retardant performance at heat flux (less than 20 $kW/m^2$) of Pre-Flashover fires. If we find out the excellent maxing ratio through continuously study, it might be decided to be able to be utilized as fire-retardant wood.