• Journal of the Korean GEO-environmental Society
• /
• v.16 no.9
• /
• pp.43-51
• /
• 2015

In this paper, a 3D shell-spring model that can perform time history analysis of buried pipelines is used to evaluate the effect of the incident direction of the earthquake motion. When applying harmonic motions, it is shown that the period of vibration has pronounced influence on the response of buried pipelines. With decrease in the period, the curvature of the pipeline and corresponding response are shown to increase. To evaluate the effect of the incident angle, the motions are applied in the direction of the pipleline, horizontal, and vertical planes. When the motion is applied parallel to the direction of the pipeline, it only induces bending strains and therefore, the response is the lowest. Under motions subjected in horizontal and vertical planes at an angle of $45^{\circ}$ from the longitudinal axis of the buried pipeline, the axial deformation is shown to contribute greatly to the response of the pipelines. When imposing two-components simultaneously, the calculated response is similar to the case where only single-component is imposed. It is because one component only induces bending strain, resulting in very small increase in the response. The trend of the response is shown to be quite similar for recorded motions. Therefore, it is concluded that use of a single-component is sufficient for estimation of the longitudinal response of buried pipelines.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2006.11a
• /
• pp.370-373
• /
• 2006

Lastly, the problem of filling occurs in the process of concealed joint of adjacent components and was seen in joints between the structure and an electrical or mechanical device. Therefore, the dry processing which replaces wet joint was seen in joints between the structure and a door, ones between the structure and a finishing materials, ones between a gypsum board and electrical device, and ones between a water pipe and a tile finishing. And a process of separating the area of jointed parts in order to eliminate the problem of overlap was seen in joints between a door and a finishing material and ones between a gypsum board on the ceiling and a light. Lastly, an analysis of a process of exposing concealed parts indicated that the problem of filling could be applied to joints between the structure and an electrical or mechanical device and ones between a finishing material and a mechanical device. This study sought out methods to apply Environment Friendly Multi Housing Remodeling that allow easy remodeling as part of environment- preserving policies. It also contains basic data useful to implement long-life houses in the future by presenting a comprehensive design standard for them

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2006.11a
• /
• pp.366-369
• /
• 2006

Multi Housing design has not considered the remodeling even at the beginning of the construction. This severely hindered systematic maintenance, providing fundamental causes of consuming society. In general, in about 20 years when the buildings become too old, they are brought down or removed with a trail of waste left behind. In addition, since the current remodeling or future remodeling type is a general remodeling that leaves only a frame, some question the role of the remodeling as a solution to the reconstruction from economically and environmentally efficient aspects. This study intends to find a solution for long-life span multi-family housing design, promoting sequential remodeling by stating the life cycle of components. Problems were identified by analyzing joints, design and construction of multi-family housing based on the previous researches. Conclusion from characterization of the design plan according to joint parts can be summarized as the following firstly, the problem of the wet was seen in joints between the structure and a finishing materials and ones between separate finishing materials. Secondly, the problem of overlap was frequently seen in joints between the structure and a door/window, ones between a door/window and a finishing materials, and ones between a finishing materials and an electrical/mechanical device.

• Steel and Composite Structures
• /
• v.37 no.3
• /
• pp.341-351
• /
• 2020

Steel plate shear wall with self-centering energy dissipation braces (SPSW-SCEDB) is a lateral force-resisting system that exhibits flag-shaped hysteretic responses, which consists of two pre-pressed spring self-centering energy dissipation (PS-SCED) braces and a wall plate connected to horizontal boundary elements only. The present study conducted a series of cyclic tests to study the hysteretic performances of braces in SPSW-SCEDB and the effects of braces on the overall hysteretic characteristics of this system. The SPSW-SCEDB with PS-SCED braces only exhibits excellent self-centering capability and the energy loss caused by the large inclination angle of PS-SCED braces can be compensated by appropriately increasing the friction force. Under the combined effect of the two components, the SPSW-SCEDB exhibits a flag-shaped hysteretic response with large lateral resistance, good energy dissipation and self-centering capabilities. In addition, the wall plate is the primary energy dissipation component and the PS-SCED braces provide supplementary energy dissipation for system. The PS-SCED braces can provide up to 90% self-centering capability for the SPSW-SCEDB system. The compressive bearing capacity of the wall plate should be smaller than the horizontal remaining restoring force of the braces to achieve better self-centering effect of the system.

• Steel and Composite Structures
• /
• v.25 no.5
• /
• pp.625-638
• /
• 2017

This paper presents a novel approach that describes the first-order (linear elastic) partial interaction analysis of members formed by multi-components based on the Generalised Beam Theory (GBT). The novelty relies on its ability to accurately model the partial interaction between the different components forming the cross-section in both longitudinal and transverse directions as well as to consider the cross-sectional deformability. The GBT deformations modes, that consist of the conventional, extensional and shear modes, are determined from the dynamic analyses of the cross-section represented by a planar frame. The partial interaction is specified at each connection interface between two adjacent elements by means of a shear deformable spring distributed along the length of the member. The ease of use of the model is outlined by an application performed on a multi-component member subjected to an eccentric load. The values calculated with an ABAQUS finite element model are used to validate the proposed method. The results of the numerical applications outline the influence of specifying different rigidities for the interface shear connection and in using different order of polynomials for the shape functions specified in the finite element cross-section analysis.

• Journal of Environmental Science International
• /
• v.9 no.1
• /
• pp.1-11
• /
• 2000

A study on the variational characteristics of water quality and phytoplankton biomass by principal component analysis(PCA) was carried out in Kogum-sudo from February to October in 1993. We analyzed PCA on biological factors such as chlorophyll a and phytoplankton cell numbers for centric and pennate diatoms, phytoflagellates, and total phytoplankton as well as physico-chemical factors as water temperature, salinity, transparency, dissolved oxygen(DO), saturation of DO, apparent oxygen utilization (AOU), chemical oxygen demand(COD), nutrient (ammonia, nitrite, nitrate, phosphate and silicate), N/P ratio and suspended solid(SS). The source of nutrients supply depended on the mineralization of organic matters and inputs of seawater from outside rather than runoff of freshwater. The phytoplankton biomass was changed within short interval period by nutrients change. And it was controlled by the combination of several environmental factors, especially of light intensity, ammonia and phosphate. The marine environmental characteristics were determined by the mineralization of organic matters in winter, by runoff of freshwater including high nutrients concentration in spring, by ammonia uptake and high phytoplankton productivity in summer, and phosphate supplied input seawater from outside of Kogeum-sudo in autumn. And Kogum-sudo was separated with 2 regions by score distributions of PCA. That is to say, one region was middle parts of straits which was characterized by the mixing seawater and the accumulated organic matters, other one region was Pungnam Bay and the water around Kogum Island which was done by high phytoplankyon biomass and productivity year-round.

• Journal of Korean Society on Water Environment
• /
• v.30 no.2
• /
• pp.119-127
• /
• 2014

The objective of this study is to evaluate and analyze Sumjin River Basin water environment system. It was necessary to improve the water quality. The data were collected from 2010 January to 2012 December including Water Temperature, pH, DO, EC, $BOD_5$, COD, TOC, SS, T-N, T-P. The data were used to study were required to; Correlation Analysis; Principle Component Analysis; Factor Analysis. The results were as followed. According to correlation analysis on $BOD_5$ against COD, TOC it revealed that the each value of correlation coefficient were 0.715 and 0.719; this means the strength of the relationship is strong. The same analysis on T-P against $BOD_5$, COD, TOC, SS has revealed that the range of the correlation coefficient value fell between 0.482 and 0.608 which means strength of the relationship between them remained normal. Through correlation analysis, it has been found that all elements except T-N have high correlation. The results of principal component analysis to target the overall water quality was extracted to three main components. The cumulative contribution rate is 68.990%. In the case of seasonal water quality, Spring and Summer are extracted to each of four main components. The cumulative contribution rate is 81.515% and 73.550% respectively. Fall and Winter are extracted to each of three main components. The cumulative contribution rate is 65.072% and 72.721% respectively. There is no seasonality in the case of factor analysis. The first common factor is $BOD_5$, COD, TOC, SS, T-P, which were classified. Totally speaking, Sumjin River Basin water system gets highly affected by the nutrient salts, organic matter and suspended solid at the same time.

• Journal of Wetlands Research
• /
• v.21 no.3
• /
• pp.215-223
• /
• 2019

In this study, we analyzed the water quality characteristics of major tributaries of Nakdong River through statistical analysis such as correlation analysis, principal component and factor analysis, and cluster analysis. Organic matter and nutrients are highly correlated, and are high in spring and autumn, and seasonal water quality management is required. Principal component and factor analysis showed that 82% of total variance could be explained by 4 principal components such as organic matter, nutrients, nature, and weather. BOD, COD, TOC, and TP items were analyzed as major influencing factors. As a result of the cluster analysis, the four clusters were classified according to seasonal organic matter and nutrient pollution. Kumho River watershed showed high pollution characteristics in all seasons. Therefore, effective management of water quality in tributary streams requires measures in consideration of spatio-temporal characteristics and multivariate statistical techniques may be useful in water quality management and policy formulation.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.347-355
• /
• 2022

The safety valve (PSV) is a safety device that automatically releases a spring when the pressure generated by various causes reaches the set pressure, and is restored to a normal state when the pressure falls below a certain level. Periodic inspection and monitoring of safety valves are essential so that they can operate normally in abnormal conditions such as pressure rise. However, as the current safety inspection is performed only at a set period, it is difficult to ensure the safety of normal operation. Therefore, evaluation items were developed by finding failure modes and causative factors of safety valves required for safety management. In addition, it is intended to provide decision-making information for securing safety by deriving the priority of items. To this end, a Delphi survey was conducted three times to derive evaluation factors that were judged to be important in relation to the Failure Mode Cause Factor (FMCFs) of the safety valve (PSV) targeting 15 experts. As a result, 6 failure modes of the safety valve and 22 evaluation factors of its sub-factors were selected. In order to analyze the priorities of the evaluation factors selected in this way, the hierarchical structure was schematized, and the hierarchical decision-making method (AHP) was applied to the priority calculation. As a result of the analysis, the failure mode priorities of FMCFs were 'Leakage' (0.226), 'Fail to open' (0.201), 'Fail to relieve req'd capacity' (0.152), 'Open above set pressure' (0.149), 'Spuriously' 'open' (0.146) and 'Stuck open' (0.127) were confirmed in the order. The lower priority of FMCFs is 'PSV component rupture' (0.109), 'Fail to PSV size calculation' (0.068), 'PSV Spring aging' (0.065), 'Erratic opening' (0.059), 'Damage caused by improper installation and handling' (0.058), 'Fail to spring' (0.053), etc. were checked in the order. It is expected that through efficient management of FMCFs that have been prioritized, it will be possible to identify vulnerabilities of safety valves and contribute to improving safety.

• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.79-91
• /
• 1995

Precision forming of electronic components has appeared to be competitive according to manufacturing cost and dimensional tolerances. Now domestic electronic companies have been involving in utilization of the finite element method in process design of precision forming. A forming process to produce an electronic component, aperture, has been inbestigated to find out forming defects during multi-operations. The applications of the commercial FEM software MARC show a possibility of defect in precision coining process among the whole multi-process. Thus the coining process of three-dimensional deformation is analyzed using DAMF-3D which has been developed in this lab with the rigid-plastic algorithm. The result f simulations by DAMF-3D provides clear description of the defect involved in the coining process.