• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.328-331
• /
• 2008

Corrosion behaviour of water intake gate steel structures with different protective measures was investigated. Five material alternatives were taken for investigation, including: imported and recycled stainless steel, carbon steel with hot zinc spraying, painting and composite coatings. Results of corrosion rate for carbon steel, SUS 304, hot zinc spray coats in three water systems of Mekong river basin (saline, blackish and fresh) were also presented. Corrosion rate of carbon steel decreased with decreasing salinity in the investigated water environments. Meanwhile, these values for zinc coated steel, behaved by another way. Environmental data for these systems were filed and discussed in relation with corrosion characteristics. Method of Life Cycle Assessment (LCA) was applied in materials selection for water intake gate construction. From point of Life Cycle Cost (LCA) the following ranking was obtained: Zinc sprayed steel < Recycled stainless steel < Composite coated steel < Painting steel < SUS 304 From investigated results, hot zinc spray coating has been applied as protective measure for steel structures of water intake systems in Mekong river basin.

• Journal of Pharmaceutical Investigation
• /
• v.28 no.1
• /
• pp.7-13
• /
• 1998

The captopril microcapsules were prepared and were investigated by measuring their size distribution using Scanning Electron Microscopy(SEM) and dissolution of captopril. Cetyl alcohol microcapsules prepared by emulsion melted-cooled method with various ratios of drug to cetyl alcohol were spherical and uniform. The release rate of cetyl alcohol microcapsules was decreased proportionally as the content of cetyl alcohol increased but, the particle size of microcapsules was increased. The surface of cetyl alcohol microcapsules was comparatively rough as drug content increased. Pellet type microcapsules were prepared using fluidized-bed coating system by spraying captopril solution on nonpareil-seeds followed by applying $Eudragit^{\circledR}$ RS solution containing propylene glycol as a plasticizer. The release rate of drug from pellet type microcapsules decreased as the content of $Eudragit^{\circledR}$ RS increased.

• Journal of ILASS-Korea
• /
• v.24 no.3
• /
• pp.137-144
• /
• 2019

The Y-jet nozzle has benefits such as simple design and wide operating conditions. Because of these benefits, it is used in various combustion devices including industrial boilers. The most important variables in the design of the Y-jet nozzle are the mixing chamber length, the supply diameter of the liquid fuel and gas, and the exit orifice diameter. In addition, because of the use of a twin-fluid, optimized data is required depending on the spray condition. In this study, spray experiment was carried out under the pressure condition of 7 bar or more, which is the spraying condition used in industry. There was no change in flow rate with the length of the Y-jet nozzle mixing chamber, but the difference in SMD was confirmed. Adjusting the exit orifice diameter is most important to achieve the desired flow rate. Changes in the liquid and gas inlet port diameters ratio were found to be help improve the operating range and significant difference in SMD was observed.

• Journal of ILASS-Korea
• /
• v.11 no.2
• /
• pp.59-68
• /
• 2006

Experimental results of the metal powder production with internal mixing, internal impinging and the atomizer coupled with substrate design are presented in this paper. In a test with internal mixing atomizer, mean powder size was decreased from $37{\mu}m\;to\;23{\mu}m$ for Pb65Sn35 alloy as the gas-to-melt mass ratio was increased from 0.04 to 0.17. The particle size further reduces to $16.01{\mu}m$ as the orifice area is increased to $24mm^2$. The micrograph of the metal powder indicates that very fine and spherical metal powder has been produced by this process. In a test program using the internal impinging atomizers, the mean particle size of the metal powder was decreased from $22{\mu}m\;to\;12{\mu}m$ as the gas-to-melt-mass ratio increased from 0.05 to 0.22. The test results of an atomizer coupled with a substrate indicates that the deposition rate of the molten spray on the substrate is controlled by the diameter of the substrate, the height of the substrate ring and the distance of the substrate from the outlet of the atomizer. This in rum determines the powder production rate of the spraying processes. Experimental results indicate that the deposition rate of the spray forming material decreases as the distance between the substrate and the atomizer increases. For example, the deposition rate decreases from 48% to 19% as the substrate is placed at a distance from 20cm to 40cm. On the other hand, the metal powder production rate and its particle size increases as the subsrate is placed far away from the atomizer. The production of metal powder with mean particle size as low as $3.13{\mu}m$ has been achieved, a level which is not achievable by the conventional gas atomization processes.

• Korean Journal of Plant Tissue Culture
• /
• v.28 no.5
• /
• pp.273-276
• /
• 2001

In order to develop effective acclimatization methods for Aralia elata plantlets regenerated from somatic embryos, various acclimatizing conditions were compared regarding both survival rate and growth of the plantlets. The plantlets were transplanted into plastic boxes containing artificial soil in the presence of either several levels of MS liquid media, distilled water, 2% sucrose or 0.1% hyponex solution. They were then cultured by spraying of distilled water twice a week and maintained in the normal tissue culture room. Perlite was proved to be better than vermiculite on survival rate and growth of the plantlets. As the size of perlite (larger than 0.2 cm in diameter) increased, both the survival rate and growth of the plantlets improved. Among the various MS liquid media and different aqueous solutions tested, distilled water appeared to result in the best survival rate and growth. MS media were also effective in increasing survival rate and supporting growth when diluted to 1/4 and/or 1/8. The acclimatized plantlets could be transplanted directly onto the nursery bed and grown normally. The above results suggest that plantlets regenerated from somatic embryos of Aralia elata be effectively acclimatized using a plastic box containing perlite with distilled water treatment.

• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.469-474
• /
• 2001

Milling the rice with low moisture requires more energy, produces more cracked rice, and results in reducing taste of cooked rice. Accordingly, it is necessary to add moisture to the rice with low moisture to obtain optimum moisture level for milling and taste of rice. This study was performed to evaluate the influence of initial moisture content and absorption rate on rice crack, milling energy and whiteness of milled rice and to obtain the information for design of rewetting system mounted on stirring device in grain bin. The tests were conducted for the four levels of initial moisture content in the range of 11.4 to 14.5%(w.b.) and six levels of absorption rate in the range of 0.04 to 1.0%, w.b./hr. In the case of lower moisture content below 12%(w.b.), crack ratios of brown rice were remarkably high regardless of initial moisture contents. Therefore, it was found that rough rice below 12%(w.b.) in initial moisture content could not rewetted by spraying water without crack generation of low level. Absorption rate must be below 0.3%, w.b./hr to maintain crack ratio increase of less than 1% regardless of initial moisture contents. In the case of allowable crack ratio increase of 2% and 5%, it was found that the maximum absorprion rate was respectively 0.6%, w.b./hr and 1.0%, w.b./hr in the initial moisture content of above 13.5%(w.b.). Rewetting the rough rice in moisture content of 11.4 to 14.5%(w.b.) to 14.3 to 16.9%(w.b.) decreased milling energy consumption by 15.9 to 22.3%. The effect of energy saving was higher in the samples of higher initial moisture content. Whiteness of milled rice was decreased by 0.5 to 1.5.

• Journal of Korean Society of Forest Science
• /
• v.87 no.2
• /
• pp.308-315
• /
• 1998

This study was conducted to evaluate the availability of the forest topsoil as a source of the "Native-soil(seed-fertilizer-soil materials)" for the hydroseeding measures which are environmentally and ecologically stable revegetation measures on rock cut-slopes. Soil sampling and factorial experiments were used with a split plot design(main plot : forest soil type and soil spraying thickness, subplot : seeding rate) in 1996. Results obtained in this study were summarized as follows : Because of the competition between the seeded(introduced) species and the native species, the number of naturally emerged species in the non-seeded plot and that of in the seeded plot were $5{\sim}9species/0.07m^2$ and $2{\sim}6species/0.07m^2$, respectively. As increasing the seeding rate(introduced species), the appearance ratio of naturally emerged species was decreased. The total number of individuals was high in the plot which used coniferous forest soil as a seed source, however the ratio of the individuals of naturally emerged species was high(30%) in the plot which used deciduous forest soil. The usage of the forest topsoil as seed bank source onto the "Native-soil" materials for hydroseeding could be reduce the seeding rate to $1,000seedlings/m^2$. According to the several factors which are competition between seeded species and naturally emerged species, dryness of soil materials, and seed burial, spraying thickness with more than 5cm was suitable for the growth of plants in variety.

• The Korean Journal of Pesticide Science
• /
• v.11 no.4
• /
• pp.299-304
• /
• 2007

Surveying, laboratory and field trial were performed to elucidate the causes of non-spinning syndrome of silkworm, Bombyx mori, abnormal symptoms of silkworm instars observed in certain sericultural fanning region. Mortality and growth of silkworm was still influenced by feeding the mulberry leaves sprayed with 10,000 fold diluted solution of standard spray of diflubenzuron WP (25%). Mortality and growth of silkworm fed with diflubenzuron-sprayed mulberry leaves with recommended spray solution were entirely affected even six weeks after spraying irrespective to the instars. Larval period of 5th instar and cocooning duration of silkworm was not affected in case 50m of buffer zone has maintained in near-by orchard field sprayed with diflubenzuron WP (25%). However, survival rate of pupae was not influenced in case 100 m of buffer zone has kept. Insect growth regulating insecticides were required to keep a certain distance of buffer zone when sprayed with water-diluted solution, 100 m from the application site at least in order to prevent contamination of the spraying drift by the chemicals.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.29 no.3
• /
• pp.285-290
• /
• 1984

The effects of retardants B995 and CCC on the growth and yield of soybean cultivar, kwanggyo, were investigated. The 3 application times(4th, 5th and 6th trifoliate leaf stage) combined with 4 concentrations (500, 1000, 2000 and 3000 ppm) were treated, and the retardant solutions were sprayed on the foliage. Only stem length in retardants, rate of podding in application times, and, in concentrations, stem length, number of branch, number of pod per plant and grain yield, were significant. In the inhibition of stem elongation, B995 was more effective than CCC, and rate of podding was the highest in the 4th leaf-spraying. The highest concentration, 3000 ppm, was the most effective in the inhibition of stem elongation and in the increase of number of branch and pod, rate of podding, and in yield. The number of node of mainstem, dry stem weight, chlorophyll and 100 grain weight were not significant with any treat. Yield had positively correlated with number of branch and pod, and rate of podding but negatively with stem length. The retardants was thought to be considerably conducive to the increase of yield.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.2
• /
• pp.121-135
• /
• 2016

The present study is an analysis of the monitoring results of the four areas that underwent the experimental construction of Straw-net+seedspray, Vegetation media spray method(t=2cm), and Vegetation media spray method(t=3cm), with the purpose of selecting the adequate revegetation of cutting slopes in weathered granite soil. Cutting slopes are mostly designed in the Straw-net+seedspray method, but since weathered granite soil slopes tend to have an infertile soil quality that runs down, it is difficult for seed germination and growth. It is difficult to apply Straw-net+seedspray to weathered granite soil slopes considering the germination rate and coverage rate of the Straw-net+seedspray method, which accompanies erosion and scouring. The final conclusions are summarized as follows. First, Straw-net+seedspray has difficulty recruiting plants to infertile weathered granite soil, which results in a lower coverage rate and fewer species, so it is not adequate construction method. Second, Vegetation spraying methods with wet media are more advantageous in early revegetation. The wet construction methods are faster than the dry construction methods in terms of early germination and its early growth are more excellent. Third, when constructing Vegetation spray methods with dry media, it were more advantageous if the thickness was thicker. When the soil-media is thicker, the soil is resilient to droughts, so the thickness must be flexibly applied according to the soil quality and slant of the weathered granite soil slope. The present study is a monitoring result for some areas of Gangwon-do, so its results may differ from other areas.