• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.7
• /
• pp.503-509
• /
• 2015

Based on ISO 7235, an experimental setup to measure the acoustic performance of splitter type dissipative silencers was fabricated. The length of each duct, sound source, microphone locations, modal filter, and anechoic termination were considered in the design of this setup. The modal filter is a particularly important factor because it affects the limit of measurement. The effects of number of splitters, absorptive material density, perforate plate, and media on the noise reduction of the sample silencers were experimentally investigated. The experimental results show that the insertion loss of a silencer with media, high perforate opening, and higher number of splitters increases especially at higher frequencies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.11
• /
• pp.883-891
• /
• 2018

In this paper, aerodynamic noise simulation was conducted using DES (Detached Eddy Simulation) and FW-H (Ffowcs Williams and Hawkings) acoustic analogy for the tandem cylinders which have configuration similar to a landing gear of airplanes. Numerical simulation for the tandem cylinders whose centers are 3.7D apart was carried out and results were compared with the measured data such as flow characteristics, pressure coefficients on the cylinder surfaces and far-field noise characteristics. It was confirmed that periodically shedded vortices released at the upstream cylinder and impinged on the downstream cylinder surface are major sources of aerodynamic noise. After verifying the computational method of using DES and FW-H acoustic analogy for predicting aerodynamic noise of tandem cylinders, additional simulation was conducted to examine the effect of attaching a splitter plate at the rear of the upstream cylinder. It was confirmed that the noise level in specific frequency band decreased significantly because the splitter plate changed the vortex shedding features and reduced dipole noise source.

• Wind and Structures
• /
• v.11 no.5
• /
• pp.377-389
• /
• 2008

An experimental investigation has been conducted to determine the effectiveness of base shield plates in reducing the drag of a rough circular cylinder in a cross flow at Reynolds numbers in the range $3{\times}10^4{\leq}Re{\leq}10.5{\times}10^4$. Three model configurations were investigated and compared: a plane cylinder (PC), a cylinder with a splitter plate (MC1) and a cylinder fitted with base shield plates (MC2). Each configuration was studied in the sub and supercritical flow regimes. The chord of the plates, L, ranged from 0.22 to 1.50D and the cavity width, G, between the plates was in the range from 0 to 0.93D. It is recognized that base shield plates can be employed more effectively than splitter plates to reduce the aerodynamic drag of circular cylinders in both the sub- and supercritical flow regimes. For subcritical flow regime, one can get 53% and 24% drag reductions for the MC2 and MC1 models with L/D=1.0, respectively, compared with the PC model. For supercritical flow regime however, the corresponding drag reductions are 38% and 7%.

• Korean Journal of Optics and Photonics
• /
• v.6 no.2
• /
• pp.130-134
• /
• 1995

A small signal gain coefficient of Nd:glass was measured and a cavity-dumped laser was constructed. To measure the small signal gain coefficient, we constructed a resonator consisting of Nd:glass, Pockels cell, polarizing beam splitter. The measured small signal gain coefficient was $0.088 cm_{-1}$ when the input energy was 100 J and the round-trip internal loss of the resonator was 56%. The cavity-dumped laser was constructed using Nd:glass. 2 m radius of curvature HR-mirrors, Pockels cell, polarizinig beam splitter and $\lambda/4$ plate. The output energy of cavity-dumped laser was 0.85 J at 140 J input energy and the laser pulse width was 8 ns.s 8 ns.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.120-127
• /
• 2000

This study is concerned with evaluating the effects of acoustic excitation on the development of two stream mixing layer generated by split plate. The ratios of two velocities U1 and U2 either side of the splitter plate were such that $U_1/U_2$=1.0 (uniform flow) or $U_1/U_2$<1.0(shear flow). The mixing layers were disturbed acoustically through the edge of split plate. Quantitative data were obtained with hot-wire anemometry. Flow visualization with smoke-wire was also employed for qualitative study. the results show that the large scale structures of mixing layers are strongly affected by excitation frequency and amplitude in both uniform and shear flows. The maximum streamwise and vertical turbulent intensities of the excited flow fields are apt to be decreased as compared with those of without excitation. The flow characteristics of uniform flow are more influenced by acoustic excitation than those of shear flow.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.54-61
• /
• 1997

In this paper, a new holographic display system that can in real-time reconstruct the complex hologram without the bias and the conjugate image, which is obtained form the modified triangular interferometer, is presented. The proposed system is made of adding liquid crystal displays(LCDs), a $\lambda$/2 wave plate, and a polarizing beam splitter to the conventional mach-zehnder interferontric configuration. We demonstrate through theoretical analysis and experiment that real-time image reconstruction from the complex hologram is possible using the proposed system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.1
• /
• pp.160-164
• /
• 2005

The process of recognizing a vehicle involves detection of the vehicle, recognition of the vehicle model, and identification of the vehicle. The process of vehicle identification involves identification of the vehicle itself, such as by recognition of the license plate on the vehicle. In this paper the method involves the use of a beam splitter to divide incident rays into two directions, a transmitted beam and a reflected beam of different light intensities, and synthesizing two captured images using CCD devices from each beam, thus producing fluctuation-free images of a wide dynamic range even when the subject is moving. A prototype license plate recognition system was also developed using the experimental sensing device. The system achieved a 98.7% recognition rate on 466 images of moving vehicles, which demonstrates its effectiveness as a license plate recognition system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.6
• /
• pp.722-733
• /
• 1999

The wall pressure fluctuations of a turbulent boundary layer over a flat plate have been investigated in an anechoic wind tunnel facility. The anechoic wind tunnel consists of acoustically-lined duct, muffler, and splitter-type silencer for noise suppression and vanes for reducing head losses involved. To improve spectra characteristics in high frequency range, a 1/8" pressure-type microphone sensor, which has a pin-holed cap of various diameters, was employed in this experiment. It was shown that the pin-holed microphone sensor with a dimensionless diameter $d^+$ of 7.1 resolved the high frequency pressure fluctuations most effectively among ones with various pin-hole diameters. The measured wall pressure spectra in terms of three types of scaling parameters were in good agreement with other experimental and numerical results. The pressure events of high amplitude were found to contribute to total fluctuating pressure energies in the turbulent boundary layer significantly and supposed to radiate to the far-field effectively.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1526-1531
• /
• 2007

Data transmission capacity that is required in 2010 is forecasted that increase by optical communication capacity more than present centuple, and is doing increased demand of optical communication related industry product present. Specially, Lid glass' application that is one of optical communication parts is used in optical communication parts manufacture of Fiber array, Ferrule array, Fanout Black, Silica optical waveguide chip and splitter etc. Also, it is used widely for communication network system, CATV, ATM-PON, FTTH and system. But, Lid glass need much processing times and becomes cause in rising prices of optical communication parts because production cost is expensive. The objectives, of this work is to suggest the micro concave and convex pattern manufacturing technology on borosilicate plate using high temperature and compression molding method. As a result, could developed micro pattern Mold more than 5 pattern, and reduce Lid Glass manufacture cycle time.

• Wind and Structures
• /
• v.4 no.2
• /
• pp.85-100
• /
• 2001

The mechanism of wind-induced ovalling vibrations of cylindrical shells is numerically investigated by using a vortex method. The subject of this paper is limited to a two-dimensional structure in the subcritical regime. The aerodynamic stability of the ovalling vibrations in the second to fourth circumferential modes is discussed, based on the results of a forced-vibration test. In the analysis, two modal configurations are considered; one is symmetric and the other is anti-symmetric with respect to a diameter parallel to the flow direction. The unsteady pressures acting on a vibrating cylinder are simulated and the work done by them for one cycle of a harmonic motion is computed. The effects of a splitter plate on the flow around the cylinder as well as on the aerodynamic stability of the ovalling vibrations are also discussed. The consideration on the mechanism of ovalling vibrations is verified by the results of a free-vibration test.