• 한국소음진동공학회논문집
• /
• 제25권7호
• /
• pp.503-509
• /
• 2015

Based on ISO 7235, an experimental setup to measure the acoustic performance of splitter type dissipative silencers was fabricated. The length of each duct, sound source, microphone locations, modal filter, and anechoic termination were considered in the design of this setup. The modal filter is a particularly important factor because it affects the limit of measurement. The effects of number of splitters, absorptive material density, perforate plate, and media on the noise reduction of the sample silencers were experimentally investigated. The experimental results show that the insertion loss of a silencer with media, high perforate opening, and higher number of splitters increases especially at higher frequencies.

• 한국항공우주학회지
• /
• 제46권11호
• /
• pp.883-891
• /
• 2018

본 연구에서는 항공기 랜딩 기어와 유사한 형태의 탠덤 실린더에 대해 DES (Detached Eddy Simulation)와 FW-H (Ffowcs Williams and Hawkings) 음향상사법을 이용한 전산공력 소음해석을 수행하였다. 실린더 중심 간 거리 3.7D 조건에 대한 전산공력소음해석 결과를 탠덤 실린더를 지나는 외부 유동 특성 및 원거리 소음을 계측한 선행 연구 결과와 비교하였다. 전방 실린더의 상/하부에서 발생한 와류(Vortex)가 특징적인 주파수를 갖고 후방 실린더에 충돌하면서 소음 발생원이 되는 것을 확인하였다. DES 와 FW-H 음향상사법을 이용한 전산공력소음해석 방법의 타당성을 확인한 후, 전방 실린더의 후방에 분할판을 적용한 경우의 전산공력소음해석을 수행하였다. 전방 실린더의 후방에 분할판이 적용되면 전방 실린더의 상/하부에서 발생하는 와류의 특징을 변화시키고 이극자 소음원 크기를 감소시켜 특정 주파수 대역에서 발생하는 소음 크기가 감소하는 것을 확인하였다.

• Wind and Structures
• /
• 제11권5호
• /
• pp.377-389
• /
• 2008

An experimental investigation has been conducted to determine the effectiveness of base shield plates in reducing the drag of a rough circular cylinder in a cross flow at Reynolds numbers in the range $3{\times}10^4{\leq}Re{\leq}10.5{\times}10^4$. Three model configurations were investigated and compared: a plane cylinder (PC), a cylinder with a splitter plate (MC1) and a cylinder fitted with base shield plates (MC2). Each configuration was studied in the sub and supercritical flow regimes. The chord of the plates, L, ranged from 0.22 to 1.50D and the cavity width, G, between the plates was in the range from 0 to 0.93D. It is recognized that base shield plates can be employed more effectively than splitter plates to reduce the aerodynamic drag of circular cylinders in both the sub- and supercritical flow regimes. For subcritical flow regime, one can get 53% and 24% drag reductions for the MC2 and MC1 models with L/D=1.0, respectively, compared with the PC model. For supercritical flow regime however, the corresponding drag reductions are 38% and 7%.

• 한국광학회지
• /
• 제6권2호
• /
• pp.130-134
• /
• 1995

이득 선폭이 넓고 가공이 쉬원 고출력 제이저의 증폭 이득 매질로 유리한 Nd:glass 이득 매질의 소신호 이득 계수를 측정하고 이 Nd:glass를 이용하여 제작한 cavity-dumping형 레이저의 출력 특성을 조사하였다. 소신호 이득 계수를 측정하기 위해 Nd:glass, Pockels cell, 편광분할기 등을 포함하는 공진기를 구성하였으며, 측정된 소신호 이극 계수는 전기 입력 에너지가 100J일 때 $0.088 cm_{-1}$ 공진기의 왕복 내부 손실은 56%였다. Cavity-dumping형 레이저 공진기는 곡률반경이 2m인 두개의 전반사경과 Nd:glass, Pickels cell, 편광분할기, $\lambda/4$ plate 등으로 구성되었으며 제작된 레이저의 출력 에너지는 전기 입력 에너지가 140J일 때, 최대 0.85J이었고 출력 레이저 펄스폭은 8ns였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.120-127
• /
• 2000

This study is concerned with evaluating the effects of acoustic excitation on the development of two stream mixing layer generated by split plate. The ratios of two velocities U1 and U2 either side of the splitter plate were such that $U_1/U_2$=1.0 (uniform flow) or $U_1/U_2$<1.0(shear flow). The mixing layers were disturbed acoustically through the edge of split plate. Quantitative data were obtained with hot-wire anemometry. Flow visualization with smoke-wire was also employed for qualitative study. the results show that the large scale structures of mixing layers are strongly affected by excitation frequency and amplitude in both uniform and shear flows. The maximum streamwise and vertical turbulent intensities of the excited flow fields are apt to be decreased as compared with those of without excitation. The flow characteristics of uniform flow are more influenced by acoustic excitation than those of shear flow.

• 전자공학회논문지D
• /
• 제34D권4호
• /
• pp.54-61
• /
• 1997

In this paper, a new holographic display system that can in real-time reconstruct the complex hologram without the bias and the conjugate image, which is obtained form the modified triangular interferometer, is presented. The proposed system is made of adding liquid crystal displays(LCDs), a $\lambda$/2 wave plate, and a polarizing beam splitter to the conventional mach-zehnder interferontric configuration. We demonstrate through theoretical analysis and experiment that real-time image reconstruction from the complex hologram is possible using the proposed system.

• 한국정보통신학회논문지
• /
• 제9권1호
• /
• pp.160-164
• /
• 2005

자동차 번호판 자동인식에서 어두운 조명에서나 날씨가 좋지 않을 경ㅇ 차량의 형상이 왜곡 될 수 있고, 번호판을 식별하는데 어려움이 있다. 이에 본 논문에서는 움직이는 차량의 영상에서 흔들림이 없고, 밝은 햇빛에서 어두운 조명상태까지의 다양한 환경을 수용할 수 있는 자동차 번호판 인식방법을 제안하였다. 제안한 방법은 투시광선을 서로 다른 세기를 갖는 두 개의 빔(beam)으로 분리한 다음 CCD 카메라를 사용하여 두 개의 포착된 이미지를 조합하여 물체가 움직일 때도 동요 없는 이미지를 산출하였다. 실험결과로써 466 개의 움직이는 차량영상을 이용한 결과 98.7%의 인식률을 얻을 수 있었다.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.722-733
• /
• 1999

The wall pressure fluctuations of a turbulent boundary layer over a flat plate have been investigated in an anechoic wind tunnel facility. The anechoic wind tunnel consists of acoustically-lined duct, muffler, and splitter-type silencer for noise suppression and vanes for reducing head losses involved. To improve spectra characteristics in high frequency range, a 1/8" pressure-type microphone sensor, which has a pin-holed cap of various diameters, was employed in this experiment. It was shown that the pin-holed microphone sensor with a dimensionless diameter $d^+$ of 7.1 resolved the high frequency pressure fluctuations most effectively among ones with various pin-hole diameters. The measured wall pressure spectra in terms of three types of scaling parameters were in good agreement with other experimental and numerical results. The pressure events of high amplitude were found to contribute to total fluctuating pressure energies in the turbulent boundary layer significantly and supposed to radiate to the far-field effectively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1526-1531
• /
• 2007

Data transmission capacity that is required in 2010 is forecasted that increase by optical communication capacity more than present centuple, and is doing increased demand of optical communication related industry product present. Specially, Lid glass' application that is one of optical communication parts is used in optical communication parts manufacture of Fiber array, Ferrule array, Fanout Black, Silica optical waveguide chip and splitter etc. Also, it is used widely for communication network system, CATV, ATM-PON, FTTH and system. But, Lid glass need much processing times and becomes cause in rising prices of optical communication parts because production cost is expensive. The objectives, of this work is to suggest the micro concave and convex pattern manufacturing technology on borosilicate plate using high temperature and compression molding method. As a result, could developed micro pattern Mold more than 5 pattern, and reduce Lid Glass manufacture cycle time.

• Wind and Structures
• /
• 제4권2호
• /
• pp.85-100
• /
• 2001

The mechanism of wind-induced ovalling vibrations of cylindrical shells is numerically investigated by using a vortex method. The subject of this paper is limited to a two-dimensional structure in the subcritical regime. The aerodynamic stability of the ovalling vibrations in the second to fourth circumferential modes is discussed, based on the results of a forced-vibration test. In the analysis, two modal configurations are considered; one is symmetric and the other is anti-symmetric with respect to a diameter parallel to the flow direction. The unsteady pressures acting on a vibrating cylinder are simulated and the work done by them for one cycle of a harmonic motion is computed. The effects of a splitter plate on the flow around the cylinder as well as on the aerodynamic stability of the ovalling vibrations are also discussed. The consideration on the mechanism of ovalling vibrations is verified by the results of a free-vibration test.