• 수산해양기술연구
• /
• 제50권4호
• /
• pp.427-434
• /
• 2014

Although ex situ target strength (TS) measurements using dual- and split-beam systems have become the primary approach of estimating fish abundance, theoretical model estimation is a powerful tool for verifying the measurements, as well as for providing values when making direct measurements is difficult. TS values for 20 samples of live bambooleaf wrasse (Pseudolabrus japonicus) whose target length (TL) ranged between 13.7 and 21.3 cm were estimated theoretically using the Kirchhoff-ray mode model, and the TS values for 18 live fish samples were additionally measured at ${\sim}0^{\circ}$ tilt angle to the swimming aspect using a tethered method at a frequency of 120 kHz to verify the theoretical values. The digitizing intervals used to extract the fish body and swim bladder morphology in the X-ray photographs significantly affected the calculated TS patterns, but variations based on the speed of sound and density ratio values for the general range of fish flesh were relatively small (within 1 dB). Close agreement was observed between the measured and theoretical TS values, and the correlation between the average TS and body length of the fish could be calculated accurately as <$TS_{120kHz}$>= 20logTL (cm) -71.6 using the theoretical method.

• Advances in concrete construction
• /
• 제6권1호
• /
• pp.29-45
• /
• 2018

This paper investigates the effect of inclusion of glass fibers on mechanical and fracture properties of binary blend geopolymer concrete produced by using fly ash and ground granulated blast furnace slag. To study the effect of glass fibers, the mix design parameters like binder content, alkaline solution/binder ratio, sodium hydroxide concentration and aggregate grading were kept constant. Four different volume fractions (0.1%, 0.2%, 0.3% and 0.4%) and two different lengths (6 mm, 13 mm) of glass fibers were considered in the present study. Three different notch-depth ratios (0.1, 0.2, and 0.3) were considered for determining the fracture properties. The test results indicated that the addition of glass fibers improved the flexural strength, split tensile strength, fracture energy, critical stress intensity factor and critical crack mouth opening displacement of geopolymer concrete. 13 mm fibers are found to be more effective than 6 mm fibers and the optimum dosage of glass fibers was found to be 0.3% (by volume of concrete). The study shows the enormous potential of glass fiber reinforced geopolymer concrete in structural applications.

• Advances in concrete construction
• /
• 제9권6호
• /
• pp.589-596
• /
• 2020

In an effort to find alternate, environment friendly and sustainable building materials, the scope of possible utilization of iron slag (I-sand), generated as a by-product in iron and steel industries, as fine aggregates in reinforced cement concrete (RCC) made with manufactured sand (M-sand) is examined in this manuscript. Systematic investigations of the physical, mechanical, microstructural and durability properties of I-sand in comparison with RCC made with M-sand have been carried out on various mix designs prepared by the partial/full replacement of I-sand in M-sand. The experimental results clearly indicate the possibility of utilizing iron slag for preparing RCC in constructions without compromising on the property of concrete, durability and performance. This provides an alternate possibility for the effective utilization of industrial waste, which is normally disposed by delivering to landfills, in building materials which can reduce the adverse environmental effects caused by indiscriminate sand mining being carried out to meet the growing demands from construction industry and also provide an economically viable alternative by reducing the cost of concrete production.

• Advances in concrete construction
• /
• 제8권4호
• /
• pp.321-333
• /
• 2019

The present study targets to access the consequence of utilization of coarse aggregates retrieved from waste concrete as a substitution of coarse fraction of natural aggregates and silica nano-particles as partial substitution of cement using principles of factorial design. Furthermore, procedures of design of experiments are employed to examine the effect of use of recycled aggregates and nano-silica. In this investigation, compressive strength found after at 7, 28, 90 and 365 days, split and flexural tensile strength, ultrasonic pulse velocity and rebound number and are chosen as responses, whereas the percentages of recycled coarse aggregates (RCA%) and nano-silica (NS(%)) are selected as factors. Analysis of Variance has been conducted on the experimental results for the selected responses with consideration the both factors, which indicates that RCA (%) and NS (%) have substantial impact on the various responses. However, the present analysis depicts that interaction between factors has considerable effect on the chosen parameters of concrete. Furthermore, validation experiments are carried to validate these models for compressive and tensile strength for 100% RCA and 1% NS. The results of comparative study indicates that that the error of the estimation determined using the relevant models are found to be small (±5%) in comparison with the analogous experimental results, which authenticates the calculated models.

• 한국농공학회논문집
• /
• 제49권4호
• /
• pp.63-70
• /
• 2007

The soil samples used in this study were prepared with the residual granite soils passed through the #4 sieve and obtained from Pocheon in Gyeonggi-Ki do. Specifically, five types of samples were prepared. Sample A which is a natural state soil was classified as SM according to the uses. Samples of B, C, D, and E were prepared by mixing Sample A with bentonite and were classified as SC according to the uses. The plasticity indexes of samples B, C, D, and E were 15, 25, 30, and 40, respectively. The specimens, whose dimensions are 100mm by 127.5mm, were prepared by A method of ASTM D 698 with the Proctor mold. In experiments, the loading with the 1%/min was applied. Four different disk diameters, 13mm, 26mm, 38mm, and 52mm were used in the Improved Unconfined Penetration (IUP) tests. To compare the tensile strengths, the split tensile tests were also conducted on the same specimens used for the IUP tests. To find out the effects of moisture contents, plasticity Index of specimens on the tensile strength, six different water contents were used for making a specimen.

• Computers and Concrete
• /
• 제15권2호
• /
• pp.215-229
• /
• 2015

The emerging technology of self compacting concrete, fiber reinforcement together reduces vibration and substitute conventional reinforcement which help in improving the economic efficiency of the construction. The objective of this work is to find the regression model to determine the response surface of mix proportioning Steel Fiber Reinforced Self Compacting Concrete (SFSCC) using statistical investigation. A total of 30 mixtures were designed and analyzed based on Design of Experiment (DOE). The fresh properties of SCC and mechanical properties of concrete were studied using Response Surface Methodology (RSM). The results were analyzed by limited proportion of fly ash, fiber, volume combination ratio of two steel fibers with aspect ratio of 50/35: 60/30 and super plasticizer (SP) dosage. The center composite designs (CCD) have selected to produce the response in quadratic equation. The model responses included in the primary stage were flowing ability, filling ability, passing ability and segregation index whereas in harden stage of concrete, compressive strength, split tensile strength and flexural strength at 28 days were tested. In this paper, the regression model and the response surface plots have been discussed, and optimal results were found for all the responses.

• Composites Research
• /
• 제18권1호
• /
• pp.45-54
• /
• 2005

필라멘트 와인딩 공정으로 제작된 고속 회전용 복합재 플라이휠 로터는 층간분리 현상에 의해 에너지 저장용량이 저하된다. 그리고 기존의 링 타입 허브는 복합재 로터 내측면에 인장력을 가하게 되고. 이는 로터내의 반경방향 인장응력을 가중시켜 로터의 한계 회전수를 저하시킨다. 복합재 로터의 응력해석을 위해서 2차원 평형방정식과 경계조건이 사용되었고, 이를 근거로 강도비를 최소화시키는 최적의 내압이 존재함을 수치적으로 제시하였다. 이러한 최적의 내압을 발생시키기 위해서 원주방향으로 분할된 스플릿 타입 허브를 제안하고, 링 타입과 스플릿 타입 허브의 두께변화에 따른 내압분포의 영향을 제시하였다. 스플릿 타입 허브의 유효성을 검증하기 위해 허브를 포함한 복합재 로터를 제작한 다음, 최대 회전수 40,000rpm까지 파손 없이 스핀 테스트를 수행하였다. 동시에 로터 표면에 4개의 원주방향 및 반경방향 스트레인게이지를 부착하여 변형률을 무선으로 측정하였다. 측정된 변형률은 해석결과와 매우 잘 일치하였다. 특히 반경방향의 응력을 크게 낮출 수 있었고, 반경방향으로 모두 압축 변형률이 발생함을 확인하였다. 결국 스플릿 타입 허브는 플라이휠 로터의 단점인 반경방향의 낮은 강도를 보안하는 효과를 나타내어, 저장에너지 밀도를 증가시킴으로써 대형 고출력 플라이횔 에너지 저장 시스템의 개발 가능성을 제시하였다.

• Advances in concrete construction
• /
• 제9권2호
• /
• pp.207-215
• /
• 2020

This paper describes the experimental studies carried out to determine the properties of fresh and hardened concrete with Recycled Plastic Waste (RPW) as a partial replacement material for fine aggregates. In the experimental study, RPW was used for replacing river sand and manufactured sand (M sand) aggregates in concrete. The replacement level of fine aggregates was ranging from 5% to 20% by volume with an increment of 5%. M40 grade of concrete with water cement ratio of 0.40 was used in this study. Two different types of RPW were used, and they are (i) un-activated RPW and (ii) activated RPW. The activated RPW was obtained by alkali activation of un-activated RPW using NaOH solution. The hardened properties of the concrete determined were dry density, compressive strength, split tensile strength, flexural strength and ultrasonic pulse velocity (UPV). The properties of the concrete with river sand, M sand, activated RPW and un-activated RPW were compared and inferences were drawn. The effect of activation using NaOH solution was investigated using FT-IR study. The micro structural examination of hardened concrete was carried out using Scanning Electron Microscopy (SEM). The test results show that the strength of concrete with activated RPW was more than that of un-activated RPW. From the results, it is evident that it is feasible to use 5% un-activated RPW and 15% activated RPW as fine aggregates for making concrete without affecting the strength properties.

• Advances in concrete construction
• /
• 제14권5호
• /
• pp.355-368
• /
• 2022

This paper investigates the impact of length and volume fractions (VFs) of banana fibres (BFs) on the mechanical and physical properties of concrete. The mechanical properties were compressive strength, splitting tensile, flexural strength, and bond stress, while the physical properties were unit weight and absorption. The slump test was used to determine workability. The concrete's behaviour with BFs was studied using scanning electron microscopy. Experimental work of concrete mixtures with BFs of various lengths (12 mm, 25 mm, and 35 mm) and VFs (0%, 0.5%, 1.0%, and 1.5%) were carried out. The samples did not indicate any agglomeration of fibres or heterogeneity during mixing. The addition of BFs to concrete with VFs of up to 1.50% for all fibre lengths have a significant impact on mechanical properties, also the longer fibres performed better than shorter ones at all volume fractions of BFs. The mix10, which contain BFs with VFs 1.5% and length 35 mm, demonstrated the highest mechanical properties. The compressive strength, splitting tensile, flexural strength, and bond stress of the mix10 were 37.71 MPa, 4.27 Mpa, 6.12 MPa, and 6.75 MPa, an increase of 7.37%, 20.96%, 24.13%, and 11.2% over the reference concrete, which was 35.12 MPa, 3.53 MPa, 4.93 MPa, and 6.07 MP, respectively. The absorption is increased for all lengths by increasing the VFs up to 1.5%. Longer fibres have lower absorption, while shorter fibres have higher absorption. The mix8 had the highest absorption of 4.52%, compared to 3.12% for the control mix. Furthermore, the microstructure of concrete was improved through improved bonding between the fibres and the matrix, which resulted in improved mechanical properties of the composite.

• Computers and Concrete
• /
• 제21권3호
• /
• pp.249-259
• /
• 2018

The use of recycled aggregate in concrete is gaining much attention due to the growing need for sustainability in construction. In the present study, Self Compacting Concrete (SCC) is made using both natural and recycled aggregate (crushed recycled concrete aggregate from building demolished waste) and performance of recycled aggregate based SCC for the bond behaviour of reinforcement is evaluated. The major factors that influence the bond like concrete compressive strength (Mix-A, B and C), diameter of bar ($D_b=10$, 12 and 16 mm) and embedment length of bar ($L_d=2.5Db$, $5D_b$ and full depth of specimen) are the parameters considered in the present study in addition to type of aggregates (natural and recycled aggregates). The mix proportions of Natural Aggregate SCC (NASCC) are arrived based on the specifications of IS 10262. The mix proportions also satisfy the guidelines of EFNARC. In case of Recycled Aggregate SCC (RASCC), both the natural coarse and fine aggregates are replaced 100% by volume with that of recycled aggregates. These mixes are also evaluated for fresh properties as per EFNARC. The hardened properties like compressive strength, split tensile strength and flexural strength are also determined. The pull-out test is conducted as per the specifications of IS 2770 (Part-1) for determining the bond strength of reinforcement. Bond stress versus slip curves were plotted and a typical comparison of RASCC is made with NASCC. The fracture energy i.e., area under the bond stress slip curve is determined. With the use of recycled aggregates, reduction in maximum bond stress is noticed whereas, the normalised maximum bond stress is higher in case of recycled aggregates. Based on the experimental results, regression analysis is conducted and an equation is proposed to predict the maximum bond stress of RASCC. The equation is in good agreement with the experimental results. The available models in the literature are made use to predict the maximum bond stress and compare the present results.