• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.355-361
• /
• 2008

In highly stressed machine elements such as angular contact ball bearings and toroidal type traction drives, the elastohydrodynamic lubrication of elliptical contacts with both rolling and spinning motion are occur. In this paper, a finite difference method with non-uniform grid systems and the Newton-Raphson method are applied to solve the problems. Pressure distributions, film contours and variations of the minimum and central film thicknesses are compared with various ellipticity parameter, dimensionless speed and load parameter. The results showed that the spinning motion has significant influence especially on the film shapes. Reduction of the minimum film thickness under spinning is remarkable whereas the central film thickness is relatively less. Especially variations of the minimum film thicknesses with rolling velocity, load and ellipticity ratio are a great different from those of pure rolling. Therefore present numerical scheme can be used in the analysis of general elliptical contact EHL problems and further studies are required.

• 소음진동
• /
• 제7권2호
• /
• pp.261-272
• /
• 1997

Recently washing machines are to be in lower vibration and lower sound because of better environment. Vibration problems in washing machines occur in both washing mode and spinning mode, but vibration in spinning mode becomes main problem because of its high rotating speed and continuity. Vibration while spinning is mainly due to rigid body motion of total washing system which includes suspending rods, washing bath, spinning bath, and gear sets. In this study, some researches were done in order to analyze the rigid body motion of washing system and flexible vibration of spinning bath. A basic mathematical model was established, and the effect of position of salt water and shape change of salt water case were considered. And the effect of lengths of suspending rods, attaching angles, vertical and horizontal position, stiffness of spring on the change of vibration were also considered. To identify the effect of salt water on vibration, some measurements were done. When salt water was positioned at upper part, the effect was most and this coincides with the tendency of simulation.

• 소음진동
• /
• 제8권2호
• /
• pp.324-330
• /
• 1998

The forced vibration analysis of the outer-clamped spinnig annular disk with arbitrary in-plane is formulated to investigate the influence of non-uniform tension on the cutting accuracy of wafer cutting machine. The arbitrary in-plan force along the outer edge of an annular plate is expressed as a Fourier series. Galerkin method and modal superposition method are employed to obtain the forced responses under the static force and the impulse force in astationary coordinate. Through qualitative and quantitative analyses, it can be found that forced and impulse responses are sensitive to the non-uniformity of in-plane force, which can bring a bad effect to the accuracy of wafer cutting process. Also, in case of a spinning disk with non-uniform in-plane force, critical speed is required to define in a different way, compared with conventional definition in axi-symmetrical spinning disk.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.622-630
• /
• 2010

The increase of the spindle speed to enhance the productivity in ring spinning processes has been limited by yarn tension and heat generation of the traveller/ring. The main causes of yarn tension are 1) the force added directly to the yarn by the rotation of the spindle and 2) the centrifugal force exerted by the yarn balloon generated by traveller rotation. The dominant causes of heat generation are 1) the friction between the ring and traveller and 2) the friction between the traveller and yarn. These factors cause yarn end-breaks and heat damage. In the case of the staple yarn manufacturing process for PET (polyester) and nylon (a heat plasticity material), the rotational speed of the ring spinning system has deteriorated to 10,000rpm. The objective of this study was to develop a rotating ring which has dynamic stability, high productivity and a simple structure to overcome the limitations of the conventional fixed ring/traveller system. The results of this study revealed that the spinning tension could be reduced by 67.8% using the newly developed rotating ring.

• 한국염색가공학회지
• /
• 제32권4호
• /
• pp.239-244
• /
• 2020

Polyethylene (PE) micro-fiber have been prepared at different hot air temperature (60, 80 and 100 ℃) and different pressure (20, 40, 60 and 80 kPa) by melt centrifugal spinning technique. The parameters of melting centrifugal spinning including polymer contents, rotational velocity, temperature of hot air and pressure were optimized for the fabrication process. The study showed that 8000 rpm rotational velocity, 80 ℃ heated hot air and 40 kPa air pressure are the best condition to obtain uniform and strong PE fiber. The prepared PE fibers were analyzed by field emission scanning electron microscope and universal testing machine and found that fibers with reduced diameter and improved tensile strength are obtained at hot air condition.

• 한국항공우주학회지
• /
• 제35권1호
• /
• pp.79-86
• /
• 2007

회전 발사체용 마그너스 효과 풍동실험 측정장치를 개발하였다. 국방과학연구소 풍동실험실에서는 고속풍동실험에 앞서 지상기능시험과 마그너스 저속풍동실험을 수행하였으며 마그너스 모형은 분당 약 6,000~10,000 회전하였으며, 속도 100 m/sec에서 측정한 마그너스 효과는 무차원 회전특성인자에 대해 선형적인 변화특성을 보였다. 동일형상 모형에 대해 미국 AEDC-4T 풍동에서 기 수행하였던 마그너스 측정결과와의 비교검토를 수행하였다.

• 열처리공학회지
• /
• 제13권4호
• /
• pp.265-271
• /
• 2000

The microstructural change and transformation characteristics with cooling rate i.e. wheel speed were investigated in 82.8wt%Cu-12.8wt%Al-4.3wt%Ni SMA ribbons fabricated by melt-spinning. The thickness and width of ribbon were decreased with increasing wheel speed, while the uniformity of it was improved. At same wheel speed, the grain size of the contact surface of ribbon was smaller than that of free surface. The mean grain size was decreased with increasing wheel speed, resulted in obtaining grains with $3{\mu}m$ in mean diameter in the wheel speed of 30 m/s. However, micro-voids and cracks at grain boundary could be observed at higher wheel speed. $M_s$ and $A_s$ temperatures were decreased, and $M_s{\sim}M_f$ and $A_s{\sim}A_f$ temperature ranges were broadened with increasing wheel speed. All the ribbons were retained the ordered $D0_3$ due to rapid cooling, the volume fraction of it was increased with increasing wheel speed.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2000년도 봄 한국섬유공학회 학술발표회 논문집(Proceedings of the Korean Textile Conference)
• /
• pp.125-128
• /
• 2000

Chemical cellulose from an ascidian tunic is isolated by extraction, digestion and bleaching steps. The content of $\alpha$-cellulose was above 98 wt%, and it's DPw was about 918. A new regenerated cellulose fiber from the chemical cellulose obtained in this study was made using NMMO/water(87/13 wt%) as a solvent by dry jet-wet spinning. The effects of spinning speed and cellulose content of spinning dope on the properties were investigated.

• Fibers and Polymers
• /
• 제6권1호
• /
• pp.19-27
• /
• 2005

High-speed melt spinning of syndiotactic polystyrene was carried out using high and low molecular weight poly­mers, HM s-PS and LM s-PS, at the throughput rates of 3 and 6 g/min. The effect of take-up velocity on the structure and properties of as-spun fibers was investigated. Wide angle X-ray diffraction (WAXD) patterns of the as-spun fibers revealed that the orientation-induced crystallization started to occur at the take-up velocities of 2-3 km/min. The crystal modification was a-form. Birefringence of as-spun fibers showed negative value, and the absolute value of birefringence increased with an increase in the take-up velocity. The cold crystallization temperature analyzed through the differential scanning calorimetry (OSC) decreased with an increase in the take-up velocity in the low speed region, whereas as the melting temperature increased after the on-set of orientation-induced crystallization. It was found that the fiber structure development proceeded from lower take-up velocities when the spinning conditions of higher molecular weight and lower throughput rate were adopted. The highest tensile modulus of 6.5 GPa was obtained for the fibers prepared at the spinning conditions of LM s-PS, 6 g/min and 5 km/min, whereas the highest tensile strength of 160 MPa was obtained for the HM s-PS fibers at the take-up velocity of 2 km/min. Elongation at break of as-spun fibers showed an abrupt increase, which was regarded as the brittle-duc­tile transition, in the low speed region, and subsequently decreased with an increase in the take-up velocity. There was a uni­versal relation between the thermal and mechanical properties of as-spun fibers and the birefringence of as-spun fibers when the fibers were still amorphous. The orientation-induced crystallization was found to start when the birefringence reached -0.02. After the starting of the orientation-induced crystallization, thermal and mechanical properties of as-spun fibers with similar level of birefringence varied significantly depending on the processing conditions.

• 한국조명전기설비학회지:조명전기설비
• /
• 제8권4호
• /
• pp.55-62
• /
• 1994

본 논문에서는 기존의 펌프나 가스를 이용한 강제유동식 시스템과는 달리 회전원통을 이용한 유동대전현상에 대하여 연구하여, 강제유동식에서의 대전특성과 비교, 분석하였다. 연구결과, 회전원통 시스템에서의 회전원통의 회전속도 및 온도에 따른 유동대전 특성은 강제유동식과 같은 경향을 보여 회전원통 시스템이 유동대전현상을 연구하는데 적합함을 알 수 있었다. 회전원통시스템은 강제유동식에 비하여 실험장치의 기계적 구조가 간단하고, 적은 양의 절연유만이 필요하며, 여러 가지 다른 물질로 실험하기가 비교적 편리하였다. 또한 대전 방지제의 첨가나 절연유의 열화에 따른 대전현상 등을 연속적으로 측정할 수 있는 특징이 있음을 알 수 있었다.