• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.347.1-347.1
• /
• 2016

Screen printing is commonly used to form the electrode for crystalline silicon solar cells. However, it has caused high resistance and low aspect ratio, resulting in decrease of conversion efficiency. Accordingly, Ni/Cu/Ag plating method could be applied for crystalline silicon solar cells to reduce contact resistance. For Ni/Cu/Ag plating, laser ablation process is required to remove anti-reflection layers prior to the plating process, but laser ablation results in surface damage and then decrease of open-circuit voltage and cell efficiency. Another issue with plating process is ghost plating. Ghost plating occurred in the non-metallized region, resulting from pin-hole in anti-reflection layer. In this paper, we investigated the effect of Ni/Cu/Ag plating on the electrical properties, compared to screen printing method. In addition, phosphoric acid layer was spin-coated prior to laser ablation to minimize emitter damage by the laser. Phosphorous elements in phosphoric acid generated selective emitter throughout emitter layer during laser process. Then, KOH treatment was applied to remove surface damage by laser. At this step, amorphous silicon formed by laser ablation was recrystallized during firing process and remaining of amorphous silicon was removed by KOH treatment. As a result, electrical properties as Jsc, FF and efficiency were improved, but Voc was lower than screen printed solar cells because Voc was decreased due to surface damage by laser process. Accordingly, we expect that efficiency of solar cells could be improved by optimization of the process to remove surface damage.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.149-155
• /
• 2015

Purpose : Recently, many researchers and golf coachers demonstrated that X-factor and X-factor stretch had a co-relationship with driving distance. However, its relationship is still controversial and ambiguous. Thus, the aim of this study was to examine the relationship among X-factor, X-factor stretch and swing-related factors, including driving distance in elite golfers. Method : Seventeen male elite golfers (handicap: ${\leq}4$) with no history of musculo-skeletal injuries participated in the study. Thirty spherical retro-reflective markers were placed on including the middle point of PSIS, the right/left ASIS, the right/left lateral acromion of the scapula, driver head and shaft grip. All motion capture data was collected at 100Hz using 6 infrared cameras. Carry distance, club speed, ball speed, smash factor, launch angle, and spin rate were collected from radar-based device, TrackMan. Results : Pearson's correlation coefficient method was used to find the correlations among X-factor, X-factor stretch and swing-related factors. Positive correlations between driving distance and other swing-related factors which include club speed(r=.798, p<.001), and ball speed(r=.948, p<.001) were observed. In contrast to the swing-related factors, X-factor and X-factor stretch had no relationship to driving distance. Conclusion : These results indicate that X-factor and X-factor stretch are not key regulators in driving distance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.137-137
• /
• 2003

Optical amplificator have been used to compensate the losses in the optical signal transmission and processing. Today, there has been increasing demand for the very low cost optical amplifier. Sol-gel offers considerable potential both low cost manufacture, and for great flexibility in materials composition and structure. In addition, the sol-gel process is a very attractive method for producing porous materials with controlled structure. In this work, we present the potoluminescence properties of Er doped A1$_2$O$_3$/SiO$_2$ films. Erbium doped alumina nano sol was prepared by Al(NO$_3$)$_3$.9$H_2O$ and Er(NO$_3$)$_3$.5$H_2O$ through hydrolysis and peptization, and then GPS (3-Glycidoxypropyltrimethoxysilane) was added into Er doped alumina nano sol for organic- inorganic hybridization. Er doped A1$_2$O$_3$/SiO$_2$ film was obtained by spin coating, dip coating and thermal treatment from 30$0^{\circ}C$~120$0^{\circ}C$, and there were crack-free after thermal treatment. The thickness of film was measured SEM, and the porosity of film was characterized by BET and TGA. The crystal phase of Er doped A1$_2$O$_3$/SiO$_2$ were determined by XRD. Finally, the photoluminescence properties of Er doped A1$_2$O$_3$/SiO$_2$ films will be discuss with the consideration of porosity and crystallity.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.762-769
• /
• 2015

The titania ($TiO_2$) nanoparticles with a diameter 2?3 nm were synthesized by controlling hydrolysis of titanium tetraisopropoxide (TTIP) in acid solution. Organic-inorganic hybrid coating solutions were prepared by reacting the titania nanoparticles with 3-glycidoxypropyl trimethoxysilane (GPTMS) by the sol-gel method. The hard coating films with high refractive index were obtained by curing thermally at $120^{\circ}C$ after spin-coating the coating solutions on the polycarbonate (PC) sheets. The coating films showed high optical transparency of 90% in the visible range and exhibited a pencil hardness of 2H. Also, the refractive index at 633 nm wavelength of coating films enhanced from 1.502 to 1.584 as the weight content of titania nanoparticles in the coating solutions increased from 4% to 25%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.533-538
• /
• 2001

The ZnSe sample grown by chemical bath deposition (CBD) method were annealed in Ar gas at 450$^{\circ}C$ Using extrapolation method of X-ray diffraction pattern, it was found to have zinc blend structure whose lattice parameter a$\_$o/ was 5.6687 ${\AA}$. From Hall effect, the mobility was likely to be decreased by impurity scattering at temperature range from 10 K to 150 K and by lattice scattering at temperature range from 150 K to 29 3K. The band gap given by the transmission edge changed from 2.7005 eV at 293 K to 2.8739 eV at 10 K. Comparing photocurrent peak position with transmission edge, we could find that photocurrent peaks due to excition electrons from valence band, $\Gamma$$\_$8/ and $\Gamma$$\_$7/ to conduction band $\Gamma$$\_$6/ were observed at photocurrent spectrum. From the photocurrent spectra by illumination of polarized light on the ZnSe thin film, we have found that values of spin orbit coupling splitting Δso is 0.0981 eV. From the PL spectra at 10 K, the peaks corresponding to free bound excitons and D-A pair and a broad emission band due to SA is identified. The binding energy of the free excitons are determined to be 0.0612 eV and the dissipation energy of the donor -bound exciton and acceptor-bound exciton to be 0.0172 eV, 0.0310 eV, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.307-314
• /
• 1998

PZT thin films were fabricated by the Sol-gel method. Starting materials used for the preparation of the stock solution were Pb-acetate trihydrate, Zr-normal propoxide and Ti-isopropoxide. 2-Methoxyethanol and iso-propanol were used for solution. For studying the diffusion of Pb ion into the substrates. We used bare Si substrate, $SiO_2/Si$ substrates which was produced by thermal oxidation and $TiO_2/SiO_2/Si$ which was mad by Sol-gel method. Densification and adhesion of thin films were observed by SEM. Phase formation of thin films and diffusion of Pb ion into the substrate were examined by XRD and ESCA, respectively. In the case of bare Si and $SiO_2/Si$ substrate, we obtained the perovskite phase at $700^{\circ}C$ and restricted a little the diffusion of Si ion into the film with $SiO_2$ buffer layer. In the case of $TiO_2/SiO_2/Si$, perovskite phase were obtained at $500^{\circ}C$ and the diffusion of Pb ion and Si ion were restriced.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.2
• /
• pp.23-28
• /
• 2013

Microlens array as basic element of the optical system have been fabricated with various focal length (mainly with long focal length) depending on the purpose of application. In this paper, the microlens arrays were fabricated for observing fluorescent images within sol-gel. Though the fluorescent signal is very low, the microlens array can help obtaining clear images through extracting the fluorescent light from sol-gel. We fabricated microlens arrays with short focal length, which can extract the light using photoresist thermal reflow method. In the experiment, the diameter of microlens decreased after thermal reflow because the solvent within the photoresist was vaporized. Therefore, to compensate the shape error by this reduction, microlens diameter in photomask was altered and spin-coat recipe of photoresist were modified.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.274-278
• /
• 2008

Hard coating solutions were prepared from glycidoxypropyl trimethoxysilane (GPTMS) and methacryloxypropyl trimethoxysilane (MPTMS) precursors with different molar ratios of 10:0, 9:1, 7:3, 5:5, 3:7, and 0:10, respectively, by the sol-gel method. The polycarbonate (PC) sheets were spin-coated, and cured at $130^{\circ}C$ for 3 h. The effect of the GPTMS:MPTMS molar ratios of the mixture was investigated on the properties of coating films. The highest pencil hardness and adhesion to PC sheets of coating films were found for solution with GPTMS:MPTMS molar ratio of 5:5. Also, the pencil hardness of coating films was increased with increasing the $H_2O$ content in the coating solutions.

• Textile Coloration and Finishing
• /
• v.30 no.3
• /
• pp.199-207
• /
• 2018

In this study, the properties of polypropylene(PP) non-woven fabric spun under various conditions by the Melt-blown method were verified, and the deodorant content and deodorization of PP non-woven fabric after deodorant-treatment were investigated. PP non-woven fabrics are manufactured by varying the temperature of spin beam, hot air temperature and amount, the RPM of collector R/O and the distance between collector and spinneret, which affects the structure of the non-woven fabric. After that, the structural characteristics and air permeability of the non-woven fabric were measured. The experimental results show that the amount of air, the distance between the collector and the spinneret significantly affect the structural characteristics and air permeability of the PP non-woven fabric. And, regardless of the weight of the PP non-woven fabric, the deodorizing effect of UiO-66 MOF deodorant add-on ratio and content was higher.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.181-186
• /
• 2017

Single point incremental forming (SPIF) is a sheet-forming technique. It is a die-less sheet metal manufacturing process for rapid prototyping and small batch production. The Critical parameters in the forming process include tool diameter, step depth, feed rate, spindle speed, etc. In this study, these parameters and the die shape corresponding to the Varying Wall Angle Conical Frustum(VWACF) model were used for forming 0.8mm in thick Al5052-O sheets. The Taguchi method of Experiments of Design (DOE) and Grey relational optimization were used to determine the optimum parameters in SPIF. A response study was performed on formability, spring back, and thickness reduction. The research shows that the optimum combination of these parameters that yield best performance of SPIF is as follows: tool diameter, 6mm; spin speed, 60rpm; step depth, 0.3mm; and feed rate, 500mm/min.