• Nuclear Engineering and Technology
• /
• 제43권2호
• /
• pp.149-158
• /
• 2011

Metal waste generated from the pyroprocessing of 10 MtU of spent fuel was classified by comparing the specific activity of a relevant radionuclide with the limit value of the specific activity specified in the Korean acceptance criteria for a lowand intermediate-level waste repository. A Korean Optimized Fuel Assembly design with a 17${\times}$17 array, an initial enrichment of 4.5 weight-percent, discharge burn-up of 55 GWD/MtU, and a 10-year cooling time was considered. Initially, the mass and volume of each structural component of the assembly were calculated in detail, and a source term analysis was subsequently performed using ORIGEN-S for these components. An activation cross-section library generated by the KENO-VI/ORIGEN-S module was utilized for top-end and bottom-end pieces. As a result, an Inconel grid plate, a SUS plenum spring, a SUS guide tube subpart, SUS top-end and bottom-end pieces, and an Inconel top-end leaf spring were determined to be unacceptable for the Gyeongju low- and intermediate-level waste repository, as these waste products exceeded the acceptance criteria. In contrast, a Zircaloy grid plate and guide tube can be placed in the Gyeongju repository. Non-contaminated Zircaloy cladding occupying 76% of the metal waste was found to have a lower level of specific activity than the limit value. However, Zircaloy cladding contaminated by fission products and actinides during the decladding process of pyroprocessing was revealed to have 52 and 2 times higher specific activity levels than the limit values for alpha and $^{90}Sr$, respectively. Finally, it was found that 88.7% of the metal waste from the 17${\times}$17 Korean Optimized Fuel Assembly design should be disposed of in a deep geological repository. Therefore, it can be summarized that separation technology with a higher decontamination factor for transuranics and strontium should be developed for the efficient management of metal waste resulting from pyroprocessing.

• 방사성폐기물학회지
• /
• 제20권2호
• /
• pp.231-241
• /
• 2022

Several countries, including Korea, are considering the direct disposal of spent nuclear fuels. The radiological safety assessment results published after a geological repository closure indicate that the instant release is the main radiation source rather than the congruent release. Three Safety Case reports recently published were reviewed and the IRF values of seven long-lived radionuclides, including relevant experimental results, were compared. According to the literature review, the IRF values of both the CANDU and low burnup PWR spent fuel have been experimentally measured and used reasonably. In particular, the IRF values of volatile long-lived nuclides, such as ¹²⁹I and ¹³⁵Cs, were estimated from the FGR value. Because experimental leaching data regarding high burnup spent nuclear fuels are extremely scarce, a mathematical modelling approach proposed by Johnson and McGinnes was successfully applied to the domestic high burnup PWR spent nuclear fuel to derive the IRF values of iodine and cesium. The best estimate of the IRF was 5.5% at a discharge burnup of 55 GWd tHM^-1.

• Nuclear Engineering and Technology
• /
• 제40권1호
• /
• pp.9-20
• /
• 2008

Since plutonium accounts for 40-50% of the power produced by uranium fuels, spent fuel contains only residual plutonium. Management of this plutonium is one of the aspects influencing the choice of a fuel cycle back-end option: reprocessing, direct disposal or wait-and-see. Different grades and qualities of plutonium exist depending from their specific generation conditions; all are valuable fissile material. Safeguard authorities watch the inventories of civil plutonium, but access to those data is restricted. Independent evaluations have led to an estimated current inventory of 220t plutonium in total (spent fuel, separated civil plutonium and military plutonium). If used as MOX fuel, it would be sufficient to feed all the PWRs and BWRs worldwide during 7 years or to deploy a FBR park corresponding to 150% of today' s installed nuclear capacity worldwide, which could then be exploited for centuries with the current stockpile of depleted and spent uranium. The energy potential of plutonium deteriorates with storage time of spent fuel and of separated plutonium, due to the decay of $^{241}Pu$, the best fissile isotope, into americium, a neutron absorber. The loss of fissile value of plutonium is more pronounced for usage in LWRs than in FBR. However, keeping the current plutonium inventory for an expected future deployment of FBRs is counterproductive. Recycling plutonium reduce the required volume for final disposal in an underground repository and the cost of final disposal. However, the benefits of utilizing an energy resource and of reducing final disposal liabilities are not the only aspects that determine the choice of a back-end policy.

• 방사성폐기물학회지
• /
• 제6권2호
• /
• pp.147-154
• /
• 2008

국내 원자력발전소의 사용후핵연료 저장용량의 포화가 10년 이내에 예상되고 있으며, 소외중간저장방식을 관리 방안으로서 선정할 경우, 상당한 양의 사용후핵연료 운반이 해상 혹은 육로를 통해 매년 이루어져야만 한다. 본 논문에서는 4곳의 원자력발전소부지에 분산 저장되어 있는 사용후핵연료를 해안에 위치한 가상의 중간저장시설과 영구처분시설을 대상으로 사용후핵연료 운반물량을 효과적으로 분석할 수 있는 체계를 구축하였다. 각 발전소 부지, 중간저장시설, 영구처분시설의 저장고를 중심으로 사용후핵연료 물질 수지식을 세우고, 이에 대한 해를 VISUAL BASIC으로 구하여 운반 물량 분석이 용이하게 수행할 수 있는 컴퓨터 프로그램(CASK)을 개발하였다. 개발된 물량 분석 프로그램을 활용하여 4개 원자력 발전소 부지로부터 사용후핵연료 운반 물량을 분석하고, 운반물량 파라미터 분석을 통하여 본 프로그램의 활용도를 보였다. 개발된 사용후핵연료 운반 물량 분석 체계는 향후 운반비용 분석에도 유용하게 활용될 것이다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.259-266
• /
• 2001

This paper presents the results of a structural analysis to determine design variables such as the inner basket array type, and thicknesses of the outer shell and the lid and bottom of a spent nuclear fuel disposal canister. The canister construction type introduced here is a solid structure with a cast iron insert and a corrosion resistant overpack, which is designed for the spent nuclear fuel disposal in a deep repository in the crystalline bedrock, entailing an evenly distributed load of hydrostatic pressure from the groundwater and large swelling pressure from the bentonite buffer. Hence, the canister must be designed to withstand these large pressure loads. Many design variables may affect the structural strength of the canister. In this study, among those variables, the array type of inner baskets and thicknesses of outer shell and lid and bottom are attempted to be determined through a linear static structural analysis. Canister types studied here are one for the pressurized water reactor (PWR) fuel and another for the Canadian deuterium and uranium reactor (CANDU) fuel.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2009년도 학술논문요약집
• /
• pp.187-187
• /
• 2009

Opening of fractures induced by shear dilation or normal deformation can be a significant source of fracture permeability change in fractured rock, which is important for the performance assessment of geological repositories for spent nuclear fuel. As the repository generates heat and later cools the fluid-carrying ability of the rocks becomes a dynamic variable during the lifespan of the repository. Heating causes expansion of the rock close to the repository and, at the same time, contraction close to the surface. During the cooling phase of the repository, the opposite takes place. Heating and cooling together with the, virgin stress can induce shear dilation of fractures and deformation zones and change the flow field around the repository. The objectives of this work are to examine the contribution of thermal stress to the shear slip of fracture in mid- and far-field around a KBS-3 type of repository and to investigate the effect of evolution of stress on the rock mass permeability. In the first part of this study, zones of fracture shear slip were examined by conducting a three-dimensional, thermo-mechanical analysis of a spent fuel repository model in the size of 2 km $\times$ 2 km $\times$ 800 m. Stress evolutions of importance for fracture shear slip are: (1) comparatively high horizontal compressive thermal stress at the repository level, (2) generation of vertical tensile thermal stress right above the repository, (3) horizontal tensile stress near the surface, which can induce tensile failure, and generation of shear stresses at the comers of the repository. In the second part of the study, fracture data from Forsmark, Sweden is used to establish fracture network models (DFN). Stress paths obtained from the thermo-mechanical analysis were used as boundary conditions in DFN-DEM (Discrete Element Method) analysis of six DFN models at the repository level. Increases of permeability up to a factor of four were observed during thermal loading history and shear dilation of fractures was not recovered after cooling of the repository. An understanding of the stress path and potential areas of slip induced shear dilation and related permeability changes during the lifetime of a repository for spent nuclear fuel is of utmost importance for analysing long-term safety. The result of this study will assist in identifying critical areas around a repository where fracture shear slip is likely to develop. The presentation also includes a brief introduction to the ongoing site investigation on two candidate sites for geological repository in Sweden.

• 방사성폐기물학회지
• /
• 제18권spc호
• /
• pp.63-74
• /
• 2020

The operational safety assessment is an important part of a safety case for the deep geological repository of spent fuels. It consists of different stages such as the identification of initiating events, event tree analysis, fault tree analysis, and evaluation of exposure doses to the public and radiation workers. This study develops a probabilistic safety assessment method for the operational safety assessment and establishes an assessment framework. For the event and fault tree analyses, we propose the advanced information management system for probabilistic safety assessment (AIMS-PSA Manager). In addition, we propose the Radiological Safety Analysis Computer (RSAC) program to evaluate exposure doses to the public and radiation workers. Furthermore, we check the applicability of the assessment framework with respect to drop accidents of a spent fuel assembly arising out of crane failure, at the surface facility of the KRS⁺ (KAERI Reference disposal System for SNFs). The methods and tools established through this study can be used for the development of a safety case for the KRS⁺ system as well as for the design modification and the operational safety assessment of the KRS⁺ system.

• 한국전산구조공학회논문집
• /
• 제20권4호
• /
• pp.427-433
• /
• 2007

가압경수로(PWR)에서 배출되는 고준위폐기물을 지하 500m의 화강암 암반의 처분장에 장기간(약 10,000년 동안) 처분하기 위하여 여러 구조적 안전성 평가 수행을 통하여 처분용기모델이 개발되었다. 기존에 설계된 가압경수로용 처분용기 모델은 구조적 안전성은 문제가 없으나 너무 무거운 단점이 지적되었다. 따라서 구조적 안전성을 유지하면서 좀 더 경량화 된 처분용기모델을 개발하는 것이 요구된다. 기존의 처분용기모델이 무거워진 한가지 이유는 처분용기 개발 시 적용된 외력조건 및 안전계수 등에 대한 조건들을 너무 엄격하게 적용했기 때문이라고 사료되기 때문에 이런 조건들을 완화하여 처분용기의 재원들을 조정하여 구조해석을 다시 수행하는 것이 요구된다. 따라서 본 논문에서는 설계 완성된 기존의 처분용기에 대하여 외력 조건 및 용기의 재원(두께 등) 들을 변화시키면서 구조해석을 재 수행하여 구조적 안전성 평가를 보완하였다. 이를 바탕으로 외력 조건에 따른 처분용기의 재원 등을 재 산출한다. 보완 해석 결과 기존의 122cm의 처분용기의 직경을 102cm까지 줄여 경량화 시킬 수 있음이 확인되었다.

• Nuclear Engineering and Technology
• /
• 제54권8호
• /
• pp.2819-2827
• /
• 2022

The disposal area of a deep geological repository (DGR) for the disposal of spent nuclear fuels (SNFs) is estimated considering the spacing between deposition holes and between disposal tunnels, as determined by a thermal analysis using the decay heat of a reference SNF. Given the relatively large amount of decay heat of the reference SNF, the disposal area of the DGR is found to be overestimated. Therefore, we develop a computer program using MATLAB, termed ACom (Assembly Combination), to combine SNFs when stored in canisters such that the decay heat per canister is evenly distributed. The stability of ACom was checked and the overall distribution of the decay heat per canister was analyzed. Finally, ACom was applied to disposal scenarios suggested in the conceptual design of a DGR for SNFs, and it was confirmed that the decay heat per canister could be evenly distributed and that the maximum decay heat of the canister could be much lower than that of a canister estimated using a reference SNF. ACom can be used to improve the disposal efficiency by reducing the disposal area of a DGR for SNFs by ensuringg a relatively even distribution of decay heat per canister.

• 방사성폐기물학회지
• /
• 제17권3호
• /
• pp.355-362
• /
• 2019

본 논문에서는 최근 새롭게 제안된 심부수평시추공처분 개념을 소개하고, 우리나라 여건에서는 어떻게 적용될 수 있을지에 대하여 고려해 보았다. 이 개념은 방향제어시추기술로 심부수평시추공을 설치하고 고준위방사성폐기물을 처분하는 개념으로, 경제성과 안전성에서 기존의 동굴식 처분개념에 비해 큰 장점을 가지고 있는 것으로 평가된다. 그러나, 아직까지 아이디어 수준이므로 국제사회에서 처분 안전성과 성능을 실증하기까지 시간이 꽤 걸릴 것이고, 규제기관의 지침 개발도 뒷받침되어야 하는 문제가 있다. 우리나라는 국토가 좁고 인구밀도가 높아 NIMBY (Not In My Back Yard) 현상이 강할 수 밖에 없고, 더불어 사용후핵연료 발생량도 적지 않아 매우 어려운 입지여건을 가지고 있다. 이러한 여건에서 연안 육지부보다는 대륙붕의 안정된 환경의 장점을 살려 연안 해저암반을 심부수평시추공처분 개념의 처분영역으로 활용한다면 해당 지역사회의 심리적인 불안감을 획기적으로 완화시킬 수 있고 처분 안전성도 향상시킬 수 있을 것으로 기대한다. 더불어, 중앙집중식 심부동굴처분시설을 건설하는 경우에도 대륙붕을 활용하여 동일한 장점을 살리는 것을 고려해볼 필요가 있다.