• 한국표면공학회지
• /
• 제56권1호
• /
• pp.84-93
• /
• 2023

The spent nuclear fuel is burned during the planned cycle in the plant and then generates elements such as actinide series, fission products, and plutonium with a long half-life. An 'interim storage' step is needed to manage the high radioactivity and heat emitted by nuclides until permanent-disposal. In the case of Korea, there is no space to dispose of high-level radioactive waste after use, so there is a need for a period of time using interim storage. Therefore, the intensity of neutrons and gamma-ray must be determined to ensure the integrity of spent nuclear fuel during interim storage. In particular, the most important thing in spent nuclear fuel is burnup evaluation, estimation of the source term of neutrons and gamma-ray is regarded as a reference measurement of the burnup evaluation. In this study, an analysis of spent nuclear fuel was conducted by setting up a virtual fuel burnup case based on CE16×16 fuel to check the total amount and spectrum of neutron, gamma radiation produced. The correlation between BU (burnup), IE (enrichment), and CT (cooling time) will be identified through spent nuclear fuel burnup calculation. In addition, the composition of nuclide inventory, actinide and fission products can be identified.

• 방사선산업학회지
• /
• 제18권3호
• /
• pp.255-266
• /
• 2024

The uranium nuclear fuel used in nuclear power generation needs to be replaced with new fuel after a certain period. In South Korea, the spent nuclear fuel generated during this process is temporarily stored within the nuclear power plant site, and there are ongoing issues with the saturation of storage capacity. To address these problems, the South Korea government has established a plan to manage high-level radioactive waste, including provisions for securing interim storage facilities. An interim storage facility is designed to safely store spent nuclear fuel for certain period before its permanent disposal. This study analyzed leading international cases of interim storage facilities that are technically feasible and can reduce the operating period of temporary storage facilities for spent nuclear fuel within nuclear power plant sites. It also presented the technical concepts required for the operation of interim storage facilities for spent fuel from PWR(Pressurized Water Reactor), reflecting the situation in South Korea.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.470-473
• /
• 2005

Spent nuclear fuels are regarded as a high level radioactive waste and they will be disposed in a deep geological repository. To maintain the safety of the repository for hundreds of thousands of years, the spent fuels are encapsulated in a disposal canister and the canister containing spent fuels should have the structural integrity and the corrosion resistance below the several hundreds meters from the ground surface. In this study, the concept of the spent fuel encapsulation process and the process equipment fur deep geological disposal were established. To do this, the design requirements, such as the functions and the spent fuel accumulations, were reviewed. Also, the design principles and the bases were established. Based on the requirements and the bases, the encapsulation process and the equipment from spent fuel receiving process to transferring canister into the underground repository including hot cell processes was established. The established concept of the spent fuel encapsulation process and the process equipment will be improved continuously with the future studies. And this concept can be effectively used in implementing the reference repository system of our own case.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.77-84
• /
• 2000

In this paper, the stress analysis of the cast iron insert of spent nuclear fuel disposal canister in a deep repository at 500m underground is done for the underground pressure variation. Since the nuclear fuel disposal usually emits much heat and radiation, its careful treatment is required. And so a long term safe repository at a deep bedrock is used. Under this situation, the canister experiences some mechanical external loads such as hydrostatic pressue of underground water, swelling pressure of bentonite, sudden rock movement etc.. Hence, the canister should be designed to withstand these loads. The cast iron insert of the canister mainly supports these loads. Therefore, the stress analysis of the cast iron insert is done to determine the design variables such as the diameter versus length of canister and the number and array type of inner baskets in this paper, The linear static structural analysis is done using the finite element analysis method. And the finite element analysis code, NISA, is used for the computation.

• Nuclear Engineering and Technology
• /
• 제54권8호
• /
• pp.2819-2827
• /
• 2022

The disposal area of a deep geological repository (DGR) for the disposal of spent nuclear fuels (SNFs) is estimated considering the spacing between deposition holes and between disposal tunnels, as determined by a thermal analysis using the decay heat of a reference SNF. Given the relatively large amount of decay heat of the reference SNF, the disposal area of the DGR is found to be overestimated. Therefore, we develop a computer program using MATLAB, termed ACom (Assembly Combination), to combine SNFs when stored in canisters such that the decay heat per canister is evenly distributed. The stability of ACom was checked and the overall distribution of the decay heat per canister was analyzed. Finally, ACom was applied to disposal scenarios suggested in the conceptual design of a DGR for SNFs, and it was confirmed that the decay heat per canister could be evenly distributed and that the maximum decay heat of the canister could be much lower than that of a canister estimated using a reference SNF. ACom can be used to improve the disposal efficiency by reducing the disposal area of a DGR for SNFs by ensuringg a relatively even distribution of decay heat per canister.

• 방사성폐기물학회지
• /
• 제6권2호
• /
• pp.119-128
• /
• 2008

본 연구에서는 사용후핵연료 회수성과 처분밀도를 향상시킨 새로운 CANDU 사용후핵 연료처분시스템의 열해석을 수행하였다. 제안된 CANDU 사용후핵연료 처분방식 에서는 사용후핵연료의 회수성을 향상시키기 위해 일정 기간 동안 터널에 자연대류를 이용하여 저장하며, 처분밀도 향상을 위해 개선된 CAHDU 사용후핵연료 처분용기를 이용하고 있다. 제안된 CANDU 사용후핵연료 처분방식의 열적 안전성을 검토하고자 ANSYS 10.0 CFX 코드를 사용하여 시스템 전체의 정상상태 열 해석을 2단계로 나누어 수행하였다. 1단계에서는 터널간격이 처분터널 내부 온도에 미치는 영향을 분석하기 위해 터널 간격에 따른 처분터널 내벽온도 변화를 계산하였다. 계산 결과 99%의 붕괴열이 대류에 의해 냉각되는 것을 확인하였고, 이로 인해 터널 간격은 처분터널 내부 온도에 거의 영향을 주지 않았다. 2단계 계산에서는 터널간격 60 m에서 환기 설비를 고려한 처분터널의 내벽온도를 계산하였고, 이 결과는 처분터널 내부 처분용기의 표면온도를 구하기 위해 사용되었다. 계산결과, 처분용기의 표면온도는 최대 $119^{\circ}C$, 평균 $79.9^{\circ}C$로 계산되었다. 처분용기 최대온도에 따른 처분용기 내부 바스켓 피복재 최대온도는 $140.9^{\circ}C$로 계산하였으며, 이는 피복재 열적 특성을 고려하였을 때 충분한 열적 안전성을 가지고 있다고 판단되었다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.329-329
• /
• 1999

• 방사성폐기물학회지
• /
• 제21권4호
• /
• pp.451-463
• /
• 2023

With South Korea increasingly focusing on nuclear energy, the management of spent nuclear fuel has attracted considerable attention in South Korea. This study established a novel procedure for selecting safety-relevant radionuclides for long-term safety assessments of a deep geological repository in South Korea. Statistical evaluations were performed to identify the design basis reference spent nuclear fuels and evaluate the source term for up to one million years. Safety-relevant radionuclides were determined based on the half-life criteria, the projected activities for the design basis reference spent nuclear fuel, and the annual limit of ingestion set by the Nuclear Safety and Security Commission Notification No. 2019-10 without considering their chemical and hydrogeological properties. The proposed process was used to select 56 radionuclides, comprising 27 fission and activation products and 29 actinide nuclides. This study explains first the determination of the design basis reference spent nuclear fuels, followed by a comprehensive discussion on the selection criteria and methodology for safety-relevant radionuclides.

• Nuclear Engineering and Technology
• /
• 제40권6호
• /
• pp.517-526
• /
• 2008

The widespread concern regarding the management of spent fuel that mainly contributes to nuclear waste has led to the development of the sodium-cooled fast reactor (SFR) as one of the most promising future types of reactors at both national and international levels. Various reactor deployment scenarios with SFR introductions with different conversion ratios in the existing PWR-dominant nuclear fleet have been assessed to optimize the SFR deployment strategy to replace PWRs with the view toward a reduction in the level of spent fuel as well as efficient uranium utilization through its reuse in a closed fuel cycle. An efficient reactor deployment strategy with the SFR introduction starting in 2040 has been drawn based on an SFR deployment strategy in which burners are deployed prior to breakeven reactors to reduce the amount of PWR spent fuel substantially at the early deployment stage. The PWR spent fuel disposal is reduced in this way by 98% and the cumulative uranium demand for PWRs to 2100 is projected to be 445 ktU, implying a uranium savings of 115 ktU. The SFR mix ratio in the nuclear fleet near the year 2100 is estimated to be approximately 35-40%. PWRs will remain as a main power reactor type until 2100 and SFRs will support waste minimization and fuel utilization.

• 방사성폐기물학회지
• /
• 제16권1호
• /
• pp.65-82
• /
• 2018

With the significant increase in spent ion-exchange resin generation, to meet the requirements of Waste Acceptance Criteria (WAC) of the Wolsong disposal facility in Korea, blending is considered as a method for enhancing disposal options for intermediate level waste from nuclear reactors. A mass balance formula approach was used to enable blending process with an appropriate mixing ratio. As a result, it is estimated around 44.3% of high activity spent resins can be blended with the overall volume of low activity spent resins at a 1:7.18 conservative blending ratio. In contrast, the reduction of high activity spent resins is considered a positive solution in reducing the amount of spent resins stored. In an economic study, the blending process has been proven to lower the disposal cost by 10% compared to current APR1400 treatment. Prior to commencing use of this blending method in Korea, coordinated discussion, and safety and health assessment should be undertaken to investigate the feasibility of fitting this blending method to national policy as a means of waste predisposal processing and management in the future.