• 융복합기술연구소 논문집
• /
• 제4권2호
• /
• pp.47-50
• /
• 2014

Voloxidation is a process for converting $UO_2$ into $U_3O_8$ while removing some volatile products in spent fuels (SF). Various oxidative gas conditions including air and mixture of Ar and $O_2$ could be adopted for the process. The gas flows into a reactor under high temperature ($>500^{\circ}C$) and components of SF are reacted with the gas. SF is composed of various components such as actinides, lanthanides, and alkali metals. Therefore, it is of significance to understand their behavior during the reactions for process development. However, due to the limit of available experiments, phase diagram analysis should be preceded. TPP diagram is constructed with respect to temperature-pressure-pressure. It shows a stable phase depending on partial pressures of gas components as well as temperature. In this work, we investigated TPP diagrams for actinides, lanthanides and other oxides to determine stable oxide forms under different gas conditions. The results would be used to set up a material balance under a pyroprocessing scheme of SF and compare the gas conditions for the optimization of fission products removal.

• Nuclear Engineering and Technology
• /
• 제49권7호
• /
• pp.1563-1570
• /
• 2017

In order to perform dry interim storage and transportation of the spent-fuel assemblies of the Bushehr Nuclear Power Plant, dual-purpose casks can be utilized. The effectiveness of different neutron-shield materials for the dual-purpose cask was analyzed through a set of calculations carried out using the Monte Carlo N-Particle (MCNP) code. The dose rate for the dual-purpose cask utilizing the recently developed materials of $epoxy/clay/B_4C$ and $epoxy/clay/B_4C/carbon$ fiber was less than the allowable radiation level of 2 mSv/h at any point and 0.1 mSv/h at 2 m from the external surface of the cask. By utilization of $epoxy/clay/B_4C$ instead of an ethylene glycol/water mixture, the dose rates on the side surface of the cask due to neutron sources and consequent secondary gamma rays will be reduced by 17.5% and 10%, respectively. The overall dose rate in this case will be reduced by 11%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.98-102
• /
• 2002

As the nuclear power plant has been operated continuously and increased gradually, transportation and storage of spent fuel are seriously considered nowadays. The transportation cask which contains radioactive material needs to be inspected about structural safety. About safety verification, description of IAEA Safety Standards states that cask must withstand hypothetical accident conditions. In this paper, 9m free drop impact analysis was performed for transportation cask and impact limiter by using the finite element methods. Furthermore, we obtained the dynamic behavior of wood to as compared with safety test results, and verified the safety of transportation cask.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2017년도 춘계학술논문요약집
• /
• pp.153-154
• /
• 2017

The thermal analysis of transportation and storage cask for SNF was conducted during short term loading operations for forced gas drying condition. The fuel cladding temperature in 6 regions of SNF in the cask during the short term loading operations for forced gas drying condition is shown in the Fig. 3. The thermal analysis results of calculated maximum cladding temperature in each process demonstrate that operating scenario of TFD in detailed design maintain well below the temperature limits of $400^{\circ}C$.

• Nuclear Engineering and Technology
• /
• 제46권4호
• /
• pp.547-556
• /
• 2014

Korea expects a shortage in storage capacity for spent fuels at reactor sites. Therefore, a need for more metal and/or concrete casks for storage systems is anticipated for either the reactor site or away from the reactor for interim storage. For the purpose of interim storage and transportation, a dual purpose metal cask that can load 21 spent fuel assemblies is being developed by Korea Radioactive Waste Management Corporation (KRMC) in Korea. At first the gamma and neutron flux for the design basis fuel were determined assuming in-core environment (the temperature, pressure, etc. of the moderator, boron, cladding, $UO_2$ pellets) in which the design basis fuel is loaded, as input data. The evaluation simulated burnup up to 45,000 MWD/MTU and decay during ten years of cooling using the SAS2H/OGIGEN-S module of the SCALE5.1 system. The results from the source term evaluation were used as input data for the final shielding evaluation utilizing the MCNP Code, which yielded the effective dose rate. The design of the cask is based on the safety requirements for normal storage conditions under 10 CFR Part 72. A radiation shielding analysis of the metal storage cask optimized for loading 21 design basis fuels was performed for two cases; one for a single cask and the other for a $2{\times}10$ cask array. For the single cask, dose rates at the external surface of the metal cask, 1m and 2m away from the cask surface, were evaluated. For the $2{\times}10$ cask array, dose rates at the center point of the array and at the center of the casks' height were evaluated. The results of the shielding analysis for the single cask show that dose rates were considerably higher at the lower side (from the bottom of the cask to the bottom of the neutron shielding) of the cask, at over 2mSv/hr at the external surface of the cask. However, this is not considered to be a significant issue since additional shielding will be installed at the storage facility. The shielding analysis results for the $2{\times}10$ cask array showed exponential decrease with distance off the sources. The controlled area boundary was calculated to be approximately 280m from the array, with a dose rate of 25mrem/yr. Actual dose rates within the controlled area boundary will be lower than 25mrem/yr, due to the decay of radioactivity of spent fuel in storage.

• Nuclear Engineering and Technology
• /
• 제49권2호
• /
• pp.442-449
• /
• 2017

Risk management of the Fukushima Daiichi Nuclear Power Station decommissioning is a great challenge. In the present study, a risk management framework has been developed for the decommissioning work. It is applied to fuel assembly retrieval from Unit 3 spent fuel pool. Whole retrieval work is divided into three phases: preparation, retrieval, and transportation and storage. First of all, the end point has been established and the success path has been developed. Then, possible threats, which are internal/external and technical/societal/management, are identified and selected. "What can go wrong?" is a question about the failure scenario. The likelihoods and consequences for each scenario are roughly estimated. The whole decommissioning project will continue for several decades, i.e., long-term perspective is important. What should be emphasized is that we do not always have enough knowledge and experience of this kind. It is expected that the decommissioning can make steady and good progress in support of the proposed risk management framework. Thus, risk assessment and management are required, and the process needs to be updated in accordance with the most recent information and knowledge on the decommissioning works.

• 방사성폐기물학회지
• /
• 제20권4호
• /
• pp.501-510
• /
• 2022

The nuclear criticality analyses considering burnup credit were performed for a spent nuclear fuel (SNF) disposal cell consisting of bentonite buffer and two different types of SNF disposal canister: the KBS-3 canister and small standardized transportation, aging and disposal (STAD) canister. Firstly, the KBS-3 & STAD canister containing four SNFs of the initial enrichment of 4.0wt% ²³⁵U and discharge burnup of 45,000 MWD/MTU were modelled. The k_eff values for the cooling times of 40, 50, and 60 years of SNFs were calculated to be 0.79108, 0.78803, and 0.78484 & 0.76149, 0.75683, and 0.75444, respectively. Secondly, the KBS-3 & STAD canister with four SNFs of 4.5wt% and 55,000 MWD/MTU were modelled. The k_eff values for the cooling times of 40, 50, and 60 years were 0.78067, 0.77581, and 0.77335 & 0.75024, 0.74647, and 0.74420, respectively. Therefore, all cases met the performance criterion with respect to the k_eff value, 0.95. The STAD canister had the lower k_eff values than KBS-3. The neutron absorber plates in the STAD canister significantly affected the reduction in k_eff values although the distance among the SNFs in the STAD canister was considerably shorter than that in the KBS-3 canister.

• Nuclear Engineering and Technology
• /
• 제14권4호
• /
• pp.196-203
• /
• 1982

본 논문에서는 고리 1호기의 기사용 핵연료 집합체를 수송하기 위한 Cask를 설계하였다. 이를 위하여 고리 1호기의 기사용 핵연료 집합체로부터 방출되는 감마선과 중성자를 계산하여 MORSE 및 ANISN전산 코드로써 차폐 계산을 수행하였다. 그 결과, 9개의 집합체를 동시에 수송할 수 있는 Steel Cask가 가장 적합하다는 것을 밝혔다. 이 Steel Cask에 대한 안전성을 평가하기 위하여 연료봉의 중심 온도와 복재온도를 계산하여 핵연료의 용융점보다 훨씬 낮음을 증명하였다. 또한 KENO와 MORSE전산 코드를 사용하여 임계도 계산을 수행하여 미임계 상태임을 증명하였다. 이로써 9개의 기사용 핵연료 집합체를 동시에 수송할 수 있는 Steel Cask를 간단히 설계하였다.

• 방사성폐기물학회지
• /
• 제13권4호
• /
• pp.243-251
• /
• 2015

국내 원자력발전은 현재 두 번째로 큰 전력 공급 방법이며 원전의 수 역시 증가되는 것으로 계획되어 있다. 그러나, 원자력발전에 의해 발생되는 사용후핵연료에 대해서는 아직 명확한 관리 정책이 확립되어 있지 않다. 원자로 이 후 핵물질 흐름과 관련된 후행 핵연료주기는 사용후핵연료 관리를 위한 기술들의 집합이다. 따라서, 사용후핵연료 관리 정책은 핵연료주기 선택과 함께한다. 핵연료주기 선택의 중요 항목은 경제성으로 이는 사적비용과 함께 외부비용을 더해 결정되어야 한다. 직접비용 인 사적비용과 달리 간접비용인 외부비용에 대한 연구는 원전에 집중되어 있으며 핵연료주기에 대한 연구는 없는 상황이다. 본 연구에서는 핵연료주기에 적용할 수 있는 외부비용 항목들을 도출하고 정량화를 시도하였다. 핵연료주기 외부비용 평가를 위해 고려될 수 있는 핵연료주기로 OT(직접처분), DUPIC(PWR-CANDU 연결), PWR-MOX(PWR 습식재처리), Pyro-SFR (파이로 처리와 고속로 연계)의 네 가지를 선정하였다. 원자력발전의 외부비용 평가에 고려되었던 항목들을 분석하여 핵연료주기에서 에너지 공급 안보비용, 사고위험비용과 수용성 비용을 외부비용 항목으로 도출하고 추산하였다.

• 방사성폐기물학회지
• /
• 제13권2호
• /
• pp.141-154
• /
• 2015

경수로 사용후핵연료 수송/저장용기의 핵임계 해석은 사용후핵연료내의 악티나이드핵종 및 핵분열생성물 함유량에 대한 불확실성을 이유로 신연료로 가정된 가상의 연료를 선정하여 평가해오고 있다. 그러나 이러한 평가방법은 용기 설계 시 과도한 임계여유도를 유도하여 경제적 손실을 유발할 수 있는 단점이있다. 이와 같은 단점을 극복하기 위하여 최근 연소도이득효과(burnup credit, BUC)를 반영한 수송저장용기의 설계 및 상용화를 위한 연구가 추진되었다. 이에 본 연구에서는 한국원자력환경공단에서 개발중인 금속겸용용기를 대상으로 연소도 이득효과적용 시 핵임계 안전성(criticality safety)에 영향을 미칠 것으로 예상되는 '노심 운전인자', '축방향 연소도 분포', '오장전 사고상황'에 대하여 핵임계 평가를 수행하였다. 그 결과 노심운전인자 중 저농축, 고연소도일 때 비출력에 따른 핵임계 변화가 크게 평가되었으며, 고연소도 사용후핵연료에서 End effect가 양의 값을 나타내었다. 특히 오장전에 의한 유효증배계수는 최대 0.18467증가하였으므로, 연소도이득효과를 적용 할 경우 필수고려사항임을 확인하였다. 본 연구결과는 국내모델(금속겸용용기)의 연소도 이득효과 적용기술 개발 및 사용 후핵연료 장전 시 일어날 수 있는 오장전 사고를 방지하기 위한 운영절차 개발에 참고자료로 활용될 수 있다.