• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.41-49
• /
• 2000

To understand the signal fluctuation of a wide-range oxygen sensor installed at the exhaust confluence point, when a misfiring is triggered in a cylinder, the steady state and the transient response characteristics of the sensor to the flow of the misfired gas were investigated quantitatively. It was recognized that the steady state output voltage of the sensor increased higher when it contacted the misfired gas even though the fueling condition was the same as the normal combustion case and this characteristic enabled the application of the wide-range oxygen sensor for the misfire detection. The transient response was compared at different engine speeds and it was found that the response speed increased with the engine speed. The signal fluctuation was also estimated quantitatively, using these steady state and transient response of the sensor, and the estimated signal showed satisfactory correlation with the measurements.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.173-180
• /
• 2017

정격풍속 이하에서 풍력발전기의 토크 제어기는 최대 출력 파워를 얻기 위하여 중요하다. 토크 제어의 주된 목적은 바람이 가진 에너지로부터 최대의 출력 파워를 얻도록 하는 것이다. 이를 위하여 최적모드게인을 이용하여 발전기 속도의 제곱에 비례하도록 발전기의 토크 크기를 조절하는 방법이 많이 적용되었다. 그러나 이 제어 방법은 풍력발전기가 수 MW급으로 대형화될수록 응답이 느려진다. 본 논문에서는 토크 제어기의 응답을 빠르게 하기 위하여 공력 토크의 로터 속도 비선형 파라미터를 제어 게인으로 이용하여 추가적인 토크 크기를 조절하는 방법을 고려하였다. 로터 속도 비선형 파라미터의 계산 시에 온라인 경우와 오프라인 경우를 각각 살펴보았다. 2MW 풍력발전기에 대하여 실제 난류 풍속에 대하여 수치실험을 수행하여 오프라인 경우가 출력 파워를 더 향상시키고 실용적임을 보인다.

• 한국정보전자통신기술학회논문지
• /
• 제11권5호
• /
• pp.481-486
• /
• 2018

DC 모터는 브러시 구조가 있는 DC 모터와 브러시 구조가 없는 BLDC(Brushless DC) 모터로 분류된다. BLDC 모터는 DC 모터의 브러시가 없이 정류를 전자적으로 수행하는 모터로 BLDC 모터의 속도제어를 대표하는 것은 PI 제어이다. PI 제어기를 이용한 속도제어는 정상상태에 도달하는 응답 특성이 느리다는 단점을 가지고 있다. 이를 보완하기 위해 정상 상태까지 도달하는 시간이 짧고 비선형 제어에도 쉽게 제어가 가능한 FLC(Fuzzy Logic Controller)를 이용해 전압을 가감하는 방식의 전압 제어 속도 제어기 제안하였다. 제시한 퍼지 속도 제어기의 타당성과 유용성은 MATLAB 프로그램의 Simulink를 통해 모의실험으로 입증하였다. 모의실험은 기준 속도를 500rpm, 800rpm, 1500rpm의 3가지 경우로 각각 PI 제어기와 제안한 퍼지 속도 제어기를 실험하였다. 실험 결과 제안한 퍼지 속도 제어기가 30% 정도 개선된 정상 상태 속도 응답 특성을 보이며 PI 제어기에 비해서 빠른 속도 응답 특성을 갖고 있음을 입증하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.510-513
• /
• 2009

In this paper, a novel speed control algorithm of DC motors is presented. The key contribution here is a simple speed controller only with speed feedback and without an inner current control loop. This is possible by adjusting the reference speed based on a certain rule. Therefore, the proposed speed controller here becomes simpler while maintaining the control performance. Moreover, with the proposed controller, the system response can be tuned with less complexity. This proposed control method is investigated both mathematically and experimentally.

• 한국인터넷방송통신학회논문지
• /
• 제18권3호
• /
• pp.1-7
• /
• 2018

연구의 목적은 3개 모바일 포털사이트의 응답시간을 분포를 이용하여 비교하고 분류하는 것이다. 연구대상은 Naver, Daum, Nate의 모바일 포털 사이트 접속페이지이며, 실험기간은 모바일 포털들이 활성화되기 시작되던 즈음인 2012년 4월 18일에서 2018년 4월 17일까지 6년간이다. 그리고 실험횟수는 4,060회이다. 분포비교를 위해 히스토그램과 백분율을 이용하였으며 이론적인 비교를 위해 모수적 방법인 카이스케어 검정과 비모수적 방법인 콜모고로프-스미르노프 검정을 실시하였다. 네가지 방법 모두 Naver가 가장 빨랐고, 다음이 Nate, Daum이 가장 느렸다. 평균 응답시간 면에서도 같은 결과를 낳았다. 이러한 결과는 유선 포털의 결과와 정반대로서, Naver는 매체 특성에 맞게 유선에서는 많은 콘텐츠를 무선에서는 응답시간을 높이는 전략이고, Daum은 무선에서 응답시간을 희생하면서 콘텐츠를 중시하는 전략을 구사하고 있음을 알 수 있다. 분류에서는 응답시간에 따라 "Comfortable"과 "Tolerable", "Feedback", "Leave"로 나누었으며, 이용자들이 떠날 수 있다는 7초 이상인 "Leave"의 비율이 Naver는 1.18%, Daum이 11.70%, Nate가 1.5%로 Daum이 압도적으로 높아서 Daum의 응답시간은 개선이 매우 절실한 수준임을 알 수 있다. 또한 분류 결과에 의하면 3개 모바일 포털들이 응답시간을 줄이는 것이 필요하다는 것을 밝혔다. 본 논문의 결과가 모바일 포털들의 응답시간을 줄이는 기술경쟁을 촉진할 수 있기를 기대한다.

• Wind and Structures
• /
• 제30권1호
• /
• pp.85-97
• /
• 2020

The accurate estimation of the buffeting response of a bridge pylon is related to the quality of the bridge construction. To evaluate the influence of wind field characteristics on the buffeting response of a pylon in a trumpet-shaped mountain pass, this paper deduced a multimodal coupled buffeting frequency domain calculation method for a variable-section bridge tower under the twisted wind profile condition based on quasi-steady theory. Through the long-term measurement of the wind field of the trumpet-shaped mountain pass, the wind characteristics were studied systematically. The effects of the wind characteristics, wind yaw angles, mean wind speeds, and wind profiles on the buffeting response were discussed. The results show that the mean wind characteristics are affected by the terrain and that the wind profile is severely twisted. The optimal fit distribution of the monthly and annual maximum wind speeds is the log-logistic distribution, and the generalized extreme value I distribution may underestimate the return wind speed. The design wind characteristics will overestimate the buffeting response of the pylon. The buffeting response of the pylon is obviously affected by the wind yaw angle and mean wind speed. To accurately estimate the buffeting response of the pylon in an actual construction, it is necessary to consider the twisted effect of the wind profile.

• Wind and Structures
• /
• 제9권1호
• /
• pp.1-22
• /
• 2006

The response characteristics and suppression of flow-induced vibrations of rectangular prisms with various width-to-depth ratios were experimentally investigated. The prisms were rigid and elastically mounted at both ends to enable constrained torsional vibrations only. The present study focused on torsional vibrations, one of the three types of flow-induced vibrations generated in a rectangular prism. First, the response characteristics of torsional vibrations generated in rectangular prisms were investigated by free-vibration tests. It was found that the response characteristics of torsional vibrations generated in rectangular prisms could be classified into six patterns depending on the width-to-depth ratio. Next, the response characteristics of torsional vibrations observed in the free-vibration tests were reproduced by forced-vibration tests, and the mechanisms by which the three types of flow-induced vibrations, low-speed torsional flutter, vortex excitation and high-speed torsional flutter, are generated in the rectangular prisms were elucidated on the basis of characteristics of fluid forces and visualized flow patterns. Experiments were also carried out to establish an effective method for suppressing flow-induced vibrations generated in the rectangular prisms, and it was found that low-speed torsional flutter and high-speed torsional flutter could be suppressed by placing a small normal plate upstream of the prism, which results in suppression of the alternating rolling-up of the shear layers separating from the leading edges of the prism. It was also found that vortex excitation could be suppressed by placing a splitter plate downstream of the prism, which results in suppression of the generation of wake vortices.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.986-988
• /
• 2001

This paper presents a digitally speed sensorless control system for induction motor with direct torque control (DTC). Some drawbacks of the classical DTC are the relatively large torque ripple in a low speed range and notable current pulsation during steady state. They are reflected speed response and increased acoustical noise. In this paper, the DTC quick response are preserved at transient state, while better qualify steady state performance is produced by space vector modulation (SVM). The system are closed loop stator flux and torque observer for wide speed range that inputs are currents and voltages sensing of motor terminal, model reference adaptive control (MRAC) with rotor flux linkages for the speed fuming signal at low speed range, two hysteresis controllers and optimal switching look-up table. Simulation results of the suggest system for the 2.2 [kW] general purposed induction motor are presented and discussed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.106-108
• /
• 2008

This paper deals with the design for speed controller to drive PMSM by matrix converter without DC-link circuit as the power conversion system of AC servo motor drive. To design the speed controller of PMSM drive, the closed-loop transfer function of speed controller is calculated and then the frequency-domain response characteristics are analyzed by bode plot using Matlab. Based on the results by bode plot, the speed control gains are determined. As the real effects of controller designed in the frequency-domain display in the time-domain, the performance of speed controller is confirmed by the step response of speed controller. The design examples are shown and its validity of the design method mentioned in the paper is verified through PSIM simulation.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.162-169
• /
• 2000

This study was carried out to develop a continuously variable-speed transmission(CVT) for agricultural tractor. A full-toroidal CVT mechanism with four discs and six rollers was selected as a device for changing speed ratio continuously. In the step of system layout design, the sizes of roller cylinders and end-load cylinder, which were critical factors for controlling the variator, were designed. Also the control pressure range was designed to limit the contact pressure of variator. In order to make the maximum speed of vehicle as 30km/h, the planetary gear and the six pairs of gears were designed. Also the hydraulic clutch, silent chain, hydraulic manifold and electronic controller were designed. After the design, a prototype with CVT controller was developed and tested. The speed of vehicle was changed continuously to the speed set by driver and the settling time was about 0.52 second at the step-response test (reduction ratio of variator 2.0 to 1.0), which was acceptable as a response time for working with tractor.