• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.847-854
• /
• 1989

Axial force of a V-belt CVT is investigated experimentally. The experimental results on speed ratio-torque-axial force show good agreement with the theoretical results that were obtained in the previous work. It is also found that torque capacity of the V-belt CVT increases as the axial force and the speed ratio increase. Impending slip which occurs at the maximum torque is determined via experiments for various speed ratios. Based on the impending slip region, and the theoretical curves for the speed ratio-torque-axial force relationship, an actual operating criteria for the V-belt CVT is obtained. It is suggested to use the actual operating criteria with the theoretical equations as a basic design formula for the V-belt CVT.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.89-94
• /
• 2006

The tire delivering power generated from engine to the ground pulls a vehicle to move. Radius of tires is changeable due to elasticity that depends on the speed of vehicle and traction force. The main objectives on this study are real time measurement of dynamic radius and slip ratio according to the speed and traction force. The dynamic radius is proportional to speed and traction force. According to measurement, the dynamic radius is increased about 3mm under 100km/h compared to stop. It is also increased about 1.5mm when a traction force is supplied as much as 4kN compared to no load state at low speed. There is no strong relationship between slip ratio and vehicle speed. The slip ratio is measured up to 4% under WOT at first stage gear. Through this research, the method of measuring dynamic radius and slip ratio is set up and is expected to be applied to the measurement of traction force in chassis dynamometer or accelerating and climbing ability.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2430-2434
• /
• 2011

Dynamic response is an important consideration because of the possibility of resonance according to KTX running over a railway bridges. When KTX runs over the bridge at critical speed, dynamic response is very depending on damping ratio. Current damping ratio for design of high-speed railway bridges adopted EUROCODE without verification of domestic railway bridges. The purpose of this study is to obtain the coherent damping ratio of high-speed railway bridges. Free vibration signal after KTX runs over a high-speed railway bridge was applied. The representative value from distribution of damping ratio was considered.

• Textile Coloration and Finishing
• /
• v.14 no.6
• /
• pp.335-341
• /
• 2002

The physical properties and the dyeability of the nylon S fibers Prepared by high speed spinning according to godet roller draw ratio form 1.1 to 1.6 were investigated. The strains of nylon 6 fibers were decreased against the increase of the godet roller draw ratio. The stresses of nylon 6 fibers were increased with the increase of the godet roller draw ratio. Birefringences, densities and crystallinities of the nylon 6 fibers were increased with the increase of godet roller draw ratio In DSC diagrams, the $\gamma$ form of crystal became dominant at higher godet roller draw ratio. The dye uptakes of C. 1. Acid Blue 113 on the fibers were decreased against the increase of godet roller draw ratio.

• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.380-386
• /
• 2010

This study was carried out to develop soybean thresher which is able to reduce the soybean threshing damage in comparison to the conventional thresher. A threshing cylinder with different diameter of 480 and 384 mm at each end and with one quarter disc pegs of 60 mm radius was developed and attached to the prototype thresher. A conventional thresher which has a threshing cylinder with $\wedge$ type threshing pegs and same diameter of 480 mm at each end was used for comparative test. A series of comparative performance test was conducted using sun-yu and chung-ja soybean. For sun-yu bean, which is white and usually used for soybean paste and soy sauce, the ratio of damaged beans of prototype ranged 2-3% for 330-360 rpm which is recommended cylinder speed by manufacturer. The ratio of damaged beans of conventional thresher was 3-4% for the same range of cylinder speed. chung-ja beans with black color usually shows high damaged ratio compared with white beans, thus cylinder speed of 250-300 rpm is recommended by manufacturer to reduce the damaged ratio. For this range of cylinder speed, the damaged ratio of prototype was 1.3-1.4% and it was 2.7-6.1% for the conventional thresher. Thus prototype is able to reduce the damaged ratio 1.5-5.0% compared with conventional thresher. Prototype shows 0.4% of unthreshed soybean ratio for sun-yu bean in the optimum range of cylinder speed and it was 0.87% for the conventional thresher. For chung-ja bean, the ratio of unthreshed soybean was almost same for both prototype and conventional thresher with the value of 4.0%. The reason of high unthreshed soybean ratio for chung-ja bean compared sun-yu bean is due to the high seed moisture content of 29.11% which is much higher than that of the recommended.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.92-99
• /
• 2006

The swirl ratio of a charge in the cylinder was estimated by calculating the ratio of the rotary speed of charge which could be simulated from the rotary speed of paddle in the swirl measurement apparatus, to the engine speed which could be calculated by measuring intake air flow rate. The automation of the swirl ratio measurement for cylinder head was achieved by controling both valve lift in cylinder head and a suction pressure of surge tank using two step-motors. The number of measurement position for calculating mean swirl ratio was varied by adjusting the interval of valve lift. The mean swirl ratio with varying the number of measurement position showed nearly constant value. Two measurement methods for measuring the swirl ratio were compared, one was to control the suction pressure of the surge tank with PID (proportional, integral, differential) mode with by-pass valve controlled by the step motor and the other did not control the surge tank pressure by fixing the by-pass valve. The difference of the mean swirl ratio between the two measurement methods showed nearly constant value with varying the number of measurement position. This means that the w/o PID control method could be preferred to the PID control method which has been used, due to the simpleness of the swirl measurement.

• Atmosphere
• /
• v.26 no.3
• /
• pp.461-471
• /
• 2016

A quality check algorithm for the Weather Information Service Engine pulsed Doppler wind lidar is developed from a view point of spatial and temporal consistencies of observed wind speed. Threshold values for quality check are determined by statistical analysis on the standard deviation of 3-component of wind speed obtained by a wind lidar, and the vertical gradient of horizontal wind speed obtained by a radiosonde system. The algorithm includes carrier-to-noise ratio (CNR) check, data availability check, and vertical gradient of horizontal wind speed check. That is, data sets whose CNR is less than -29 dB, data availability is less than 90%, or vertical gradient of horizontal wind speed is less than $-0.028s^{-1}$ or larger than $0.032s^{-1}$ are classified as 'doubtful', and flagged. The developed quality check algorithm is applied to data obtained at Bucheon station for the period from 1 to 30 September 2015. It is found that the number of 'doubtful' data shows maxima around 2000 m high, but the ratio of 'doubtful' to height-total data increases with increasing height due to atmospheric boundary height, cloud, or rainfall, etc. It is also found that the quality check by data availability is more effective than those by carrier to noise ratio or vertical gradient of horizontal wind speed to remove an erroneous noise data.

• Journal of Biosystems Engineering
• /
• v.21 no.2
• /
• pp.182-190
• /
• 1996

A macerating technique which can apply to the mechanical production system of the agricultural by-product was developed to increase the utilization of agricultural waste and solve the shortage problem in the forage supply for the livestock production. The macerating method is to shred the agricultural by-product by the two rolls which rotate at different speeds each other. The testing macerator was built and the optimum operating conditions are suggested. Results of this research are as follows: 1. The increase of the base roll speed and speed ratio between two rolls shows the better shredding index but decrease the drying rate. The optimum conditions of the base roll speed and the speed ratio between two rolls for the rice straw are 1200 rpm and 1.7-2.0 respectively. 2. The macerated alfalfa was dried to the 15%(w.b.) within 3 hrs in a field at speed ratio of rolls, 2:1 and base roll speed, 1800rpm. 3. The milled surface and straight knurled surface for the macerating roll have same effect on the drying rate of material. Both rolls have self-cleaning functions during operation.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.89-96
• /
• 2002

The trend of consumption of vegetable soybeans is increasing because they are recognized as the clean vegetable. The works requiring the most intensive labor are threshing and seperation ones, and they form about 80% of total labour for vegetable soybeans production. It is necessary to develop the vegetable soybeans-thresher for the sake of cost down of vegetable soybeans production. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which control the speed of threshing cylinder and the teeth gap and investigate the detachment forces. The result are as follows ; The ratio of un-threshed soybeans-pod to stem after threshing work is decreasing as the threshing cylinder speed increases: 0.0% and 2.8% at 55m/s and 18m/s of threshing cylinder speed respectively. Also the ratio of un-threshed soybeans-pod to stem is shown as 2.0% below in the condition of 64~160mm of teeth gap and over 28m/s of threshing cylinder speed. The damaged pod ratio of detached soybeans after threshing work is decreasing as the threshing cylinder speed increases: 4.8% and 1.3% at 55m/s and 18m/s of threshing cylinder speed respectively. The minimum damaged pod ratio of detached soybeans are shown as 1.0%, 1.5% and 1.9% at 18m/s, 28m/s and 37m/s of threshing cylinder speed respectively. The average detachment forces of pods are shown as 1.5kg$_{f}$ for 3 grains, 1.2kg$_{f}$ for 2 grains and 0.8kg$_{f}$ for 1 grain respectively. The maximum detachment force of pod is shown as 2.7kg$_{f}$ for 3 grains. grains.

• The Journal of the Korean dental association
• /
• v.47 no.7
• /
• pp.444-454
• /
• 2009

The purpose of this study was to compare the shaping abilities of LightSpeed, ProTaper-Universal, and hybrid technique using S-series of ProTaper-Universal and LigthSpeed. The 72 simulated root canals of J-shape were used and classified as flowing 3 groups according to the instrumentation methods; Group P of 24 canal blocks were prepared with ProTaper-Universal, Group L was prepared with LightSpeed, and Group H was prepared with hybrid technique (initial shaping with ProTaper-Universal SI and S2 and apical shaping with LightSpeed from #25 to #50). A second-year resident of Endodontic department prepared the resin block canals to apical size #50 (F5 in Group P). The time lapses for instrumentation and the reduction of root canal curvature after shaping were measured. The pre- and post-instrumented root canals were scanned and superimposed to evaluate and calculate the increased canal width and apical centering ratio. The results were as followings: Group Land H showed significant less instrumentation time than Group P (p < 0.05). The ProTaper system showed greater reduction of root canal curvature and working length diminishment than other methods (p < 0.05). LightSpeed system showed best canal curvature preserving characteristics. The Group P had greater instrumented widths at all levels examined (p < 0.05). Group L and Group H showed lower centering ratio (ability to preserve the canal center; the lower ratio means the better canal center preservation) than Group P (p < 0.05). Group H had the lowest centering ratio at the 1 mm level.