• 열처리공학회지
• /
• 제12권3호
• /
• pp.215-220
• /
• 1999

Rotary bending fatigue tests were carried out to investigate the artificial defect sensitivity of fatigue limit in annealed and austempered ductile irons. Artificial defect(hole, diameter${\leq}0.4mm$) machined on specimen surface did not bring about an obvious reduction of fatigue limit in austempered ductile iron as compared with annealed. As a result of investigation on $\sqrt{area}$ c which is the critical artificial defect size. $\sqrt{area}$ c of austempered ductile iron is larger than that of annealed. This means that the crack initiation at artificial defect in austempered ductile iron is more difficult in comparison with annealed. In case that the $\sqrt{area}$ c of artificial defect and graphite nodule are same, the rate of crack initiation for graphite nodule is higher than that of artificial defect.

• 치과방사선
• /
• 제22권1호
• /
• pp.161-168
• /
• 1992

The authors observed a 27-year-old male patient who came to the Infirmary of Kyungpook National University Hospital who had complained of dull pain in right mandibular angle area 1 month ago. As a result of careful analysis of clinical, radiological, and histopathological findings, the authors diagnosed it as Ewing's sarcoma and obtained the results as follows: 1. In clinical examination, main clinical symptoms were continuous dull pain and gingival swelling on the 2nd and 3rd molar area of the right mandible. 2. In radiographic examination, ill-defined radiolucent area was seen on mandibular right angle area, and apparent periosteal reaction of sun-ray spicule was emanated from the lingual cortex of mandibular angle area. And computed tomograph also revealed moderate-defined 3. soft tissue mass of the same area. In histopathological examination, small round-shaped, and closely packed cells with scanty cytoplasm were observed in this specimen, and positive reaction in PAS staining was also observed.

• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.167-173
• /
• 2004

Recently, it has been reported that frictional behavior at nanometer scale can be different from that at macro scale. In this article, friction and wear tests were conducted using an AFM to investigate the effect of real contact area on the coefficient of friction and wear property. SiO$_2$, Hica, and SiGe were used in friction test and the AFM tip was Si$_3$N$_4$. The real contact area between an AFM tip and flat surface was calculated by the Johnson-Kendall-Roberts (JKR) theory. Wear specimen was Mica, and the diamond tip was used. We found that the coefficient of friction is constant below a critical area, but it is degraded over the area. Moreover, it is found that wear depth increased rapidly from a certain load and was degraded as a function of the number of the scanning cycles. Also, the range of scanning velocity used in this study had little effect on the wear depth.

• KSTLE International Journal
• /
• 제4권2호
• /
• pp.47-51
• /
• 2003

Sliding wear tests have been carried out in room temperature air and water in order to compare the wear resistance of Zr-xNb-xSn alloys of various alloying elements (Nb and Sn). The main focus was to quantitatively compare the wear properties of the recently developed Zr-xNb-xSn alloys with the commercial ones using the evaluation parameters of the wear resistance with the consideration of the worn area. As a result, the recently developed alloys had a similar wear resistance compared with the commercial ones. The dominant factor governing the wear resistance was the protruded volume of the wear debris that was formed on the worn area in the air condition, but the accommodation of the plastic deformation on the contact area in water. In addition, the worn area size appeared to be very different depending on the tested alloys. To evaluate the wear resistance of each test specimen, the ratio of the wear volume or the protruded volume to the worn area ($D_e$ or $D_p$) is investigated and proposed as the evaluation parameters of the wear resistance.

• 한국지반환경공학회 논문집
• /
• 제20권1호
• /
• pp.67-74
• /
• 2019

동상은 동토지역에서 발생하는 대표적인 공학적 특성이다. 계절동토(seasonal frost area)에 해당하는 우리나라는 동결융해에 의한 구조적 피해가 발생하고 동상에 관한 연구의 필요성이 증대되고 있는 실정이다. 본 논문에서는 새롭게 개발한 투명 온도제어형 셀을 활용하여 동상에 관한 연구를 수행하였다. 동상에 민감한 흙을 인공적으로 조성하여 동상민감성 판정에 있어 중요한 인자 중 하나인 물 주입속도(water intake rate)에 관한 분석을 실시하였다. 간극수 동결에 의한 부피팽창(heave by pore water)이 수렴하는 시점 이후에 동상속도(frost heave rate)와 물 주입속도는 거의 유사하게 나타났다. 그러나 물 주입속도를 측정하기 위해 상부 페더스탈에 설치한 O-ring은 몰드 내벽과의 마찰을 발생시켜 동상발생을 저하시켰다. 따라서 물 주입속도를 활용한 동상민감성 판정 기준은 신뢰하기 힘들다고 판단되었으며, 유사한 거동을 보이는 동상속도를 활용하는 것이 적절하다는 결론을 내렸다. 또한, 동상민감성 흙을 활용해 시료크기가 동상에 미치는 영향을 파악하고자 하였다. 시료크기가 다른 2가지 경우에 대해 동상시험을 수행하였으며 상재하중, 온도구배, 그리고 건조단위중량을 동일하게 설정하였다. 실험결과를 토대로 시료크기는 동상에 영향을 미치지 않는다는 것을 발견하였다.

• 대한치과보철학회지
• /
• 제17권1호
• /
• pp.23-34
• /
• 1979

In this study, the adhesive strength of three commercial polycarboxylate cements to ten types of dental casting alloys, such as gold, palladium, silver, indium, copper, nickel, chromium, and human enamel and dentine were measured and compared with that of a conventional zinc phosphate cement. The $8.0mm{\times}3.0mm$ cylindrical alloy specimens were made by casting. The enamel specimens were prepared from the labial surface of human upper incisor, and the dentine specimens were prepared from the occulusal surface of the human molar respectively. Sound extracted human teeth, which had been kept in a fresh condition since, extraction, were mounted in a wax box with a cold-curing acrylic resin to expose the flattened area. The mounted teeth were then placed in a Specimen Cutter (Technicut) and were cut down under a water spray, and then the flat area on the all specimens were ground by hand with 400 and 600 grit wet silicone carbide paper. Two such specimens were then cemented together face-to-face with freshly mixed cement, and moderate finger pressure was applied to squeeze the cement to a thin and uniform film. All cemented specimens were then kept in a thermostatic humidor cabinet regulated at $23{\pm}2^{\circ}C.$ and more than 95 per cent relative humidity and tested after 24 hours and 1 week. Link chain was attached to each alloy specimen to reduce the rigidity of the jig assembly, and then all the specimens were mounted in the grips of the Instron Universal Testing Machine, and a tensile load was delivered to the adhering surface at a cross head speed of 0.20 mm/min. The loads to which the specimens were subjected were recorded on a chart moving at 0.50 mm/min. The adhesive strength was determined by measuring the load when the specimen separated from the cement block and by dividing the load by the area. The test was performed in a room at $23{\pm}2^{\circ}C.$ and $50{\pm}10$ per cent relative humidity. A minimum of five specimens were tested each material and those which deviated more than 15 per cent from the mean were discarded and new specimens prepared. From the experiments, the following results were obtained. 1) It was found that the adhesive strength of the polycarboxylate cement to all alloys tested was considerably greater than that of the zinc phosphate cement. 2) The adhesive strength of the polycarboxylate cements was superior to the non precious alloys, such as the copper, indium, nickel and chromium alloys, but it was inferior to the precious gold, silver and palladium alloys. 3) Surface treatment of the alloy was found to be an important factor in achieving adhesion. It appears that a polycarboxylate cement will adhere better to a smooth surface than to a rough one. This contrasts with zinc phosphate cements, where a rough helps mechanical interlocking. 4) The adhesion of the polycarboxylate cement with enamel was found superior to its adhesion with dentine.

• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.63-67
• /
• 2016

본 논문에서는 폴리머 기반의 유연 기판 위 적층 된 다양한 필름의 굽힘 탄성계수의 간접 측정법을 소개한다. 패키징 기판의 다양한 적층 재료들의 탄성계수는 기계적으로 신뢰성 있는 전자기기 개발에 결정적이지만, 기판과 매우 견고히 접합하고 있는 적층 필름을 온전히 떼어 내어 자유지지형(free-standing) 시편을 만들기 어렵기 때문에 그 측정이 쉽지 않다. 이를 해결하기 위해 본 연구에서는 필름-기판의 복합체 시편에 대한 3점 굽힘을 진행하였고 시편 단면에 면적 변환법(area transformation rule)을 적용한 응력 해석을 수행하였다. 탄성계수를 알고 있는 기판에 대하여, 굽힘 시험으로 얻은 다층 시편의 강성으로부터 필름과 기판의 탄성계수 비를 계산하였으며, 전기 도금 구리 시편을 이용하여 양면 적층, 단면 적층의 두 가지 해석 모델이 실험 평가되었다. 또한 주요 절연체 적층 재료인 prepreg (PPG)와 dry film solder resist (DF SR)의 굽힘 탄성계수가 양면 적층 시편 형태로 측정 되었다. 결과로써 구리 110.3 GPa, PPG 22.3 GPa, DF SR 5.0 GPa이 낮은 측정 편차로 측정 됨으로써 본 측정법의 정밀도와 범용성을 검증하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 봄 학술발표회 논문집
• /
• pp.73-78
• /
• 1993

This study was performed for the purposes of estimating steel corrosion of concrete structures under the environment of seawater. The corrosion of steel was accelerated in artificial seawater with seven kinds of specimen which was embedded in mortar. By measuring choride content in mortar, half cell potential and corrosion area ratio, the degree of steel corrosion can be assumed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.569-576
• /
• 2000

This study performs a series of Triaxial Compression Test for clay-sand composite specimens changing area replacement ratio. Purpose of the test is to conform the propriety of weighted average method in estimating shear strength of the composite ground. The test results show that measured values of shear strength of composite specimens are larger by 20∼30% than those from estimation using the current weighted average method. It is thought that the differences are from pseudo-overconsolidation behavior of composite specimens.

• 항공우주시스템공학회지
• /
• 제7권1호
• /
• pp.39-43
• /
• 2013

In this study, damage assesment and repair technique of aircraft adopted on Sandwich composite structure were performed. The sandwich composite structure were damaged by drop weight type impact test machine. The damaged sandwich composite structure was repaired using external patch repair method after removing damaged area. This study presents comparison results of the experimental investigation between the impact damaged and the repaired specimen.