• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.176-184
• /
• 1996

To overcome the drawbacks of conventional LDMOSFETs, we propose RESURF EDMOSFETs which can be adapted in varous circuit applications, be driven without charge pumping circuity and thowe threshold voltage can be adjusted. The devices have the diffused drift region formed by a high tmperature process before the gate oxidaton. After the polysilicon gate electrode formation, a fraction of the drift region around the gate edge is opened for supplemental self-aligned ion implantation to obtain self-aligned drift region. This leads to a shorter gate length and desirable drift region junction contour under the gate edge for minimum specific-on-resistance. In additon, a and maximize the breakdown voltage. Also, by biasing the metal field plate, we can reduce the specific-on-resistance further. The devices are optimized by using the TSUPREM-4 process simulator and the MEDICI device simulator. The optimized devices have the breakdwon voltage and the specific-on-resistance of 101.5V and 1.14m${\Omega}{\cdot}cm^{2}$, respectively for n-channel RESURF EDMOSFET, and 98V and 2.75m.ohm..cm$^{2}$ respectively for p-channel RESURF EDMOSFET. To check the validity of the simulations, we fabricated n-channel EDMOSFETs and confirmed the measured breakdown voltage of 97V and the specific-on-resistance of 1.28m${\Omega}{\cdot}cm^{2}$. These results are superior to those of any other reported power devices for smart power IC applications.

• Journal of Ocean Engineering and Technology
• /
• v.1 no.2
• /
• pp.93-100
• /
• 1987

Corrosion fatigue cracking of the austenitic stainless steel(bese metal & heat affected zone by TIG weld) was studied experimentally under the environments of various specific resistance and air. The characteristics of corrosion fatigue crack growth rate and the environmental constants of paris' rule were investigated for SUS 304 weldments in the various specific resistance. The influences of stress intensity factor range and corrosion on the crack growth rate were compared. The characteristics of corrosion fatigue cracking for the weldments were inspected from mechanical, electrochemical and microstructural point of view. Main results obtained are as follows: 1) As the specific resistance decreases, the environmental constant C of paris'rule increases(hence the corrosion fatigue crack growth rate is rapid), but the environmental constant m decreases, so the effect of corrosion to the crack growth rate is more susceptible than thet of stress intensity factor range. 2) As the stress intensity factor range decreases, the corrosion fatigue crack growth rate of heat affected zone is more susceptible than that of the base metal. 3) The corrosion fatigue crack growth rate of the heat affected zone is more rapid than that of the base metal, because of the phenomenon of softening and the less noble potential coused by wedlding heat cycle. 4) The corrosion fatigue cracking of SUS 304 weldment appears transgranular fracture.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.23-28
• /
• 2020

In general, lithography techniques are applied when machining single-crystal silicon in nanoscale applications; however, these techniques involve low degrees of freedom for the vertical shapes. By applying mechanical techniques to machine silicon, nanopatterns having various types of vertical shapes can be manufactured. In this study, we determined the ductile-brittle machining transition point and analyzed the- variation of the specific cutting resistance within the ductile machining region in nanoscale applications. When brittle fracture occurred during the nanoscale cutting, the depth of cut and cutting force increased and decreased rapidly, respectively. The first point of rapid increase in the depth of cut was defined as the ductile-brittle machining point. Subsequently, the shape of the machining tool was observed using a scanning electron microscope to calibrate the machining area, considering the tip blunting. The specific cutting resistance decreased continuously and converged to a certain value during the nanoscale cutting. The decrease and convergence in the value can be attributed to the decrease in the ratio of the arc length to the area of the machining tool and silicon.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.22-27
• /
• 2008

Analytical models for breakdown voltage and specific on-resistance of 4H-silicon carbide Schottky diodes have been derived successfully by extracting an effective ionization coefficient $\gamma$ from ionization coefficients $\alpha$ and $\beta$ for electron and hole in 4H-SiC. The breakdown voltages extracted from our analytical model are compared with experimental results. The specific on-resistance as a function of doping concentration is also compared with the ones reported previously. Good fits with the experimental results are found for the breakdown voltage within 10% in error for the doping concentration in the range of about $10^{15}{\sim}10^{18}\;cm^{-3}$. The analytical results show good agreement with the experimental data for the specific on-resistance in the range of $3{\times}10^{15}{\sim}2{\times}10^{16}\;cm^{-3}$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.64-72
• /
• 2014

In the past, prism patterns have been linear triangular shapeswith a $90^{\circ}$ angle; however, new micro prism patterns having acute angles or obtuse angles have recently been the subject of demandin the display, lighting and photovoltaic industries. Micro-cutting experiments for micro-prism patterns having $60^{\circ}$, $90^{\circ}$, and $120^{\circ}$ angles on an electroplated Ni mold were performed and it was found in this study that the specific cutting resistance increased with a decrease in the tool angles (prism pattern angles). The cause of this variation had been thought to be the increase of the ploughing force due to tip rounding and the friction force due to the edge effect. However, the depth of the cut was large enough that it was possible to neglect these effects. Therefore, this study introduced the concept of representative stress of indentation. The measured stress was varied according to the indentation depth eventhoughthetestedspecimenswereidentical ; the varied stress was termed the representative stress. According to indentation theory, the strain that the Ni mold experienced increased with a decrease in the tool angle. Based on the stress-strain relationship, higher strain means higher stress and higher specific cutting resistance. Therefore, the specific cutting resistance was higher at smaller tool angles that had higher strain and stress.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.76-76
• /
• 1999

Low resistance ohmic contacts to the Si-doped InGaN(~$\times$10$^{19}$ ㎤) were obtained using the W metallization schemes. Specific contact resistance decreased with increasing annealing temperature. The lowest resistance is obtained after a nitrogen ambient annealing at 95$0^{\circ}C$ for 90s, which results in a specific contact resistance of 2.75$\times$10$^{-8}$ Ω$\textrm{cm}^2$. Interfacial reactions and surface are analyzed using x-ray diffraction, transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The X-ray diffraction results show that the reactions between the W film and the InGaN produce a $\beta$-W$_2$N phase at the interface. TEM results also show that the $\beta$-W$_2$N has a rough interface, which increase contact area. It shows that the morphology of the contacts is stable up to a temperature as high as 95$0^{\circ}C$. Possible mechanisms are proposed to describe the annealing temperature dependence of the specific contact resistance.

• Journal of Power System Engineering
• /
• v.6 no.1
• /
• pp.74-81
• /
• 2002

The characteristics of corrosion resistance for the surface of ductile cast iron(GCD40) by plasma nitriding process have been studied in terms of electrochemical polarization behaviors including corrosion potential($E_{corr}$), anodic polarization trends, polarization resistance($R_p$), and also have been studied microstructures, hardness and specific wear of nitrided layer Nitrided layer showed an enhanced hardness values in all the plasma nitriding condition investigated. In the result of wear test, specific wear of nitrided specimens were much decreased than that of non-treated specimens. In the results of XRD, ${\gamma}'phase\;and\;{\varepsilon}$ phase were detected in nitrided surface. And it was found that ${\varepsilon}$ phase was decreased and ${\gamma}'phase$ was increased respectively, as the nitriding time became longer. In the test of corrosion resistance, natural potentials in all the nitrided specimens were towards noble directions than in the case of non-treated specimens. The measurement of electrode potentials revealed that corrosion resistivity of plasma nitrided specimens were higher than in the case of the non-treated specimens.

• Applied Chemistry for Engineering
• /
• v.27 no.2
• /
• pp.210-216
• /
• 2016

In this paper, the electrical and resistance heating properties of carbon fiber heating elements with different electroless Ni-P plating times for car seat were studied. The specific resistance and specific heat of the carbon fibers were determined using 4-point probe method and differential scanning calorimetry (DSC), respectively. The surface morphology and temperature of carbon fibers were measured by scanning electron microscope (SEM) and thermo-graphic camera, respectively. From experimental results, the nickel layer thickness and surface temperature of carbon fibers increased with increasing the plating time. However, the specific heat and specific resistance decreased with respect to the increased plating time. In conclusion, the electroless Ni-P plating could improve the resistance heating and electrical properties of carbon fiber heating elements for car seat.

• Membrane Journal
• /
• v.8 no.3
• /
• pp.130-137
• /
• 1998

Membrane fouling characteristics in the membrane-coupled activated sludge system were investigated. The influence of the floc size variation on the filtration resistance was analyzed using resistance-in-series model and mixed liquor was fractionated into three components to verify which component would give rise to a major contribution to the total resistance. The microbial floc size was rapidly reduced during the initial 4~6 hours of operation, and then decreased slightly but steadily, followed by leveling off at the size of 20 $\mu$m. The specific resistance of activated sludge increased with operation time, and measured values of specific resistance were matched well with the values estimated on the basis of the mean particle size in the mixed liquor. The contribution of soluble organics and cells to the total resistance was relativdy small compared with that of the supematant. Colloidal particles in the supematant showed much higher specific resistance than that of microbial floc, and played the most important role in the cake resistance.

• Journal of Industrial Technology
• /
• v.36
• /
• pp.83-88
• /
• 2016

In this study, a series of experiment was carried to improve dewaterability of the sludge produced in a treatment plant, located in Hongcheon, Gangwondo, which has been treating municipal wastewater and livestock wastewater. Optimum sludge mixing ratio and the amount of sludge conditioner were determined. As sludge conditioners, alum and ferric salt were selected and tested. For the measurement of sludge dewaterability, capillary suction time(CST) and the specific resistance were measured, The specific resistance was detemined by running a series of Buchner Funnel Test. Mixing the two sludges at a 50:50 ratio with the addition of 20 mL alum gave the best results in terms of dewaterability. The moisture content decreased by 2% at this condition.