• 한국표면공학회지
• /
• 제57권2호
• /
• pp.105-114
• /
• 2024

Tempering behavior and mechanical properties in AISI H13 steel, quenched and tempered from 300 ℃ to 700 ℃ for different tempering time (1, 2, 5, 10, 20 hr) were quantitatively investigated by scanning electron microscopy (SEM), x-ray diffractometer (XRD), impact test machine, rockwell apparatus, ball-on-disk tester. Under the condition that the tempering time is 2 hours, the hardness increases slightly as the tempering temperature increases, but decreases rapidly when the tempering temperature exceeds 500 ℃, while the impact energy increases in proportion to the tempering temperature. Friction tests were conducted in dry condition with a load of 30 N, and the friction coefficient and wear rate according to tempering conditions were measured to prove the correlation with hardness and microstructure. In addition, primary tempering from 300 ℃ to 700 ℃ was performed at various times to establish a kinetic model to predict hardness under specific tempering conditions.

• Advances in Automotive Engineering
• /
• 제1권1호
• /
• pp.21-39
• /
• 2018

Clutch energy is the thermal energy dissipated on the clutch disc, and it reaches its highest level during drive-off as a result of the difference between the angular speeds of the flywheel and clutch disc, and the torque transmitted. The thermal energy dissipated effects the clutch life. This study presents a new drive-off and thermal model to calculate the clutch energy for a rear wheel driven heavy-duty vehicle and to analyze the effects of clutch energy on temperatures of clutch pressure plate, flywheel and clutch housing. Three different driver profiles are used, based on the release of the clutch pedal in modulation zone: i) the pedal travels with the same speed all the way, ii) the travel speed of the pedal increases, iii) the travel speed of the pedal decreases. Vehicle test is performed to check the accuracy of the model. When compared to a simpler model that is widely used in the literature to calculate the clutch energy, the model used in this study calculates the clutch energy and angular speed behaviors of flywheel and transmission input shaft in better agreement with experimental results. Clutch wear and total clutch life are also estimated using the mean specific friction power.

• 한국전산구조공학회논문집
• /
• 제22권1호
• /
• pp.105-115
• /
• 2009

휨거동을 하는 전단벽을 대상으로 동일한 총 단면적을 갖는 1개의 전단벽과 마찰형 감쇠기로 연결된 전단벽의 내진성능을 수치해석을 통해 비교하였다. KBC 2005 설계스펙트럼을 근거로 축소 조절한 7개의 지진파를 입력하중으로 마찰형 감쇠기가 설치된 전단벽의 평균응답을 분석하였다. 마찰형 감쇠기의 중요한 설계변수인 기준 마찰력인 슬립하중은 각층의 마찰형 감쇠기 위치에 생기는 수직방향 전단력의 총합의 5, 10, 20, 30, 60, 90%값으로 하여 슬립이 특정한 층에 편중되지 않도록 하였다. SeismoSturct 프로그램을 이용해 비선형시간이력 해석을 수행하여 밑면 전단력, 에너지 소산량, 1층 벽체곡률, 최상층변위 측면에서 마찰 감쇠기의 제진성능을 분석하였다. 기준마찰력의 30%이하 수준의 총 마찰력을 갖는 마찰 감쇠기가 우수한 제진성능을 보였다.

• Structural Engineering and Mechanics
• /
• 제48권3호
• /
• pp.367-382
• /
• 2013

Different types of long slender pile shall buckle with weak soil and liquefied stratum surrounded. Different from considering single side earth pressure, it was suggested that the lateral earth pressure can be divided into two categories while buckling: the earth pressure that prevent and promotes the lateral movement. Active and passive earth pressure calculation model was proposed supposing earth pressure changed linearly with displacement considering overlying load, shaft resistance, earth pressure at both sides of the pile. Critical buckling load calculation method was proposed based on the principle of minimum potential energy quoting the earth pressure calculation model. The calculation result was contrasted with the field test result of small diameter TC pile (Plastic Tube Cast-in-place pile). The fix form could be fixed-hinged in the actual calculation assuring the accuracy and certain safety factor. The contributions of pile fix form depend on the pile length for the same geological conditions. There exists critical friction value in specific geological conditions that the side friction has larger impact on the critical buckling load while it is less than the value and has less impact with larger value. The buckling load was not simply changed linearly with friction. The buckling load decreases with increased limit active displacement and the load tend to be constant with larger active displacement value; the critical buckling load will be the same for different fix form for the small values.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.904-907
• /
• 2002

Optical disk drive device is improved in rotating speed for faster data reading. In the case of CD-ROM, rotating speed is over 10000 rpm in the practical use. As a result of high rotating speed, unexpected effects as like increasing disk fluctuation and acoustic noise are raised by the air friction on the rotating disk and the eccentricity of rotating parts. The overall acoustic noise of running CD-ROM could be classified into two different characterized noise. The first is the structural-borne noise which is generated from vibrating solid body. By the reason, the signal of structural borne noise has very similar to the signal of surface vibrating one. It has dense noise energy at specific frequency region. The other is the air-borne noise which is generated from turbulence or vortex caused by friction between disk and air. The signal of air-borne noise has no dominant peak point at acoustic pressure-frequency domain. The noise energy is widely distributed while comparatively high and large frequency region. The structural-borne noise could be reduced by reducing vibration of structure and in addition it's target reducing frequency is narrow. However the air-borne noise reduction is effectively needed of enclosing method for the noise source located near the disk surface because it is difficult to define target frequency point. In this study, the acoustic noise at driving CD-ROM is classified by the sides of it's character and tried to reduce the overall acoustic noise.

• Tribology and Lubricants
• /
• 제23권1호
• /
• pp.1-8
• /
• 2007

Turbocharger bearings are under the circumstance of high temperature, moreover rotated at high speed. It is necessary to be designed to overcome the high temperature. So the type of oil inlet port, the inlet oil temperature and the sort of engine oil should be designed, controlled and selected carefully in order to reduce the bearing inside temperature. Therefore, in this study, the effects of the type of inlet oil port, inlet temperature and the sort of engine oil on the performance of a turbocharger bearing are to be investigated. It is found that the type of oil inlet ports, the control of inlet oil temperature and the selection of engine oil type play important roles in determining the temperature and pressure, then the friction and load of a turbocharger journal bearing at high speed operation.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.77-82
• /
• 2003

In end milling process, undeformed chip thickness and cutting force vary periodically with phase change of the tool. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting to this. In the current study, the varying undeformed chip thickness and the cutting forces in a down-end milling process have been replaced with the equivalent ones of oblique cutting. And, the down-end milling characteristics of SM45C has been compared with that of the up-end milling previously presented with different helix angles.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.294-299
• /
• 2005

In order to control indoor air quality and save energy. it is needed to install a suitable ventilation system equipped with heat exchanger for heat recovery. Paper heat exchanger can recover $50{\sim}70$ of the enthalpy difference between supply and exhaust air. The purpose of this research is to obtain the experimental correlations for the friction factor, heat transfer coefficient, mass transfer coefficient and permeance of paper heat exchanger, which can be used for the performance prediction of the paper heat exchanger. Pressure drop at various velocities and heat transfer rate at various dry-bulb temperatures, relative humidities, and specific humidities are measured to make experimental correlations. The results of prediction using correlations show fairly good agreement with experimental data.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.72-80
• /
• 1995

Ultraprecision machining technology has been playing a rapidly increasing and important role in manufacturing. However, the physics of the micromachining process at very small depth of cut, which is typically 1 .mu. m or less is not well understool. Shear along the shear plane and friction at the rake face dominate in conventional machining range. But sliding along the flank face of the tool due to the elastic recovery of the workpiece material and the effects of plowing due to the large effective negative rake angle resultant from the tool edge radius may become important in micromachining range. This paper suggests an orthogonal cutting model considering the cutting edge radius and then quantifies the effect of plowing due to the large effective negative rake angle.

• 한국터널지하공간학회 논문집
• /
• 제20권1호
• /
• pp.161-182
• /
• 2018

본 연구에서는 퇴적층 암석에서 픽 커터의 절삭성능을 평가하기 위하여 선형절삭시험을 수행하였다. 중국에서 채취된 Linyi사암과 역암을 모사한 콘크리트를 시험체로 사용하였다. 소규모 선형절삭시험장비를 이용하여 다양한 절삭조건하에서 절삭조건에 따른 커터작용력과 비에너지의 변화양상을 평가하였다. 커터작용력은 두 가지 재료 모두에서 압입깊이와 커터간격이 증가함에 따라 증가하는 경향을 나타내었고 재료의 강도에 영향을 받는 것으로 나타났다. 반면 최대작용력과 평균작용력의 비율은 재료의 강도에 영향을 받기 보다는 재료의 구성 물질과 절삭특성에 영향을 받는 것으로 판단되었다. 절삭계수는 암석과 픽 커터의 마찰 특성에 영향을 받으나 절삭조건에는 영향을 받지 않는 것으로 나타났다. 따라서 절삭계수와 픽 커터 작용력의 합력방향에 따라 암석의 특성을 고려한 최적의 절삭각도를 선정해야 할 것으로 판단되었다. 한편 절삭조건에 따른 비에너지의 변화양상으로부터 최적 절삭조건을 규명하였다. 두 가지 재료에서 최적 s/p비는 2~4 범위로 도출되었고, 압입깊이가 증가함에 따라 비에너지는 감소하는 경향을 나타내었다. 본 연구의 결과는 픽 커터의 절삭메커니즘 규명을 위한 데이터베이스로 활용될 수 있으며, 픽 커터를 사용한 기계굴착장비의 설계에 활용될 수 있을 것으로 기대된다.