• Journal of the Korean Wood Science and Technology
• /
• 제18권4호
• /
• pp.65-78
• /
• 1990

For the purpose of Improving the sounding boards for the conventional GAYAKUM, I was making approximately 202 specimens of radial board, 371 specimens of tangential board by cutting along the grain and the part of stem and 31 specimens of the disjointed traditional GAYAKUM made in Paulownia coreana. And it was conducted to measure specific gravity, dynamic Young's modulus, internal friction, resonant frequency, velosity of sound and width of annual ring by the method of the frexural vibration in a free-free bar in the audio frequency range. And it confirmed the juvenile wood by measuring wood fiber length of specimens. It was also conducted to investigate dynamic properties and moisture absorption by various heat-treatment and to test dynamic Young's modulus and internal friction for the disjointed conventional GAYAKUM. The results obtained were summarized as follow: 1. The Juvenile wood is located within about 7 annual rings from the pith in Paulownia coreana. 2. As increased with the specific gravity, the dynamic Young's modulus had more and more increased, but the internal friction had slightly decreased. 3. I think that radial board would be good for sounding board wood. because radial board is higher than tangential board in dynamic Young's mudulus and internal friction is lower than tangential board. 4. The value of mean dynamic Young's modulus on the conventional GAYAKUM, radial board and tangential board of 604 samples is $0.4283\pm0.037(\times10^{11}dyne/cm^2)$, $0.4316\pm(\times10^{11}dyne/cm^2)$ and $0.4234\pm0.112(\times10^{11}dyne/cm^2)$ respectively. The value of the radial board showed little higher than that of conventional GAYAKUM, but It had a similar tendency between conventional GAYAKUM and tangential board. 5. The annual ring width by four aspect is more narrow in north and west than that of others. 6. The values of specific gravity and dynamic Young's modulus in the mature wood showed higher than those of juvenile wood. 7. As the grain angle in the butt wood more increased to bark from pith, the dynamic Young's modulus were low. Then it was not good for sounding board. 8. It appeared that the heat-treatment for sounding board wood had a more effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature. 9. As increased with the temperature, the rate of moisture absorption of heat-treatment wood had decreased. In conclusion, I thought that the sounding board wood for GAYAKUM would had the most effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature using the radial board of mature wood.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.245-250
• /
• 1998

The Elastic modulus depends on the elastic property of composition materials, the gravity of aggregate, the bond strength of binder, the usage and quantity of admixture, curing and measuring method, etc. Accordingly, the aim of this study, by manufacturing concrete of practical high strength range(600~ 1000kg/$\textrm{cm}^2$) with the specific cement and mineral admixtures, is to compare elastic modulus with the existing equations and also to estimate elastic property of use materials. As a result, it could be confirmed that the existing equations which were proposed by the ACI 363, CEB-FIP Code, and New-RC have a tendency to the overestimation in general. However, it could be confirmed that the KCI-96 and Norwegian NS 3473 equations are closed to measuring results, and that the elastic modulus property have a different tendency due to types of cements.

• 한국염색가공학회지
• /
• 제27권3호
• /
• pp.165-174
• /
• 2015

To develop automobile parts, the unsaturated polyester based matrix resin(PR)/reinforcement(randomly oriented chopped E-glass fiber, GF) composites were prepared using sheet molding compound(SMC) compression molding. The effects of GF length(0.5, 1.0 1.5 and 2.0inch)/content (15, 20, 25, 30wt%) and number of ply(3, 4 and 5) on the specific gravity and mechanical properties of PR/GF composites were investigated in this study. The optimum length of GF was found to be about 1.0inch for achieving improved mechanical properties(tensile strength and initial modulus). The tensile strength and initial modulus of composites increased with increasing GF content up to 30wt%, which is favorable content range for SMC. The specific gravity, tensile strength/initial modulus, compressive strength/modulus, flexural strength/modulus and shear strength increased with increasing the number of ply up to 5, which is the maximum number of ply range for SMC. The effectiveness of ply number increased in the flexural strength > shear strength > compressive strength > tensile strength.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.347-351
• /
• 2004

[ $Si_3N_4$ ] composites have been extensively studied for engineering ceramics, because it has excellent room and high temperature strength, wear resistance properties, good resistance to oxidation, and good thermal and chemical stability. In the present work, carbon short fiber reinforced $Si_3N_4$ ceramics were fabricated by hot press method in $N_2$ atmosphere at $1800^{\circ}C$ using $Al_2O_3\;and\;Y_2O_3$ as sintering additives. Content of carbon short fiber was $0\%,\;0.1\%\;and\;0.3\%$. The composites were evaluated in terms of density, flexural strength and elastic modulus through the 3-point bending test at room temperature. Also, The wear behavior was determined by the pin on disk wear tester using silicon nitride ball. Experimental density and flexural strength decreased with increasing content of carbon fiber. But specific modulus increased with increasing content of carbon fiber. In addition, friction coefficient and specific wear loss decreased with increasing content of carbon short fiber by reason of interfacial defects between matrix and fiber.

• Journal of the Korean Wood Science and Technology
• /
• 제16권1호
• /
• pp.21-44
• /
• 1988

팔만칩 및 톱밥을 보오드에 활용(活用)하기 위한 방안(方案)의 하나로, 이들의 취약한 처리(物理) 및 기계적(機械的) 성질(性質)을 개선(改善)시키기 위하여 비목질재료(非木質材料)인 폴리프로필렌망(網)을 결체(結締)하여 보오드를 제조(製造)하였다. 보오드의 제조조건(製造條件)은 비중(比重)을 0.40, 0.55, 0.70 및 0.85의 4수준으로 하고 수지첨가율(樹脂添加率)을 8%, 10%, 12% 및 14%의 4수준으로 하였으며, 망수(網數)는 1장에서 4장으로 하여 보오드를 각각 제조(製造)하였다. 이들 보오드의 물리(物理) 및 기계적(機械的) 성질(性質)은 두께팽창율(膨脹率), 휨파괴계수(破壞係數), 휨탄성계수(彈性係數), 인장강도(引張强度), 박리저항(剝離抵抗) 및 나사못보지력(保持力) 등을 측정조사(測定調査)하고 고찰(考察)하였는데 본연구(本硏究)에서 얻은 중요한 결론(結論)은 다음과 같다. 1) 지수첨가율(指數添加率)이 증가함에 따라 두께팽창율(膨脹率)은 감소(減少)하였고, press-lam 보오드는 일반성형(一般成形)보오드 보다 낮은 값을 보여 주었다. 2) 보오드의 휨파괴계수(破壞係數) 및 탄성계수(彈性系數)는 비중(比重)이 증가하였으며 press-lam 보오 드는 일반적형(一般的形)보오드보다 높은 값을 나타내었다. 망수(網數)가 증가함에 따라 휨파괴계수(破壞係數)는 증가하였고, 수지첨가율(樹脂添加率)이 증가함에 따라서도 같은 양상이 나타났으나 휨탄성계수(彈性係數)의 경우 망수(網數)에 따른 효과(效果)는 나타나지 아니하였다. 3) 비중(比重)이 증가함에 따라 보오드의 인장강도(引張强度)는 증가하였으며, 망구성(網構成)보오드는 대조보오드보다 높은 값을 나타내었다. 또 망수(網數)가 증가함에 따라서도 인장강도(引張强度)는 증가하였으며, press-lam 보오드는 일반적형(一般的形)보오드보다 높은 인장강도치(引張强度値)를 보여 주었다. 4) 보오드의 박리저항(剝離抵抗)은 비중(比重)이 증가함에 따라 증가하였으며 망(網)을 결체(結締)한 보오드는 대조보오드 보다 모두 낮은 값을 보여 주었다. 기수매구성(奇數枚構成)보오드는 우수매구성(偶數枚構成)보오드보다 낮은 박리저항치(剝離抵抗値)를 보였다. 5) 수지첨가율(樹脂添加率) 및 비중(比重)이 증가함에 따라 나사못 보지력(保持力)은 증가하였으나, 망구성(網構成)보오드와 대조보오드사이에서의 차이는 크지 아니하였다. presslam 보오드에서 팔만칩보오드의 경우 고비중(高比重)보오드가, 톱밥보오드의 경우 저비중(低比重)보오드가 각각 대조보오드보다 높은 값을 보여 주었다.

• Journal of applied mathematics & informatics
• /
• 제42권2호
• /
• pp.391-398
• /
• 2024

This article explains how solitons propagate when there is a detuning factor involved. The explanation is based on the nonlinear complex Ginzburg-Landau equation, and we first consider this equation before systematically deriving its solutions using Jacobian elliptic functions. We illustrate that one specific ellipticity modulus is on the verge of occurring. The findings from this study can contribute to the understanding of previous research on the Ginzburg-Landau equation. Additionally, we utilize Jacobi's elliptic functions to define specific solutions, especially when the ellipticity modulus approaches either unity or zero. These solutions correspond to particular periodic wave solitons, which have been previously discussed in the literature.

• 지질공학
• /
• 제26권4호
• /
• pp.593-600
• /
• 2016

본 연구에서는 국내의 107개 터널 설계 과정에서 수행한 현장 및 실내시험 자료 4,280개를 이용하여 암반 및 무결암의 역학적 특성을 암종 및 강도별로 분석하였다. 분석된 물리 및 역학적 특성은 단위중량, 점착력, 내부마찰각, 변형계수, 탄성계수, 포아송비, 일축압축강도, 인장강도, 투수계수, 비중이다. 평균값의 분석 결과에 의하면 편마암은 비중, 화강암은 투수계수, 퇴적암은 단위중량과 점착력, 내부마찰각, 화산암은 변형계수와 탄성계수, 일축압축강도, 인장강도, 변성암은 포아송비에서 가장 높은 값을 보인다. 역학적 특성의 분포 범위는 암종 및 강도를 고려한 분석에도 불구하고 넓게 분포하며, 이는 암반의 불균질성과 이방성에 기인하는 것으로 판단된다.

• 한국세라믹학회지
• /
• 제13권1호
• /
• pp.35-44
• /
• 1976

The effect of quartz which exists in clays, especially in kaolin used for the production of chamotte sagger, on the strength of refractory was examined. In this study, a mixture of chamotte 50%, kaolin 25%, plastic clay 25% in ternary component system was selected as a batch composition. To this mixture 1%, 3% and 5% of feldspar and sericite were added respectively. The plastic clay used here was separated under 170 mesh by dry process. Feldspar and sericite were separated under 325 mesh by dry process. Feldspar and sericite were separated under 325 mesh by dry process. In order to change the particle size and the content of quartz, the kaolin was separated under 60, 115, 170 and 325 mesh by wet process, substituted quartz for coarse parts of it. Chamotte was classified into three grades, coarse (5-10mesh): medium (10-20mesh): fine(20-115mesh) and the ratio was 1:1:1. Samples were formed in 0.8xIx10cm size with 12.5% water at 160kg/$\textrm{cm}^2$ pressure, and fired at 130$0^{\circ}C$ for 1 hr. The fired samples were ivnestigated by means of x-ray diffraction analysis and microscopic observation, and the physical properties of them were also examined, such as firing shrinkage, apparent specific gravity and bulk specific gravity, apparent porosity, water absorption and modulus of rupture. The obtained results are as follows: 1. When screened kaolin with low content of quartz was added to fixed chamotte-plastic clay system, the sample lowered modulus of rupture and increased apparent porosity as the size of kaolin became finer. 2. When kaolin under 325 mesh with 7.2-15.81% quartz between 60-325 mesh was added to fixed chamotte-plastic clay system, the sample had higher apparent porosity and lower modulus of ruputure as the size and the amount of quartz became larger. 3. The addition of feldspar and sericite to chamotte-plastic clay system improved apparent porosity and modulus of rupture. The effect of feldspar was better when quartz content was low, although that of sericite was better than quartz content was high.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.425-428
• /
• 2006

In order to estimate the reduction of laodbearing capacity, followed by the attributive change of heat while high strength concrete structure is revealed on fire it is necessary to evaluate, it is necessary to evaluate the property of material under high temperature such as thermal conductivity, specific heat, compressive strength, modulus of rigidity and diminution figure. Therefore, this study is for the purpose of presenting evaluation data for the analysis of thermal behavior about the high strength concrete material under high temperature, through the experiment by manufacturing concrete(40, 50, 60, 80, 100 MPa) commonly used in the construction field. As a result of the study, in the case of physical attribute, it demonstrates a greater fluctuation of change than the one of 30 MPa concrete. In case of specific heat, the high strength concrete, shown the serious diminution between $500{\sim}600^{\circ}C$, presents the thermal change area corresponding to the change of high strength concrete. In compressive strength, regardless of intensity of concrete, all of them show the first intensity loss between normal temperature and $100^{\circ}C$, the dramatic loss beyond $400^{\circ}C$. The concrete weighing above 50 MPa shows a twice lower dramatic intensity loss than the one weighing $30{\sim}40MPa$. The concrete ranging from $60{\sim}80MPa$, shows the biggest diminution of modulus of elasticity under $400^{\circ}C$, which implies the structural unstability of temperature.

• Earthquakes and Structures
• /
• 제26권2호
• /
• pp.97-115
• /
• 2024

In this paper, a database consisting of the dynamic shear modulus ratio and damping ratio test data of clay obtained from 406 groups of triaxial tests is constructed with the starting area of Xiong'an New Area as the research background. The aim is to study the nonlinear dynamic properties of clay in this area under cyclic loading. The study found that the effective confining pressure and plasticity index have certain influences on the dynamic shear modulus ratio and damping ratio of clay in this area. Through data analysis, it was found that there was a certain correlation between effective confining pressure and plasticity index and dynamic shear modulus ratio and damping ratio, with fitting degree values greater than 0.1263 for both. However, other physical indices such as the void ratio, natural density, water content and specific gravity have only a small effect on the dynamic shear modulus ratio and the damping ratio, with fitting degree values of less than 0.1 for all of them. This indicates that it is important to consider the influence of effective confining pressure and plasticity index when studying the nonlinear dynamic properties of clays in this area. Based on the above, prediction models for the dynamic shear modulus ratio and damping ratio in this area were constructed separately. The results showed that the model that considered the combined effect of effective confining pressure and plasticity index performed best. The predicted dynamic shear modulus ratio and damping ratio closely matched the actual curves, with approximately 88% of the data falling within ±1.3 times the measured dynamic shear modulus ratio and approximately 85.1% of the data falling within ±1.3 times the measured damping ratio. In contrast, the prediction models that considered only a single influence deviated from the actual values, particularly the model that considered only the plasticity index, which predicted the dynamic shear modulus ratio and the damping ratio within a small distribution range close to the average of the test values. When compared with existing prediction models, it was found that the predicted dynamic shear modulus ratio in this paper was slightly higher, which was due to the overall hardness of the clay in this area, leading to a slightly higher determination of the dynamic shear modulus ratio by the prediction model. Finally, for the dynamic shear modulus ratio and damping ratio of the engineering site in the starting area of Xiong'an New Area, we confirm that the prediction formulas established in this paper have high reliability and provide the applicable range of the prediction model.