• 한국해양공학회지
• /
• 제20권1호
• /
• pp.26-31
• /
• 2006

Experimental research was undertaken to develop a domestic spray nozzle used on equipment for desalination. First, we made a test set-up in order to confirm nozzle efficiency of spray and distribution under different pressure conditions. Then, we found a maximum spray condition after verifying reliability of this facility. An optimum arrangement of the nozzle, based on the test result, was made using CATIA V5 and EXCEL.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.56-62
• /
• 1999

The disintegration of transient diesel spray in early was investigated at different opening pressure and chamber pressure by measns of shadowgraph method using nanolite and still camera. Diesel spary was injected into the spray chamber which was charged with high pressure nitrogen gas. Atthe begining of injection, a liquid column that was almost the same diameter as the nozzle hole was observed . Spray tip penetration and spray angle were always increased with an increase in opening pressure.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권4호
• /
• pp.912-919
• /
• 2001

Improvement of the atomization characteristics by adopting the air-shrouded injector has been considered as one of the important methods for decreasing HC emissions in SI engines. Thus, in this study to develop air-shrouded injector with a finer spray, atomization characteristics of differ-ent types of commercial air-shrouded injectors were investigated through the spray imaging and the drop size measurements. As a results, it was found that the internal mixing type of air-shroud-ed injector had a good atomization characteristics. But, a number of large droplets were found in the internal mixing type commercial injector, this shortcoming was improved by adopting the thread type air passages in the air nozzle.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.164-170
• /
• 1992

In order to understand and explain the spary combustion, it was necessary to understand the disintegration mechanisms of liquid jet. To understand the disintegration mechanisms of liquid jet, the disintegration phenomena and uniform droplet production regions of testing liquid jet was investigated by means of longitudinally vibration capillary nozzle, which was injected the testing liquids. The testing liquids were light oil and light oil and light oil blended with 25wt% fish oil (File fish oil, Sardine fish oil, Alaska pollac oil) The results can be summarized as follows: 1. The uniform droplet phenomena have been changed according to the frequency of capillary tube, the jet velocity and physical properties of testing oils. 2. Within the region of uniform droplet, Reynold number was increased as Weber number increases. 3. The lower limit of wave length in which uniform droplet was produced 0.8d which was lower than Rayleigh wave length 4. The light oil blended with file fish oil which has lower viscosity and surface tension had the widest uniform droplet production region on the frequency and velocity among testing oils. But light oil blended with sardine fish oil were similar with light oil in the uniform production region.

• 생물환경조절학회지
• /
• 제7권4호
• /
• pp.298-310
• /
• 1998

본 연구에서는 온실냉방용 포그시스템 설계시 필요한 기초자료 확보를 위하여 경상대학교내 실험온실에 설치한 3종류의 노즐을 중심으로 분무특성에 대해 실험을 수행하였다. 그 결과 단위 노즐당 분무량은 분무압력이 증가할수록 증가하나, 각 노즐에서 공히 분무압력의 증가에 따른 분무량의 증가율이 일정하지 않았다. 노즐의 유형 I, II, III형별로 전체 실험분무압력에서 최소입경은 각각 약 1.7~2.5$\mu$m, 1.7~2.2$\mu$m 및 1.7~2.2$\mu$m이었고, 최대입경은 각각 약 44~60$\mu$m, 52~71$\mu$m 및 45~61$\mu$m이었으며, 평균입경은 각각 약 23~38$\mu$m, 19~24$\mu$m 및 17~25$\mu$m범위에 있었다. 그리고 노즐 I, II, III 별로 분무입경이 가장 양호하다고 판단된 분무압력은 각각 70kg/$\textrm{cm}^2$, 30kg/$\textrm{cm}^2$ 및 30kg/$\textrm{cm}^2$이었으며, 그 때의 분무량은 각각 124mL/min, 103mL/min 및 84mL/min정도였고, 평균입경은 각각 약 22.6$\mu$m, 21.8$\mu$m 및 20.6$\mu$m정도였다. 또한 전체 입경분포에서 30$\mu$m이하가 차지하는 비율은 노즐(I, II 및 III)별로 각각 95.4%, 85.7%, 79.0%정도였으며, 비교적 입자가 큰 40$\mu$m이상이 차지하는 비율은 각각 0.2%, 1.28% 및 1.67%정도였다. 그러나 이들 노즐들의 분무입자 크기는 대부분 포그의 한계입경인 50$\mu$m이하에 속하였다.