• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.65-75
• /
• 2001

Modern vehicles require a high degree of refinement including good driveability. Vehicle driveability, which becomes a key decisive factor f3r marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. Therefore engine and drive train characteristics should be considered to achieve a well balanced vehicle response simultaneously. This paper describes experimental procedures which have been developed to measure engine torque and investigate shuffle characteristics. To analyze the vehicle dynamic behavior, fractional torques and inertia mass moment of engine, and drive train were measured. Shuffle characteristics during tip-in condition were investigated in an experimental vehicle at 2nd and 3rd gear stages. It was found that the shuffle characteristics were caused by sudden changes of engine torque and have a different vibration frequency with gear stage variation. Inertia mass moment of engine including flywheel rotation showed a key factor for the shuffle characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.85-91
• /
• 2001

LPG has been well known as a clean alternative fuel for vehicles. As a fundamental study on liquid phase LPG injection (hereafter LPLI) system application to heavy-duty engine, engine output and combustion performance were investigated with various operating conditions using a single cylinder engine equipped with the LPLI system. Experimental results revealed that no problems were occurred in application of the LPG fuel to heavy-duty engine, and that volumetric efficiency and engine output, by 10% approximately, were increased with the LPLI system. It was resulted from the decrease of the intake manifold temperature through liquid phase LPG fuel injection. These results provided an advantage in the decrease of the exhaust gas temperature, in the control of knocking phenomena, spark timing and compression ratio. The LPLI engine could normally operated under $\lambda$=1.5 or EGR 30% condition. The optimized swirl ratio for the heavy duty LPG engine was found around R_s$ = 2.0.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.75-84
• /
• 1988

The performance and emission for the 4-cylinder 4-cycle gasoline engine fueled with methanol is predicted in this paper. The model for all the processes is illustrated. It computes the gas pressure, gas temperature and the rate of formation of nitric oxide and carbon monoxide at each crank angle using basic energy equation and reaction kinetic mechanism. The results are obtained at different operating conditions encompassing changes in fuel-air equivalence ratio, engine speed, spark timing and compression ratio. The special characteristics of methanol such as high power output and nitric oxide emissions have been truthfully predicted by the model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.178-185
• /
• 1998

To reduce the particulate matter and nitrogen oxides from diesel engine, many studies are proceeding and being accomplished practically. In this situation CNG engine has important meaning both as a clean fuel and an alternative energy. In order to present the direction and application of CNG, we simulated various operating conditions, that is, spark timing, compression ratio and fuel composition etc. Thus we try to understand how those affect performance and exhaust characteristics. The simulation program results found that the optimum combustion start angle was 21$^{\circ}$ at 1800rpm and fuel composition affects performance and emissions, also we could understand the formation of emission as crank angle is changed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.16-21
• /
• 2003

Natural gas is one of the promising alternative fuels because of the abundant deposits and the cleanness of emission gas. It can be used in conventional gasoline engine without major modification. Natural gas has some advantages than gasoline i.e. the high octane number, good mixing condition because of gas and wide inflamable limit. In the present study, a $1.8{\ell}$ conventional gasoline engine is modified for using the CNG as a fuel instead of gasoline. Performance and emission characteristics are compared between gasoline and CNG with 4 cylinder SI Engine which is controlled by programable ECU. Parameters of experimentation are equivalence ratio, spark timing and fuels. We analyzed the combustion characteristics of the engine using the cylinder pressure i.e. ignition delay, combustion duration and cycle variation. As a result, CNG engine shows lower exhaust emissions but brake torque is slightly reduced compared to gasoline engine. Overall combustion duration is longer than that of gasoline because of lower burning speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.89-95
• /
• 2003

We consider a problem of application of analytical redundancy to engine synchronization process of spark ignition engines, which is critical to timing for every ECU process including ignition and injection. The engine synchronization process we consider here is performed using the pulse signal obtained by the revolution of crankshaft trigger wheel (CTW) coupled to crank shaft. We propose a discrete-time linear model for the signal, for which we construct FDI (Fault Detection & Isolation) system consisting residual generator and threshold based on linear observer.

• Journal of ILASS-Korea
• /
• v.23 no.2
• /
• pp.96-101
• /
• 2018

The purpose of this study is to investigate the effect of water injection on combustion characteristics of gasoline direct injection (GDI) engine with turbo-charger under low-load operating condition. The test engine used in this study has four-cylinder and 10.2 of compression ratio. In order to study the effect of water injection ratio on combustion characteristics, the water was injected into the intake port from 10% to 50%, based on fuel injection quantity. From the experiment, it revealed that the water injection induced the improvement of fuel economy because of the advance of spark-timing by the reduction of in-cylinder temperature. In addition, the water injection caused the prolong of extension of the ignition delay and slight increase of burn duration.

• Journal of the Korean Society of Safety
• /
• v.10 no.3
• /
• pp.11-20
• /
• 1995

In recent years, the study on the high efficiency of the internal combustion engine has been mainly proceeding. In this study, we developed rotary valve to achieve the improvement of volumetric efficiency and to be simple construction. And then made a comparative analysis between rotary and poppet valve. In this experiment, rotary valve enlarged the flow area of valve port to minimize the resistance of the fluid flow and to flow smoothly in intake and exhaust process. Indeed, valve timing was controlled properly lest positive pressure in exhaust process should affect intake process. Motoring and firing experiments were using engine speed and air-fuel ratio as the principle parameter and the full opening of throttle valve and minimum spark advance for best torque (MBT) as engine operating variables.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.55-65
• /
• 1987

This paper presents the method of piston temperature measurement and its data under various engine operating conditions. In case of high speed engine, the thermocouple wires must be guided from moving piston to stationary place with carful attention. for this purpose L_LINK SYSTEM was made and assembled to a passenger car engine on the test bench and then the piston temperature was successfully measured. The tested engine speed ranged from 1,000 to 4,000 rpm with 500 rpm increments. Not only the effects of engine speed and load on the piston temperature but those of spark timing, detonation, coolant temperature and Reynolds number based on inlet air condition were studied form the measurement obtained by this L_LINK SYSTEM.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1196-1202
• /
• 2003

The concept of hydrogen enriched LPG fuelled engine can be essentially characterized as low emissions and reduction of backfire for hydrogen engine. The purpose of study is obtaining low-emission and high-efficiency in LPG engine with hydrogen enrichment. In order to determine the ideal compression ratio, a variable compression ratio single cylinder engine was developed. The objective of this paper is to clarify the effects of hydrogen enriched LPG fuelled engine on exhaust emission, thermal efficiency and performance. The compression ratio of 8 was selected to minimize abnormal combustion. To maintain equal heating value, the amount of LPG was decreased, and hydrogen was gradually added. In a similar manner, the relative air-fuel ratio was increased from 0.8 to 1.3 in increment of 0.1, and the ignition timing was controlled to be at MBT each case.