• 한국전자파학회논문지
• /
• 제24권5호
• /
• pp.541-548
• /
• 2013

본 논문에서는 상용 벡터 회로망 분석기를 사용하지 않고도, 신호 발생기, 벡터 전압 수신기, 방향성 결합기, 주파수 혼합기 등의 기본적인 초고주파 장비/소자를 활용하여 평가하고자 하는 초고주자 소자의 2-포트 산란 계수를 측정할 수 있는 시스템을 제안한다. 벡터 회로망 분석기를 대용할 수 있는 산란 계수 측정 시스템의 해석적 모델과 제작방법을 제시하고, 이를 1-포트와 2-포트 소자에 대하여 각각 적용한 산란 계수를 측정하여 구현된 시스템을 평가하였다. 평가 주파수 대역에 따라 비교적 낮은 대역에서는 단일 신호 발생기와 벡터 전압 수신기를 사용한 직접 수신법을, 높은 대역에서는 추가의 신호원과 주파수 혼합기를 사용하여 신호를 하향 복조하는 헤테로다인 방식을 사용하여 산란 계수를 결정짓는 벡터 전압을 수신하였다. 이들 각각의 수신 방법으로 UHF와 X 대역 초고주파 소자의 2-포트 산란 계수를 평가하였고, 그 유효성을 상용 벡터 회로망 분석기로 검증하였다.

• Journal of Power Electronics
• /
• 제14권2호
• /
• pp.271-281
• /
• 2014

Fluctuating wind conditions necessitate the use of a variable speed wind turbine (VSWT) with a AC/DC/AC converter scheme in order to harvest the maximum power from the wind and to decouple the synchronous generator voltage and frequency from the grid voltage and frequency. In this paper, a combination of a three phase diode bridge rectifier (DBR) and a modified topology of the diode clamped multilevel inverter (DCMLI) has been considered as an AC/DC/AC converter. A control strategy has been proposed for the DCMLI to achieve the objective of grid interface of a wind power system together with local load compensation. A novel fixed frequency current control method is proposed for the DCMLI based on the level shifted multi carrier PWM for achieving the required control objectives with equal and uniform switching frequency operation for better control and thermal management with the modified DCMLI. The condition of the controller gain is derived to ensure the operation of the DCMLI at the fixed frequency of the carrier. The converter current injected into the distribution grid is controlled in accordance with the wind power availability. In addition, load compensation is performed as an added facility in order to free the source currents being fed from the grid of harmonic distortion, unbalance and a low power factor even though the load may be unbalanced, non-linear and of a poor power factor. The results are validated using PSCAD/EMTDC simulation studies.

• 한국전기전자재료학회논문지
• /
• 제25권2호
• /
• pp.147-152
• /
• 2012

This paper dealt with the frequency component analysis of acoustic signals produced by corona and series-arc discharges as a diagnostic technique for closed-switchboards. Corona and series-arc discharge were simulated by a needle-plane electrode and an arc generator specified in UL1699, respectively. Acoustic signal was detected by a wideband acoustic sensor with a frequency bandwidth of 4 Hz~100 kHz (-3 dB). We analyzed frequency spectrums of the acoustic signals detected in various discharge conditions. The results showed that acoustic signals mainly exist in ranges from 30 kHz to 60 kHz. From the experimental results, an acoustic detection system which consists of a constant current power supply (CCP), a low noise amplifier (LNA) and a band pass filter was designed and fabricated. The CCP separates the signal component from the DC source of acoustic sensor, and the LNA has a gain of 40 dB in ranges of 280 Hz~320 kHz. The high and the low cut-off frequency are 30 kHz and 60 kHz, respectively. We could detect corona and series-arc discharges without any interference by the acoustic detection system, and the best frequency is considered in ranges of 30 kHz~60 kHz.

• 한국전산유체공학회지
• /
• 제9권3호
• /
• pp.49-56
• /
• 2004

A heated and expanded helium is used to pressurize liquid propellants in propellant tanks of propulsion system of liquid propellant launch vehicles. To produce a heated and expanded helium, an hot-gas heat exchanger is used by utilizing heat source from an exhausted gas, which was generated in a gas generator to operate turbine of turbo-pump and dumped out through an exhaust duct of engine. Both experimental and numerical approaches of hot-gas heat exchanger design were conducted in the present study. Experimentally, siliconites - electrical resistance types - were used to simulate the full heat condition instead of an exhausted gas. Cryogenic heat exchangers, which were immersed in a liquid nitrogen pool, were used to feed cryogenic gaseous helium in a hot-gas heat exchanger. Numerical simulation was made using commercially utilized solver - Fluent V.6.0 - to validate experimental results. Helically coiled stainless steel pipe and stainless steel exhausted duct were consisted of tetrahedron unstructured mesh. Helium was a working fluid Inside helical heat coil and regarded as an ideal gas. Realizable k-』 turbulent modeling was adopted to take turbulent mixing effects in consideration. Comparisons between experimental results and numerical solutions are Presented. It is observed that a resulted hot-gas heat exchanger design is reliable based on the comparison of both results.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.498-498
• /
• 2013

Atmospheric Pressure Plasmas have pioneered a new field of plasma for biomedical application bridging plasma physics and biology. Biological and medical applications of plasmas have attracted considerable attention due to promising applications in medicine such as electro-surgery, dentistry, skin care and sterilization of heat-sensitive medical instruments [1]. Traditional approaches using electronic devices have limits in heating, high voltage shock, and high current shock for patients. It is a great demand for plasma medical industrial acceptance that the plasma generation device should be compact, inexpensive, and safe for patients. Microwave-excited micro-plasma has the highest feasibility compared with other types of plasma sources since it has the advantages of low power, low voltage, safety from high-voltage shock, electromagnetic compatibility, and long lifetime due to the low energy of striking ions [2]. Recent experiment [2] shows three-log reduction within 180-s treatment of S. mutans with a low-power palm-size microwave power module for biomedical application. Experiments using microwave plasma are discussed. This low-power palm-size microwave power module board includes a power amplifier (PA) chip, a phase locked loop (PLL) chip, and an impedance matching network. As it has been a success, more compact-size module is needed for the portability of microwave devices and for the various medical applications of microwave plasma source. For the plasma generator, a 1.35-GHz coaxial transmission line resonator (CTLR) [3] is used. The way of reducing the size and enhancing the performances of the module is examined.

• 한국추진공학회지
• /
• 제13권5호
• /
• pp.1-6
• /
• 2009

로켓시스템의 에너지원으로 적용할 수 있는 기체발생기용 복합 고체추진제의 개발과정을 기술한다. 80%의 고체입자 부하율과 양호한 유동성, 그리고 $-50^{\circ}{\sim}70^{\circ}C$에서 경화에 적절한 추진제 물성을 갖는 HTPB를 바인더로 하여, 낮은 화염온도, 적은 고체입자 잔사, 무독성 생성물의 추진제 제조가 가능한 AN을 제1종 산화제로, 탄도특성 제어에 필요한 AP를 제2종 산화제로 추진제 주요 조성이 구성된다. 기본조성을 근거로 하여 일련의 물성개선 시험이 수행되었으며 최대응력 8 bar 및 최대응력점 변형율 30%, 그리고 탄성계수 1000 psi 수준의 물성을 갖는 추진제 조성을 얻을 수 있었다.

• 한국콘텐츠학회논문지
• /
• 제9권2호
• /
• pp.152-162
• /
• 2009

현재 위피 응용프로그램을 개발하기 위한 저작도구는 코드 작성의 편의성이 부족하고, 시각화를 배제한 문법 중심의 프로그래밍 도구가 대부분이다. 이로 인해 위피 응용프로그램 개발 시 개발자가 전체 개발과정에 걸쳐서 직접 코딩하여 개발하고 있다. 본 논문에서는 위피 응용프로그램을 신속하고 용이하게 개발 할 수 있는 절차로써 위피API의 상위레벨(High level) 컴포넌트를 그래픽 컨트롤로 시각화하고, 이를 이용하여 시스템에서 제공한 모바일 레이아웃에 개발자가 쉽게 디자인한 후, UI 명세 언어와 소스 코드로 생성 해주는 과정을 거치는 개발 방안을 제시한다. 이를 위하여 위피 Jlet의 UI 명세 언어인 JIML(Jlet Interface Markup Language)을 제안하고, 제안한 JIML로부터 위피 Jlet의 UI와 관련된 위피 코드로의 생성을 위한 변환 규칙을 제시한다. 또한 위의 개발 과정을 자동으로 처리하는 시스템을 구현하였다. 구현한 시스템은 위피 비즈니스 프로그램 개발 시 효율성을 제공하고, 빠른 개발이 가능하도록 도와준다.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2001년도 정기총회 특별강연 및 춘계학술연구발표회(2)
• /
• pp.85-91
• /
• 2001

This paper provides a case study of landfill gas (LFG) utilization fer direct use as process fuel, and for electrical power generation at restored landfills in the Hong Kong Special Administrative Region of China (HKSAR). The paper specifically covers the LFG utilization schemes, which are required under landfill restoration contracts at the Shuen Wan and Urban Landfills. These contracts provide for the restoration and aftercare of six landfills, and are administered by the Environmental Protection Department (EPD) of the Hong Kong Government. The LFG utilization scheme at the Shuen Wan Landfill incorporates the direct use of LFG by compressing and dehumidifying the LFG prior to conveyance through a 1.6-kilometer (1-mile) pipeline. The pipeline provides an alternate fuel source to naphtha during process heating for gas production at the Tai Po Gas Production Plant of the Hong Kong and China Gas Limited (HKCC). The LFG utilization scheme at the Jordan Valley Landfill (one of the Urban Landfills) beneficially uses the LFG as fuel for electrical power generation with reciprocating internal combustion engines. The LFG is compressed, cooled, and filtered prior to delivery to two engine/generator sets. This system provides power to operate the leachate pre-treatment plant, which processes leachate from all of the Urban Landfill sites. The case study will examine the technical and non-technical considerations, including harriers, for developing, designing and implementing the LFG utilization projects in Hong Kong. Specific regulatory considerations and external governmental agency approvals are discussed, including the requirement to register as a gas-producing utility. While the paper focuses on LFG utilization applications in Hong Kong, many of the considerations discussed are also applicable to development of LFG utilization in other regions of Asia.

• 대한기계학회논문집A
• /
• 제35권5호
• /
• pp.479-485
• /
• 2011

열 전자 방출 형 전자 빔 장치에서 영상을 획득하기 위해서는 텅스텐 필라멘트에서 발생한 전자빔을 스캔 할 장치가 필요하다. 이때, 스캔 되는 주파수에 따라서 시료 표면에서 튀어 나오는 2 차 전자신호에 대하여 잡음 성분의 발생이 다르게 나타난다. 본 연구에서는 잡음 성분 제거를 위한 필터 설계를 위해서 2 차 전자신호에 대한 실시간 주파수 분석을 통해 신호와 잡음 성분을 구분했다. 그리고 부동 소수점 연산이 가능한 DSP 에서 디지털 필터 설계를 통하여 신호대비 잡음 성분 제거를 통하여 고배율로 획득한 전자현미경의 영상의 질을 향상 시켰다.

• 대한조선학회논문집
• /
• 제50권3호
• /
• pp.190-198
• /
• 2013

In order to predict acoustic pressure distributions by exterior incident wave at Cylindrical Hydrophone Array (CHA) sensor's positions, acoustic pressure analysis is performed by using beam tracing method. Beam tracing method is well-known of reliable pressure analysis methods at high-frequency range. When an acoustic noise source is located at the center of rectangular room, acoustic pressure analysis is performed by using both beam tracing method and Power Flow Boundary Element Method (PFBEM). By comparing with results of beam tracing method and those of PFBEM, the accuracy of beam tracing method is verified. We develop the CHA pressure analysis program by verified beam tracing method. The developed software is composed of model input, sensor array creator, analysis option, solver and post-processor. We can choose a model option of 2D or 3D. The sensor array generator is connected to a sonar which is composed of center position, bottom, top and angle between sensors. We also can choose an analysis option such as analysis frequency, beam number, reflect number, etc. The solver module calculates the ray paths, acoustic pressure and result of generating beams. We apply the program to 2D and 3D CHA models, and their results are reliable.