• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1482-1489
• /
• 2007

In this paper, characteristics of infrasound and low-frequency noise emission from large modern wind turbines are experimentally investigated. The sound measurement procedures of IEC 61400-11 and ISO 7196 are utilized to field test and evaluation of noise emission from each of 1.5 MW and 660 kW wind turbines using the stall regulation and the pitch control for the power regulation, respectively. It was found that the G-weighted SPLs of low-frequency noise including infrasound shows positive correlation with the wind speeds, irrespective of methods of power regulation. This highlights the potential complaint of local community against the infrasound and low-frequency noise of wind turbines. The comparison of measured data with the existing hearing thresholds and criteria curves shows that it is highly probable that the low-frequency noise from the 1.5 MW and 660 kW wind turbines in the frequency range over 30 Hz leads to the psychological complaint of ordinary adults, and that the infrasound in the frequency range from 5 Hz to 8 Hz causes the complaint by rattling the house fitting such as doors and windows.

• 한국철도학회논문집
• /
• 제15권6호
• /
• pp.531-536
• /
• 2012

판토그라프 팬헤드의 공력소음 발생의 주요 인자와 영향을 미치는 변수를 분석하였다. 팬헤드 주변의 유체 유동과 결과적인 소음 방사를 분석하기 위해, 수치해석적인 방법 중 하나인 격자볼츠만 방법으로 팬헤드 단순모델을 사용했다. 풍동실험을 통해 측정된 결과로 시뮬레이션 결과를 검증했다. 와흘림이 주요한 공력소음 발생원인이며 Strouhal수, 유체의 속도 및 판토그라프의 형상에 영향을 받았다. 이 논문에 사용된 직사각형 형상을 통해 양력의 발생을 증가시키면서 방사 소음을 줄이는 팬헤드의 설계가 가능함을 제시하였다. 또한 통로나 유선 형상을 이용해 와흘림을 최소로 줄이면, 방사 소음을 크게 저감하는 형상의 설계가 가능함을 구축된 해석모델을 이용하여 검증하였다.

• 동력기계공학회지
• /
• 제3권3호
• /
• pp.60-69
• /
• 1999

The noise and vibration sources of rotary compressor for room air-conditioner are pressure pulsation of compression process, cavity resonance of inner space, structural radiation noise of shell and impact noise of discharge valve. Among them, pressure pulsation is very important noise and vibration source. Because it transferred various kinds of noise and vibration like as mentioned above. In this reason, muffler and resonator are used in order to absorb and remove these noises. But an analytical prediction using acoustic analysis does not coincident with the experimental result. The difference between analysis and actual state is due to the assumption of analysis. This paper covered with new concept of muffler design based on the turbulence kinetic energy of flow by using CFD. From this analysis, it is possible to decide the best position of discharge port of muffler. Therefore $2{\sim}3dB$ noise reduction effect is acquired in rotary compressor of 5000 BTU grade. Also new approach of resonator design is suggested. From this study, the characteristics of resonator and surge hole (a kind of resonator without pipe length) are identified. The former is useful for pure tone noise (narrow frequency band), and the latter is effective for broad frequency band. This paper shows that it is very available to use 3 dimensional analysis of resonator in order to predict more exact tuning frequency. The result is proved by a lot of experiments. From combination of fluid analysis and acoustic analysis, up stream position is effective location of resonator concerning turbulence motion of fluid.