• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.439-443
• /
• 2004

In this research, we describe the sorting conditions modeling by friction force. As in any mechanism which is required to provide good dynamic performance and high accuracy, performance evaluation of optimal control. To understand friction it is necessary to investigate the topography of the sliding surfaces in contact. Any surfaces, even apparently smooth surfaces, are microscopically rough. When two surfaces come into contact, the true contact takes place only at point where asperities come together. The sorting conditions of sorting mechanism with friction force is sorting force must be equal with force can sorting one highest veneer among loaded veneer. This is just a thing being sorted veneer have friction with under veneer and this friction disturb sorting at the same time. Hence, the sorting conditions evaluation is important to sorting one veneer must get under control friction with veneer.

• Resources Recycling
• /
• v.30 no.4
• /
• pp.3-10
• /
• 2021

The field of recycling for waste electronic components, which is the typical example of an urban mine, requires the development of useful sorting techniques. In this study, a sorter based on image identification by deep learning was developed to select electronic components into four groups. They were recovered from waste printed circuit boards and should be separated to depend on the difference after treatment. The sorter consists of a workstation with GPU, camera, belt conveyor, air compressor. A small piece (less than 3.5 cm) of electronic components on the belt conveyor (belt speed: 6 cm/s) was taken and learned as teaching data. The accuracy of the image identification was 96% as kinds and 99% as groups. The optimum condition of sorting was determined by evaluating accuracies of image identification and recovery rates by blowdown when changing the operating condition such as belt speed and blowdown time of compressed air. Under the optimum condition, the accuracy of image classification in groups was 98.7%. The sorting rate was more than 70%.

• Journal of Korea Water Resources Association
• /
• v.49 no.1
• /
• pp.73-81
• /
• 2016

This study investigates the development of lower channels and sediment sorting processes in the vegetated channels with the mixed sediment. The sediment discharges fluctuate with time and decrease with vegetation density. The bed changes with irregular patterns, and the sediment particles in the vegetated zone at the surface of bed are fine. The dimensionless geometric mean decreases with vegetation density. The fine sediment particles are trapped by vegetation, and the bed between main steam and vegetated zone increases. Moreover, the particle sizes are distributed irregularly near the zone. The hiding functions decrease with dimensionless particle size. However, the functions increase with vegetation density, which is confirmed by decreasing sediment discharge with vegetation. The lower channel is stable and the migration decreases in the condition of $0.5tems/cm^2$. However, the migration of the lower channel in the condition of $0.7stems/cm^2$ increases due to the increased sinuosity and new generated channels in the sedimentated vegetation zone.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.211-216
• /
• 2015

Recently, because of the growth in the leisure industry and interest in health, the demand for bicycles has increased. In this research, considering the vertical load on a bike frame under static state conditions, the deflection and mass of the bike frame were minimized by satisfying the service condition and performing optimization. The thickness of the bicycle-frame tube was set to a design variable, and its sensitivity was confirmed by an analysis of means (ANOM). To optimize the solution, a response-surface-method (RSM) model was constructed using D-Optimal and central composite design(CCD). The optimization was performed using a non-dominant sorting genetic algorithm (NSGA-II), and the optimal solution was verified by finite-element analysis.

• The Journal of Fisheries Business Administration
• /
• v.45 no.2
• /
• pp.85-95
• /
• 2014

Fish stocking is important element of land-based aquaculture management. To maintain constant stocking rate considering biological and economic condition is a convenient strategy in intensive aquaculture. This study is aimed to analyze the effect of over-stocking(more than aquaculture capacity) for certain periods of time. This study make the mathematical decision making model that finds the value of decision variable to minimize cost that sums up the water pool usage cost and sorting cost under critical standing corp constraint. The proposed mathematical decision making model was applied to 12 sample combination of sorting cost and the number of fish on the Oliver flounder culture farms. If a immature fish can be sold for high price than farming cost, restricted over-stocking resulted in a improvement of economic performance. When extensive comparable biological and market data become available, analysis model can be widely applied to yield more accurate results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.4
• /
• pp.434-439
• /
• 2008

The amount of salt to make seed sorting solution of the specific gravity of 1.13 was reconsidered and determined as 3.8 kg salt in 18 L water, which is lower amount than currently used. Five rice cultivars were examined. Percent germination and seedling emergence were not similar. Seedling emergence rate of Japonica varieties, Nampyungbyeo and Daerypbyeo-1 were 87% and 95% under specific gravity of 1.13, respectively. Seedling emergence rate of Tongil type variety, Dasanbyeo was as high as 67% in specific gravity of 1.06. Seedling emergence rate of waxy rice, Hwasunchalbyeo and Aranghangchalbyeo were examined. Seedling emergence rate was 94% in both cultivars in specific gravity of 1.04. Seedling emergence rate was same in specific gravity of 1.08 which is generally used for selecting seed currently. Early growth (plant height, leaf number, and dry weight) were not significantly different by specific gravity within species. In all cultivars except waxy rice, highest seedling emergence rate was observed in specific gravity of 1.13 which is currently used for selection and decreased as specific gravity is lowed. However, considering total amount of seeds in each group of specific gravity, amount of seed in lower specific gravity group is relatively small and total seedling emergence rate within variety dose not show big difference. However, if seeds with low speicific gravity are produced due to the bad grain filling condition and consequently total seed content of low specific gravity increases, results will be differnt. Reduction in total growth and yield could occur. It will be important to comply with the seed sorting criterion of 1.13 for Japonica, 1.06 for Tongil, and 1.04 for waxy rice variety to ensure the maximum rice growth and yield.

• Korean Journal of Organic Agriculture
• /
• v.16 no.3
• /
• pp.239-258
• /
• 2008

This study identifies the spectrum of different forms of sharing labor in farm houses following the increase in the production of organic produce and deals with the gender division of labor and every day life of the farm households. The increased labor burdens of organic farming give more work opportunities to wives, weakening the gender barriers. However, some of the farm households seeking for economic feasibility are strengthening the gender barriers by specialized work divisions, leading to outside order labor of harvest, sorting, and packaging in order to increase efficiency in agricultural management in extreme cases. Even in the alternative distribution system, farm households has become subject to the distribution system as it is shown that coop claimed the segmentation of sorting work. This is because the convenience of the customers goes before the advantages of producers. Jinju, seeking for economic feasibility, has established the springboard for growth by greenhouse through monoculture and specialization and are operating economic growth stably. Farm couples with this condition, where their incomes are relatively high, are attempting to recharge their energy during low seasons. It is expected that this will be a model case of conventionalization of organic farming. Significance of organic farming in this matter is discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.702-707
• /
• 2007

A Color Discerning Device(CDD) is the equipment to use in a Rice Processing Complex(RPC). A CDD can sorting discolored grain according to light and shade. The existing a CDD's driving performance is not so good as overseas machine. Besides, transportation process causes a defect in the mechanism from impact or harmonic excitation or etc. This study is represented the problem of CDD through experiment and simulation on a CDD. To analysis the problem of driving condition, devide each part of CDD for performed modal analysis. The problem of driving of driving condition and transportation process solved by carry out modal analysis and static analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.571-576
• /
• 2006

A Color Discerning Device(CDD) is the equipment to use in Rice Processing Complex(RPC). By use a high-speed charge-coupled device camera, CDD can sorting discolored grain according to light and shade. The existing CDD's driving performance is not so good as overseas machine. Besides, transportation process causes a defect in the mechanism from impact or harmonic excitation or etc. This study is represented the problem of CDD through modal analysis and static analysis by using ANSYS workbench. To analysis the problem of driving condition, devide each part of CDD for performed modal analysis. The problem of driving condition and transportation process solved by carry out modal analysis and static analysis.

• Journal of the Korean Ceramic Society
• /
• v.51 no.2
• /
• pp.132-137
• /
• 2014

The study was performed with low-grade limestone, which is used to make cement or is disposed of due to its low CaO content. In this study, the optimal condition of limestone with which to manufacture precipitated calcium carbonate (PCC) and limestone in fiber was determined through in-situ reactions. The best firing condition is with slaked lime with rapid cooling after 2 h of firing at $1000^{\circ}C$. In addition, the content of CaO can be increased by sorting the low-grade limestone using a 200 mesh filter, and the optical quality of old newspaper (ONP) was similar when using both low-grade and high-grade limestone. Also, controlling the particle size of PCC is an important factor pertaining to the optical characteristics of paper.