• Resources Recycling
• /
• v.27 no.5
• /
• pp.38-48
• /
• 2018

Deep cement mixing method (DCM) is used to improve the quality of various ground type and its technical development proceeding based on performance improvements of solidification materials and mixing techniques with ground soil. In this study, it was possible to improve silty clay ground soil had 1 to 3 MPa compressive strength using solidification material that composed mainly circulating fluidized bed combustion (CFBC) power plant fly ash and reduce standard deviation of strengths from over 1.0 MPa to 0.322 MPa using improved auger bits in field test to forming more uniform bulbs than in case of using existing auger bit.

• Journal of Welding and Joining
• /
• v.20 no.2
• /
• pp.82-89
• /
• 2002

In order to clarify hot cracking phenomena occurred in Inconel 690 welds and it's prevention, in this study, the cracking behavior and the influence of welding variables on cracking in Inconel 690 overlay welds on Mn-Ni-Cr-Mo steel(SA 508 cl.3) for pressure vessel were investigated by using mock-up test. The main results are as follows: The cracks in Inconel 690 overlay welds were mainly generated near the start and the end part of welding beads adjacent to STS 309L welded outside of Inconel 690 welds. Most of the cracks showed typical solidification crack, and also it was assumed that there was possibility of liquation cracking in HAZ. The existence of Nb constituents or concentration of Nb was recognized on the fracture facets of the solidification cracks in the welds by SMAW. Therefore Nb was considered to be the main factor of the solidification cracking. As the weld heat input was more increased and the weld bead length was longer, the extent of cracking was more increased. Moreover the extent of cracking was considerably decreased by changing of welding sequence to the start and the end part of welds. Hot cracking in welds by GTAW was considerably decreased as compared with that of SMAW. And cracks were well generated in the Inconel 690 overlay welds adjacent to 575 309L welds. This means that the hot cracking susceptibility of Inconel 690 welds was largely varied by chemical components and/or compositions of filter metals, base metals and neighboring welds.

• Journal of Korean Society on Water Environment
• /
• v.25 no.3
• /
• pp.404-410
• /
• 2009

In this study, research for physical and chemical characteristics were conducted through analysis of sediments, grading and heavy metals (e.g., Mn, Cu, Cd, Zn and Pb ) in sewers which are classified by drainage types. After that, cement solidification and yellow soil calcinations made heavy metals stabilized and then, ways of recycling it were examined. The grain size distribution of all sediments was relative graded. When evaluating heavy metal pollution through index of geoaccumulation (Igeo), Cu showed moderately pollution or strong pollution in forest and street site and Zn was assessed by moderately pollution in military, residential, and street site. Analysis of Pearson Correlation coefficient of heavy metal indicated that all items in street site have tight relationship respectively. Especially, Cd-Zn, Cu-Pb, Cu-Mn, and Pb-Mn have relationship at 99% confidence intervals in statistical analysis. Recycling it with cement solidification was satisfied with compressive strength standard under 55% deposit contents and Zn, Pb, Mn were stabilized effectively. If time and temperature plasticity and compressive strength would be standard, it is revealed that yellow soil calcinations is valuable aggregate when it has 50-60 Wt% contents. When considering economic feasibility and stabilization of heavy metals, cement solidification would be more appropriate than yellow soil calcinations as solution to recycling.

• Journal of Korea Foundry Society
• /
• v.25 no.5
• /
• pp.195-202
• /
• 2005

In this study, we investigated the effect of Sb/RE on the microstructure and mechanical properties of as-cast heavy sectioned, over 250mm thickness, ferritic ductile cast iron. Exothermic and thermal insulation material were equipped on the wall of sand cast mold having the dimensions of $250{\times}250{\times}250$ mm. The nominal composition of the molten metal was controlled to be on the eutectic composition and Sb was added about 0, 0.005 and 0.02% respectively. In the center of as-cast ingot without Sb addition, the solidification of chunky graphite was induced by the eutectic reaction that took long time, which caused the decrease of elongation and impact energy. In case that the value of Sb/RE is 0.8, the solidification of chunky graphite could be suppressed and the improvement of nodularity was observed. On the other hand, the excessive addition of Sb suppressed the solidification of chunky graphite but gave rise to the solidification of flake graphite and the increase of pearlite contents. This results in poor elongation and impact energy which is lower than those in the case of no Sb addition.

• Journal of Welding and Joining
• /
• v.25 no.5
• /
• pp.45-50
• /
• 2007

The Ni-base superalloy GTD111 DS is used in the first stage blade of high power land-based gas turbines. Advanced repair technologies of the blade have been introduced to the gas turbine industry over recent years. The effect of the filler metal powder on Transient Liquid Phase bonding phenomenon and tensile mechanical properties was investigated on the GTD111 DS superalloy. At the filler metal powder N series, the base metal powders fully melted at the initial time and a large amount of the base metal near the bonded interlayer was dissolved by liquid inter metal. Liquid filler metal powder was eliminated by isothermal solidification which was controlled by the diffusion of B into the base metal. The solids in the bonded interlayer grew from the base metal near the bonded interlayer inward the insert metal during the isothermal solidification. The bond strength of N series filler metal powder was over 1000 MPa. and ${\gamma}'$ phase size of N series TLP bonded region was similar with base metal by influence of Ti, Al elements. At the insert metal powder M series, the Si element fluidity of the filler metal was good but microstructure irregularity on bonded region because of excessive Si element. Nuclear of solids formed not only from the base metal near the bonded interlayer but also from the remained filler metal powder in the bonded interlayer. When the isothermal solidification was finished, the content of the elements in the boned interlayer was approximately equal to that of the base metal. But boride and silicide formed in the base metal near the bonded interlayer. And these boride decreased with the increasing of holding time. The bond strength of M series filler metal powder was about 400 MPa.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.4
• /
• pp.303-310
• /
• 2000

This study is conducted in order to find more improved solidifying effects than the former converter slag solidification technology. The converter slag is used as a solidifying agent, and the quick lime and the gypsum are used as solidifying aids. Several tests are performed for the purpose of investigating the solidifying effects and the applicability of the solidified sludge as a daily or intermediate landfill cover. The unconfined uniaxial compressive strength, pH and leaching of heavy metal are investigated. In the case of using both quick lime and gypsum as solidifying aids, the compressive strength of specimen has significantly increased that of specimen which used quick lime only. The compressive strength of each specimen cured for 7 days which is mixed with quick lime and gypsum as mixing ratios 7:1, 5:1 and 3:1 are $0.59kg/cm^2$, $1.18kg/cm^2$, and $1.25kg/cm^2$, respectively. The results of all the leaching tests of specimen cured for 7 days show that the concentrations of leachate heavy metals(Cu, Pb, Cd and $Cr^{6+}$) are lower than the Korea toxic waste criteria. The microstructure analysis by SEM shows that needlelike crystals appear as the solidification proceed. The analysis of these crystals by EDS confirms that these main components are Ca. Si etc. Also, XRD analysis shows that the main solidification products are CSH and Ettringite; in addition, $Ca(OH)_2$ CAH are observed. When the added gypsum is used as a solidifying aid, more improved solidifying effects are obtained and the solidified sludge may be appropriately used as a daily or intermediate landfill cover.

• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.465-471
• /
• 1997

An integrated computer program consisting of a pre-processor, main solver, and post-processor was developed for the design of large steel castings. The pre-processor, based on the AutoCAD, enables the user to produce approval drawings, casting design drawings and mesh diagrams in sequence using a personal computer. In the main solver, two numerical models were employed; one models the fluid flow during mold filling, and the other models the heat transfer and solidification. The post-processor can be used to present simulation results such as flow pattern, mold filling sequences, solidification times, temperature gradients and location of shrinkage defects by color graphics. In order to validate the applicability of the present integrated program, a series of experiments on simple-shaped steel castings were carried out. After the validation of the present model, it was applied to the casting design of the large steel anchor of an SC42 alloy. Various solidification parameters such as a temperature distribution and a solidification time in the casting and the mold were compared with those obtained experimentally. Simulated results predicting shrinkage defects were in good agreement with those obtained experimentally. It was found that the present method can be successfully applied to the quantitative casting design for complex-shaped large steel castings.

• Journal of Korea Foundry Society
• /
• v.37 no.5
• /
• pp.148-156
• /
• 2017

The effects of minor additives on the casting properties of AC4A aluminum alloys were investigated. Measurements of the cooling curve and microstructure observations were conducted to analyze the effects of Ti-B and Sr minor elements during the solidification process. A fine grain size and an increase in the crystallization temperature for the ${\alpha}-Al$ solution were evident after the addition of 0.1wt% Al-5%Ti-1%B additive. The modification effect of the eutectic $Mg_2Si$ phase with the addition of 0.05% Al-10%Sr additive was prominent. A fine eutectic $Mg_2Si$ phase and a decrease in the growth temperature of the eutectic $Mg_2Si$ phase were evident. Fluidity, shrinkage and solidification-cracking tests were conducted to evaluate the castability of the alloy. The combined addition of Al-5%Ti-1%B and Al-10%Sr additives showed the maximum filling length owing to the effect of the fine ${\alpha}-Al$ grains. The macro-shrinkage ratio increased, while the micro-shrinkage ratio decreased with the combined addition of Al-5%Ti-1%B and Al-10%Sr additives. The macro-shrinkage ratio was nearly identical, while the micro-shrinkage ratio increased with the addition of the Al-10%Sr additive. The tendency of the occurrence of solidification cracking decreased owing to the effect of the fine ${\alpha}-Al$ grains and the modification of the $Mg_2Si$ phase with the combined addition of Al-5%Ti-1%B and Al-10%Sr additives.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.42 no.1
• /
• pp.1-7
• /
• 2019

In the modern industrial period, the introduction of mass production was most important progress in civilization. Die-casting process is one of main methods for mass production in the modern industry. The aluminum die-casting in the mold filling process is very complicated where flow momentum is the high velocity of the liquid metal. Actually, it is almost impossible in complex parts exactly to figure the mold filling performance out with the experimental knowledge. The aluminum die-castings are important processes in the automotive industry to produce the lightweight automobile bodies. Due to this condition, the simulation is going to be more critical role in the design procedure. Simulation can give the best solution of a casting system and also enhance the casting quality. The cost and time savings of the casting layout design are the most advantage of Computer Aided Engineering (CAE). Generally, the relations of casting conditions such as injection system, gate system, and cooling system should be considered when designing the casting layout. Due to the various relative matters of the above conditions, product defects such as defect extent and location are significantly difference. In this research by using the simulation software (AnyCasting), CAE simulation was conducted with three layout designs to find out the best alternative for the casting layout design of an automotive Oil Pan_BJ3E. In order to apply the simulation results into the production die-casting mold, they were analyzed and compared carefully. Internal porosities which are caused by air entrapments during the filling process were predicted and also the results of three models were compared with the modifications of the gate system and overflows. Internal porosities which are occurred during the solidification process are predicted with the solidification analysis. And also the results of the modified gate system are compared.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1376-1385
• /
• 2018

Ultrasonic melt treatment (UST) was applied to an A390 hypereutectic Al-Si alloy in a temperature range of $750-800^{\circ}C$ and its influence on the solidification structure and the consequent increase in strength was investigated. UST at such a high temperature, which is about $100^{\circ}C$ above the liquidus temperature, had little effect on the grain refinement but enhanced the homogeneity of the microstructure with the uniform distribution of constituent phases (e.g. primary Si, ${\alpha}-Al$ and intermetallics) significantly refined. With the microstructural homogeneity, quantitative analysis confirmed that UST was found to suppress the formation of Cu-bearing phases, i.e., $Q-Al_5Cu_2Mg_8Si_6$, $Al_2Cu$ phases that form in the final stage of solidification while notably increasing the average Cu contents in the matrix from 1.29 to 2.06 wt%. A tensile test exhibits an increase in the yield strength of the as-cast alloy from 185 to 208 MPa, which is mainly associated with the solute increment within the matrix. The important role of UST in the microstructure evolution during solidification is discussed and the mechanism covering the microstructure-strengthening interrelationship of the ultrasonically treated A390 alloy is proposed.