• 한국재료학회지
• /
• 제20권12호
• /
• pp.676-680
• /
• 2010

Most TCOs such as ITO, AZO(Al-doped ZnO), FTO(F-doped $SnO_2$) etc., which have been widely used in LCD, touch panel, solar cell, and organic LEDs etc. as transparent electrode material reveal n-type conductivity. But in order to realize transparent circuit, transparent p-n junction, and introduction of transparent p-type materials are prerequisite. Additional prerequisite condition is optical transparency in visible spectral region. Oxide based materials usually have a wide optical bandgap more than ~3.0 eV. In this study, single-phase transparent semiconductor of $SrCu_2O_2$, which shows p-type conductivity, have been synthesized by 2-step solid state reaction at $950^{\circ}C$ under $N_2$ atmosphere, and single-phase $SrCu_2O_2$ thin films of p-type TCOs have been deposited by RF magnetron sputtering on alkali-free glass substrate from single-phase target at $500^{\circ}C$, 1% $H_2$/(Ar + $H_2$) atmosphere. 3% $H_2$/(Ar + $H_2$) resulted in formation of second phases. Hall measurements confirmed the p-type nature of the fabricated $SrCu_2O_2$ thin films. The electrical conductivity, mobility of carrier and carrier density $5.27{\times}10^{-2}S/cm$, $2.2cm^2$/Vs, $1.53{\times}10^{17}/cm^3$ a room temperature, respectively. Transmittance and optical band-gap of the $SrCu_2O_2$ thin films revealed 62% at 550 nm and 3.28 eV. The electrical and optical properties of the obtained $SrCu_2O_2$ thin films deposited by RF magnetron sputtering were compared with those deposited by PLD and e-beam.

• 한국재료학회지
• /
• 제8권9호
• /
• pp.860-864
• /
• 1998

고상 반응법에 의해 제조된 $\textrm{Zn}_{1.98}\textrm{Mn}_{0.02}\textrm{SiO}_{4}$ 녹색 형광체에 Ga 원소를 치환시켜 소성온도 및 Ga의 첨가량에 따른 발광특성과 결정특성을 조사하였으나, $\textrm{Zn}_{1.98}\textrm{Mn}_{0.02}(\textrm{Si_{1-x}\textrm{Ga}_{x})\textrm{O}_{4}$ 형광체에 있어서 Ga을 첨가했을 경우가 첨가하지 않은 샘플에 비해 발광특성이 개선되었으며, 8mol%(x=0.08) Ga을 첨가했을 때 발광세기와 색순도에서 가장 우수한 특성을 보였다. $\textrm{Zn}_{1.98}\textrm{Mn}_{0.02}(\textrm{Si_{1-x}\textrm{Ga}_{x})\textrm{O}_{4}$ 형광체(x=0.08)에 대해서 소성온도를 $1100^{\circ}C$에서 $1400^{\circ}C$로 증가함에 따라 결정성이 개선되었으며 발광강도 역시 약 7배 이상 크게 증가하였다. 잔광시간은 Ga 첨가량에 관계없이 약 24 ms로 거의 변화가 없었다. 입도분석 결과 1-3$\mu\textrm{m}$의 작은 입자가 주로 관찰되었으며 10$\mu\textrm{m}$이상의 큰 응집입자도 소량 존재하였다.

• 한국방사선학회논문지
• /
• 제9권3호
• /
• pp.169-174
• /
• 2015

본 연구는 $LiGd_9(SiO_4)_6O_2:Ce^{3+}$ 형광체를 고상법으로 합성하여 X선 회절 실험으로 결정화 정도와 인회석 구조를 확인하였다. $LiGd_9(SiO_4)_6O_2:Ce^{3+}$ 형광체의 $Ce^{3+}$이온의 농도 변화에 따른 여기 및 방출 스펙트럼과 수명시간을 측정하였다. 여기 스펙트럼에서 $Ce^{3+}$ 이온의 농도 증가에 따라 276 nm ($Gd^{3+}$ $^8S_{7/2}{\rightarrow}^6I{_J}$ 전이) 형광 세기가 감소하는 에너지 전달을 확인하였다. 방출 스펙트럼에서 $Ce^{3+}$ 이온의 농도 증가에 따라 결정장의 변화에 의해 410 nm($Ce^{3+}$ $^2F_{5/2}$ and $^2F_{7/2}$) 방출 밴드의 파장이 장파장 쪽으로 이동하는 특성을 확인하였으며 314 nm에서 $Gd^{3+}$에서 $Ce^{3+}$로의 에너지 전달로 인해 $Gd^{3+}$ 형광 방출 세기가 감소하는 것을 확인하였다. $LiGd_9(SiO_4)_6O_2:Ce^{3+}$ 형광체의 $Ce^{3+}$의 수명시간은 약 20 ns로 짧은 특성을 나타내었고 $Ce^{3+}$의 농도가 증가하면 수명시간이 수 ns 감소하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.250-250
• /
• 2012

Recently, multiferroic materials have attracted much attention due to their fascinating fundamental physical properties and potential technological applications in magnetic/ferroelectric data storage systems, quantum electromagnets, spintronics, and sensor devices. Among single-phase multiferroic materials, $BiFeO_3$, in particular, has received considerable attention because of its very interesting magnetoelectric properties for application to spintronics. Enhanced ferromagnetism was found by Fe-site ion substitution with magnetic ions. In this study, $BiFe_{1-x}Ni_xO_3$ (x=0 and 0.05) bulk ceramic compounds were prepared by solid-state reaction and rapid sintering. High-purity $Bi_2O_3$, $Fe_3O_4$ and NiO powders were mixed with the stoichiometric proportions, and calcined at $450^{\circ}C$ for 24 h to produce $BiFe_{1-x}Ni_xO_3$. Then, the samples were directly put into the oven, which was heated up to $800^{\circ}C$ and sintered in air for 20 min. The crystalline structure of samples was investigated at room temperature by using a Rigaku Miniflex powder diffractometer. The Raman measurements were carried out with a Raman spectrometer with 514.5-nm-excitation Ar+-laser source under air ambient condition on a focused area of $1-{\mu}m$ diameter. The field-dependent magnetization and the temperature-dependent magnetization measurements were performed with a vibrating-sample magnetometer. The x-ray diffraction study demonstrates the compressive stress due to Ni substitution at the Fe site. $BiFe_{0.95}Ni_{0.05}O_3$ exhibits the rhombohedral perovskite structure R3c, similar to $BiFeO_3$. The lattice constant of $BiFe_{0.95}Ni_{0.05}O_3$ is smaller than of $BiFeO_3$ because of the smaller ionic radius of Ni3+ than that of Fe3+. The field-dependent magnetization of $BiFe_{0.95}Ni_{0.05}O_3$ exhibits a clear hysteresis loop at 300 K. The magnetic properties of $BiFe_{0.95}Ni_{0.05}O_3$ were improved at room temperature because of the existence of structurally compressive stress.

• 한국표면공학회지
• /
• 제50권4호
• /
• pp.282-288
• /
• 2017

$Eu^{3+}$- or $Sm^{3+}$-doped $La_2MoO_6$ phosphors were synthesized with different concentrations of activator ions via a solid-state reaction. The X-ray diffraction patterns exhibited that crystalline structures of all the phosphors were tetragonal systems with the dominant peak occurring at (103) plane, irrespective of the concentration and the type of activator ions. The crystallites showed the pebble-like crystalline shapes and the average crystallite size increased with a tendency to agglomerate as the concentration of $Eu^{3+}$ ions increased. The excitation spectra of $Eu^{3+}$-doped $La_2MoO_6$ phosphors contained an intense charge transfer band centered at 331 nm in the range of 250-370 nm and three weak peaks at 381, 394, and 415 nm, respectively, due to the $^7F_0{\rightarrow}^5L_7$, $^7F_0{\rightarrow}^5L_6$, and $^7F_0{\rightarrow}^5D_3$ transitions of $Eu^{3+}$ ions. The emission spectra under excitation at 331 nm exhibited a strong red band centered at 620 nm and two weak bands at 593 and 704 nm. As the concentration of $Eu^{3+}$ increased from 1 to 20 mol%, the intensities of all the emission bands gradually increased. For the $Sm^{3+}$-doped $La_2MoO_6$ phosphors, the emission spectra consisted of an intense emission band at 607 nm arising from the $^4G_{5/2}{\rightarrow}^6H_{7/2}$ transition and three relatively small bands at 565, 648, and 707 nm originating from the $^4G_{5/2}{\rightarrow}^6H_{5/2}$, $^4G_{5/2}{\rightarrow}^6H_{9/2}$, and $^4G_{5/2}{\rightarrow}^6H_{11/2}$ transitions of $Sm^{3+}$, respectively. The intensities of all the emission bands approached maxima when concentration of $Sm^{3+}$ ions was 5 mol%. These results indicate that the optimum concentrations for highly-luminescent red and orange emission are 20 mol% of $Eu^{3+}$ and 5 mol% of $Sm^{3+}$ ions, respectively.

• 한국세라믹학회지
• /
• 제45권11호
• /
• pp.701-706
• /
• 2008

High frequency dielectric ceramics have potential for applications in mobile and satellite communications systems at frequencies higher than 10GHz. The Ba$(Zn_{1/3}Ta_{2/3})O_3$ ceramics are known to have a high quality factor, a small temperature coefficient of the resonance frequency and a high dielectric constant. On the other hands, sintering at high temperature for extended time is required to obtain the ordered structure for high quality factor. In this study, the microwave dielectric properties of $ZrO_2$ and NiO-added Ba$(Zn_{1/3}Ta_{2/3})O_3$ ceramics prepared by solid-state reaction have been investigated. Adding $ZrO_2$ and NiO could effectively promote the densification even the case of decreasing the sintering time. At the surface of samples, secondary phase of Ba-Ta compounds was formed possibly due to the evaporation of ZnO, however, the interior of the samples remained as pure Ba$(Zn_{1/3}Ta_{2/3})O_3$. The samples sintered at $1600^{\circ}C$ for 2h exhibited 1:2 ordering of Zn and Ta cations. Excellent microwave dielectric properties of $Q{\cdot}f$(>96,000 GHz) and ${\varepsilon}_r$=30 has been obtained.

• Nuclear Engineering and Technology
• /
• 제5권1호
• /
• pp.44-54
• /
• 1973

방사성 $^{38}$ CL로 표지된 유기 하로겐 화합물의 제조방법을 가려내기 위하여서 Phenyl halides(7종), thloro nitrobenzene(6종), Chloro nitroanisole(2종), Chloro aniline (3종), Chloro anisidine(3종), Chloro toluene(3종), Benzyl chloride 유도체(4종) 및 기타 대조 화합물 3종 등을 원자로 내에서 조사하고 생성물을 알카리 수용액으로 주출하고 각각의 무기 $^{38}$ CL 수율을 조사시간 별로 검토하였다. 그 결과 화합물의 구조 보다도 표적물의 상태에 따라서 무기물 수율에 변화가 있고 고체상의 표적물의 경우에는 수율이 일반적으로 얕고 변화가 고르다는 것을 화인 하였다. 화학구조에 따르는 무기 $^{38}$ CL0의 생성수율의 감소는 현재까지의 결과로 보아서 Phenyl chlorides$^{38}$ CL 수율간에 Linear relationship가 있었으며 염소원자수가 많을수록 그 수율이 얕았다. 실험 결과를 논의하였으며 교지 반응에 대한 본 실험 결과의 응용성가능 여부를 고찰하였다.

• 한국결정학회지
• /
• 제13권3_4호
• /
• pp.165-171
• /
• 2002

고상반응법에 의해 합성된 분말을 $1100^{\circ}C$에서 소결함으로써 밀도가 $9.3g/cm^3$이고 평균입경이 $5.1{\pm}1.2{\mu}$인 $Pb(Fe_{1/2}Ta_{1/2})O_3$를 단일상으로 합성하였다. (공간군: Pm3m) $-150{\sim}50^{\circ}C$에서 측정된 비유전율은 인가전압의 주파수가 1kHz일 때 $-41^{\circ}C$에서 비유전율이 3100으로 최대값을 가지고 유전완화(dielectric relaxation)현상 및 완만한 상전이(diffuse phase transition, DPT)가 뚜렷하게 관찰되는 전형적인 완화형 강유전특성을 보였으며 소결후 $1000^{\circ}C$에서의 열처리 시간이 증가함 에 따라 상전이의 완만화도는 감소하여 정상 강유전체화 하였다. 한편, 소결직후 $Fe^{3+}$와 $Ta^{5+}$ 이온은 투과전자현미경으로도 검출할 수 없는 정도의 단거리 영역에서 화학양론적으로 1 : 1 질서 배열하고 있으며 이러한 B자리 양이온의 질서배열은 열처리 시간이 증가함에 따라 강화됨을 라만분광법으로 확인하였다. 소결직후 $Pb(Fe^{12}Ta_{1/2})O_3$센서의 완화형 강유전특성은 B자리 양이온의 화학양론적 1:1 단거리 질서배열구조와, 열처리한 $Pb(Fe_{1/2}TA_{1/2})O_3$에서의 완화형 강유전특성 감소는 열처리에 따라 강화된 화학양론적 1:1 단거리 질서배열구조와 연관지을 수 있었다.

• 한국재료학회지
• /
• 제5권5호
• /
• pp.583-597
• /
• 1995

We investigated the effect of the oxygne partial pressure on the phase stability of B $i_{2}$S $r_{2}$Ca C $u_{2}$ $O_{8+x}$ and B $i_{2}$S $r_{2}$C $a_{2}$C $u_{3}$ $O_{10+x}$ at 82$0^{\circ}C$. As the oxygen pressure decreased, B $i_{2}$Sr/sb 2/CaC $u_{2}$ $O_{8+x}$ melted at 2.2$\times$10$^{-3}$ atm $O_{2}$. In the case of the B $i_{1.7}$P $b_{0.4}$S $r_{2}$C $a_{2}$ $O_{10+x}$, it started to decompose into theree phases of B $i_{2}$S $r_{2}$Cu $O_{6+y}$, $Ca_{2}$Cu $O_{3}$ and C $u_{4}$ $O_{3}$ and C $u_{4}$ $O_{3}$ at 8.0$\times$10$^{-3}$ atm $O_{2}$ and was completely decomposed at 4.3$\times$10$^{-3}$ atm $O_{2}$ B $i_{2}$S $r_{2}$C $a_{2}$C $u_{3}$ $O_{10+x}$ phase was not formed by the solid state reaction from the mixutre of $i_{2}$S $r_{2}$CaCu.sub 2/ $O_{8+x}$, $Ca_{2}$Cu $O_{3}$ and CuO down to 2.2$\times$10.sub -3/ atm O.sub 2/ but formed by the solidifciation of the formed from the mixture of the intermediate compounds in the Bi-Sr-Ca-Cu-O system and the fromation temperature of Bi.sub 2/S $r_{2}$C $a_{2}$Cu.$_{3}$ $O_{10+x}$ can be lowered by reducing oxygen partial pressure.e.e.ure.e.e.

• Bulletin of the Korean Chemical Society
• /
• 제30권8호
• /
• pp.1719-1723
• /
• 2009

The LiFeP$O_4$ powder was synthesized by using the solid state reaction method with Fe($C_2O_4){\cdot}2H_2O,\;(NH_4)_2HPO_4,\;Li_2CO_3$, and chitosan as a carbon precursor material for a cathode of a lithium-ion battery. The chitosan added LiFePO4 powder was calcined at 350 ${^{\circ}C}$ for 5 hours and then 800 ${^{\circ}C}$ for 12 hours for the calcination. Then we calcined again at 800 ${^{\circ}C}$ for 12 hours. We characterized the synthesized compounds via the crystallinity, the valence states of iron ions, and their shapes using TGA, XRD, SEM, TEM, and XPS. We found that the synthesized powders were carbon-coated using TEM images and the iron ion is substituted from 3+ to 2+ through XPS measurements. We observed voltage characteristics and initial charge-discharge characteristics according to the C rate in LiFeP$O_4$ batteries. The obtained initial specific capacity of the chitosan added LiFeP$O_4$ powder is 110 mAh/g, which is much larger than that of LiFeP$O_4$ only powder.